MODEL G0813/G0814 6" JOINTER OWNER'S MANUAL (For models manufactured since 03/16) COPYRIGHT © MARCH, 2016 BY GRIZZLY INDUSTRIAL, INC. REVISED SEPTEMBER, 2016 (BL) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL18046 PRINTED IN TAIWAN V1.09.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Contact Info.................................................... 2 Machine Differences....................................... 2 Manual Accuracy............................................ 2 Identification.................................................... 3 Controls & Components.................................. 4 G0813 Machine Data Sheet........................... 6 G0814 Machine Data Sheet...........................
INTRODUCTION Contact Info Manual Accuracy We stand behind our machines! If you have questions or need help, contact us with the information below. Before contacting, make sure you get the serial number and manufacture date from the machine ID label. This will help us help you faster. We are proud to provide a high-quality owner’s manual with your new machine! Grizzly Technical Support 1815 W. Battlefield Springfield, MO 65807 Phone: (570) 546-9663 Email: techsupport@grizzly.
Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. A B C D E F O H N I M J G K L A. B. C. D. E. F. G. H. Outfeed Table Fence Cutterhead Guard Fence Lock Fence Tilt Handle Infeed Table Infeed Table Lever Fence Tilt Lock I. J. K. L. M. N. O.
Controls & Components To reduce your risk of serious injury, read this entire manual BEFORE using machine. C B D G J Refer to Figures 1–4 and the following descriptions to become familiar with the basic controls and components of this machine. Understanding these items and how they work will help you understand the rest of the manual and stay safe when operating this machine. E Figure 2. Main table controls, fence, and foot pedal caster. B.
H N O M L I F K P Figure 3. Cutterhead guard and depth-of-cut scale. H. Cutterhead Guard: Covers cutterhead until pushed out of the way by workpiece during operation. When workpiece leaves cutterhead, guard springs back to its starting position. I. F. Depth-of-Cut Scale: Indicates cutting depth of a single pass. Outfeed Table Handwheel: Adjusts position of outfeed table. Typically only used when setting outfeed table even with cutterhead knives or when servicing the cutterhead. Figure 4.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0813 6" JOINTER WITH KNOCK‐DOWN STAND Product Dimensions: Weight.............................................................................................................................................................. 247 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Main Specifications: Main Specifications Jointer Size.................................................................................................................................................. 6 in. Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R Maximum Width of Cut................................................................................................................................
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0814 6" JOINTER WITH CABINET STAND Product Dimensions: Weight.............................................................................................................................................................. 245 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.
Main Specifications: Main Specifications Jointer Size.................................................................................................................................................. 6 in. Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R Maximum Width of Cut................................................................................................................................
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts. HAZARDOUS DUST. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material.
Additional Safety for Jointers Serious cuts, amputation, entanglement, or death can occur from contact with rotating cutterhead or other moving components! Flying chips can cause blindness or eye injuries. Workpieces or inserts/knives thrown by cutterhead can strike nearby operator or bystanders with deadly force. To reduce the risk of these hazards, operator and bystanders MUST completely heed the hazards and warnings below. KICKBACK. Occurs when workpiece is ejected from machine at a high rate of speed.
SECTION 2: POWER SUPPLY Availability Circuit Information Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.
Grounding Requirements This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. For 110V operation: This machine is equipped with a power cord that has an equipment-grounding wire and a grounding plug (see following figure).
Voltage Conversion to 220V The voltage conversion MUST be performed by an electrician or qualified service personnel. The voltage conversion procedure consists of rewiring the motor and installing the correct plug. A wiring diagram is provided on Page 56 for your reference. 4. Use wire nuts to connect wires as indicated in Figure 8. Twist wire nuts onto their respective wires and wrap them with electrical tape so they will not come loose.
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! HEAVY LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.
Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Cap Screw 5mm 5mm Model G0813/G0814 (Mfd.
G0813 Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. NOTICE If you cannot find an item on this list, carefully check around/inside the machine and packaging materials.
G0814 Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. NOTICE If you cannot find an item on this list, carefully check around/inside the machine and packaging materials.
Cleanup The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.
Assembly 2. The machine must be fully assembled before it can be operated. Before beginning the assembly process, refer to Needed for Setup and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if applicable). The Model G0813 jointer stand must be assembled. The Model G0814 stand requires no assembly. Therefore, if assembling the Model G0813, start at Step 1.
4. Attach each of the four corner supports to top plate with (4) #10-24 x 3⁄8" flange screws, as shown in Figure 18. Ensure flange of each support is installed inside top plate. 6. Corner Support Attach motor cord and power cord wires to ON/OFF switch terminals (see Figure 20). Ensure motor cord wires attach to horizontal terminals and power cord wires attach to vertical terminals. Horizontal Terminal Motor Cord GND GND x4 Power Cord Figure 18. Corner supports attached to top plate. 5.
8. Remove motor junction box cover, loosen strain relief, then insert motor cord into junction box, as shown in Figure 22. 9. Attach ground wire with pre-installed ground wire screw (see Figure 22). Strain Relief Right Panel Ground Wire Screw Figure 22. Inserting wires into junction box. 10. Remove wire nuts (see Figure 22) and disconnect wires, then use wire nuts to reconnect wires, as indicated in Figure 23.
17. Tighten all fasteners on stand. 18. G0814 Only: Turn stand upside down and place top on flat surface. 19. Attach foot pedal caster assembly to side of mobile base chassis with leveling feet, using (2) 3⁄8"-16 x 21⁄2" hex bolts, (4) 3⁄8" flat washers, (2) 3⁄8"-16 hex nuts, and (1) 5⁄16"-18 x 2" hex bolt and (1) 5⁄16" flat washer, as shown in Figure 27. 22. With help of another person, place jointer assembly onto stand.
24. Loosen set screws on cutterhead or motor pulley as needed to align pulleys, then tighten set screws (see Figure 31). x2 27. Adjust belt tension by applying downward pressure on motor until there is approximately 1⁄4" deflection when belt is pushed with moderate force, as shown in Figure 34. Note: After the first 16 hours of operation, check and re-tension the belt, as it may stretch and seat during this time, which will cause it to lose the initial tension you set.
30. Install fence tilt lever (see Figure 36). When outfeed table height is correctly set, knife (at top dead center) will barely touch straightedge, as illustrated in Figure 37. — If knife lifts straightedge off table or is below straightedge, then outfeed table height must be reset (refer to Setting Outfeed Table Height, Steps 5-8, on Page 48 for detailed instructions). Tilt Lever Figure 36. Fence tilt lever installed.
36. Assemble knife-setting gauge, as shown in Figure 40. Cutterhead guard must always return to closed position whenever it is moved. If it does not do this, it must be re-adjusted or re-installed. 34. Test operation of guard by pulling it back. Guard should spring back over cutterhead and stop against fence. — If guard does not snap back, or snaps back slowly, remove guard and repeat Steps 32–34. 35. Install belt guard with (1) 5⁄16"-18 x 21⁄2" hex bolt and (1) 5⁄16" flat washer (see Figure 39).
Dust Collection This machine creates a lot of wood chips/ dust during operation. Breathing airborne dust on a regular basis can result in permanent respiratory illness. Reduce your risk by wearing a respirator and capturing the dust with a dust collection system. Recommended CFM at Dust Port: 400 CFM Do not confuse this CFM recommendation with the rating of the dust collector.
4. Recommended Adjustments Remove switch disabling key, as shown in Figure 43. For your convenience, the adjustments listed below have been performed at the factory and no further setup is required to operate your machine. However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine. Figure 43. Removing switch key from paddle switch. 5. Try to start machine with paddle switch.
This overview covers the basic process that happens during a typical operation with this machine. Familiarize yourself with this process to better understand the controls and procedures explained throughout the Operations section. SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand.
Stock Inspection & Requirements Follow these rules when choosing and jointing stock: • DO NOT joint or surface plane stock that contains large or loose knots. Injury to the operator or damage to the workpiece can occur if a knot becomes dislodged during the cutting operation. • DO NOT joint or surface plane against the grain direction. Cutting against the grain increases the likelihood of kickback, as well as tear-out on the workpiece.
Setting Depth of Cut The depth of cut on a jointer is the amount of material removed from the bottom of the workpiece as it passes over the cutterhead. The depth of cut is set by adjusting the height of the infeed table relative to the cutterhead knives at TDC (top dead center). Depth-of-Cut Scale The depth of cut can be referenced directly from the depth scale located on the front of the jointer (see Figures 47–48). Note: The depth scale can be calibrated or "zeroed" if it is not correct.
Squaring Stock 3. Edge Joint on Jointer—Concave edge of workpiece is jointed flat with jointer. 4. Rip Cut on a Table Saw—Jointed edge of workpiece is placed against a table saw fence and opposite edge cut off. Squaring stock involves four steps performed in the order below: 1. 2. Surface Plane on Jointer—Concave face of workpiece is surface planed flat with jointer. Surface Plane on a Thickness Planer— Opposite face of workpiece is surface planed flat with a thickness planer.
Surface Planing The purpose of surface planing (see Figures below) on the jointer is to make one flat face on a piece of stock to prepare it for thickness planing on a planer. NOTICE If you are not experienced with a jointer, set depth of cut to 0", and practice feeding workpiece across tables as described. This will help you prepare for actual operations.
Edge Jointing Edge jointing (see Figures below) produces a flat and true surface along the side of a workpiece by removing uneven areas. It is an essential step for squaring up warped or rough stock and when preparing a workpiece for joinery or finishing. NOTICE If you are not experienced with a jointer, set depth of cut to 0", and practice feeding workpiece across tables as described. This will help you prepare for actual operations. To edge joint on jointer: 1.
Bevel Cutting Bevel cuts (see Figures below) can be made by setting the fence at the desired angle and feeding the workpiece firmly along the fence face, with the bottom inside corner firmly against the table. The cutting process typically requires multiple passes or cuts to bevel the entire edge of a workpiece. NOTICE If you are not experienced with a jointer, set depth of cut to 0", and practice feeding workpiece across tables as described. This will help you prepare for actual operations.
Rabbet Cutting The purpose of rabbet cutting is to remove a section of the workpiece edge (see Figures below). When combined with another rabbet cut edge, the rabbet joints create a simple, yet strong method of joining stock. When cutterhead guard is removed, attempting any other cut besides a rabbet directly exposes operator to moving cutterhead.
ACCESSORIES SECTION 5: ACCESSORIES Basic Eye Protection Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to our website or latest catalog for additional recommended accessories.
H7653—6" Spiral Cutterhead This cutterhead replaces the standard straight knife cutterheads on our Grizzly jointers . Has four spirals with indexable, four-sided carbide inserts, so each insert can be rotated for a new factory sharp edge. Cutterhead includes cast iron pulleys, bearing blocks, mounting studs, 5 extra inserts, T-handle wrench, Torx bits and spare insert screws. Has an incredible finish, and is comparable to Byrd cutterheads in quality of cut as well as the quality of the cutterhead itself.
SECTION 6: MAINTENANCE To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Cleaning & Protecting Schedule The cleaning process for this machine is simple. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Treat all unpainted cast iron and steel with a non-staining lubricant after cleaning.
Lubrication Since all bearings are sealed and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them. It is essential to clean components before lubricating them because dust and chips build up on lubricated components and make them hard to move. Simply adding more grease to them will not yield smooth moving components. Table Ways Oil Type..... Grizzly T23962 or ISO 68 Equivalent Oil Amount............................................
SECTION 7: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Machine does not start or a breaker trips immediately after startup. 1. Switch disabling key removed. 2.
Machine Operation Symptom Possible Cause Possible Solution Table(s) difficult to adjust. 1. Table lock(s) engaged/partially engaged. 2. Infeed table stop blocking upward movement. 1. Completely loosen table lock(s) (Page 4). 2. Loosen/reset infeed table stop bolt (Page 33). 1. Outfeed table set too low, or knives set too Excessive snipe (gouge in end of high. board that is uneven with rest of cut). 2. Operator pushing down on trailing end of workpiece as it leaves cutterhead. 1.
Inspecting Knives The height of the knives can be inspected with a straightedge to ensure that they are set even with the outfeed table at their highest point in the cutterhead rotation, or top dead center (TDC). To inspect knives: 1. DISCONNECT MACHINE FROM POWER! 2. Remove cutterhead guard or block it open. 3. Using a straightedge on outfeed table, check height of each knife at positions as shown.
Tools Needed Qty Knife-Setting Jig................................................. 1 Hex the Wrench 3mm............................................... 1 Use knife-setting jig to verify that all knives are Open-End Wrenchin8mm.................................... 1 positioned evenly the cutterhead. To inspect positioning of knives in cutterhead: Figure 68. Example of using Jointer Pal®.
6. To set or replace knives: 1. DISCONNECT MACHINE FROM POWER! 2. Remove cutterhead guard from table and lower infeed and outfeed tables as far as they go. This will provide unrestricted access to cutterhead. 3. Remove cabinet rear access panel to expose cutterhead pulley. 4. Rotate cutterhead pulley to provide good access to cutterhead knives, and put on leather gloves. 5.
Setting Outfeed Table Height When correctly set, the knife will barely touch straightedge, as shown in Figure 75. — If your outfeed table is correctly set, no adjustments are necessary. The outfeed table height must be even with the top of the cutterhead knives when they are positioned at top dead center. If the outfeed table is set too low, there will be snipe. If the outfeed table is set too high, the workpiece will hit the edge of the outfeed table during operation, increasing the chance of kickback.
Calibrating Depth Scale 6. Adjusting Gibs The depth scale can be calibrated or "zeroed" to make sure the cutting depth shown on the scale matches the actual cutting depth (per pass). Before beginning, set outfeed To calibrate the depth scale: table height as described in Setting Outfeed Table Height. 1. Set the outfeed table height as described in Tools Needed Qty Setting Outfeed Table Height. Straightedge....................................................... 1 Phillips Screwdriver #2...................
Setting Fence Stops The fence stops simplify the task of adjusting the fence to 90˚ and 135˚ (45˚ outward). Setting 135° Fence Stop 1. Disengage swing stop (see Figure 81). 2. Use a sliding bevel adjusted to 135˚ to adjust fence to 135˚ (45˚ outward) position, as shown in Figure 82. Tools Needed Qty 45° Square......................................................... 1 90° Square......................................................... 1 Sliding Bevel.....................................................
Replacing/ Tensioning Belt — If there is more than 1⁄4" deflection when you check belt tension, repeat the tensioning procedure until it is correct. Cutterhead Pulley To ensure optimum power transmission from the motor to the cutterhead, the belt must be in good condition (free from cracks, fraying and wear) and properly tensioned. After the first 16 hours of belt life, re-tension the belt, as it will stretch and seat during this time. Tool Needed Qty Wrench or Socket 12mm................................
Aligning Pulleys Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplaner) for optimum performance. Straightedge The pulleys can be adjusted by loosening the pulley set screws, aligning the pulleys, and retightening the set screws. Tool Needed Qty Hex Wrench 3mm............................................... 2 Straightedge.......................................................
Checking/Adjusting Table Parallelism 5. —If there are no gaps, and the straightedge makes full contact with both tables at front and rear, the tables are parallel with each other and no adjustments are necessary. The infeed and outfeed tables must be parallel with each other in order to produce a straight, jointed edge. When the tables are not parallel with each other, the jointer will produce workpieces that are cupped (concave) or bowed (convex) along their length.
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
110V Wiring Diagram Neutral Hot 110 VAC 5-15 Plug Ground ON/OFF Switch (Viewed from Behind) KEDU HY-18 20/12A 125/250V GND GND Figure 92. ON/OFF switch wiring (viewed from behind). Ground MOTOR Motor Junction Box Start Capacitor Figure 91. Motor junction box. Model G0813/G0814 (Mfd.
220V Wiring Diagram Hot Hot G 220VAC 6-15 Plug Ground ON/OFF Switch (Viewed from Behind) KEDU HY-18 20/12A 125/250V GND GND Indicates wiring changes for 220V conversion Ground MOTOR Figure 93. ON/OFF switch wiring (viewed from behind). -56- Motor Junction Box Start Capacitor 300MFD 125VAC Model G0813/G0814 (Mfd.
SECTION 9: PARTS Table 33 32 We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/ parts to check for availability. 29 30 3 30 34 42 8 58 9 40 11 18 36 10 41 31 14 25 16 12 43 43 6 15 19 51 49 52 27 7 2 1 5 60 60 35 28 26 60 59 53 39 21 54 23 22 24 4 57 Model G0813/G0814 (Mfd.
Table Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 TABLE BASE INFEED TABLE OUTFEED TABLE GIB TABLE LOCK HANDLE M8-1.25 X 30 SET SCREW M8-1.25 X 25 HEX NUT M8-1.
Fence 129 130 128 125 123 123 122 117 101 103 126 104 121 118 133 113 119 112 102 114 115 116 124 120 111 102 110 132 108 105 109 126 127 106 131 REF PART # DESCRIPTION REF PART # DESCRIPTION 101 102 103 104 105 106 108 109 110 111 112 113 114 115 116 117 FENCE PIVOT STUD 1/2-20 X 5/8 FENCE HINGE SET SCREW 3/8-16 X 1-1/2 CONE-PT HEX NUT 3/8-16 TILT LEVER 3/8-16 X 1/2 FLAT HD CAP SCR 5/16-18 X 1-3/4 FENCE BRACKET FENCE STOP BRACKET SHOULDER BOLT 5/16-18 X 112, 3/8 X 3/4 HEX N
Cutterhead 215 213 202 212 205 211 214 218 219 208 204 217 207 210 209 201 206 218 217 220 219 208 218A 207 206 REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 204 205 206 207 208 209 210 211 CUTTERHEAD 6" 3-KNIFE KNIFE 6" X 1" X 1/8" (3-PC) SET KNIFE GIB GIB BOLT 1/4-20 X 1/4 W/8MM HEAD HEX NUT 3/8-24 LOCK WASHER 3/8 STUD-SE 3/18-16 X 3-1/2, 3/4" BEARING BLOCK (LEFT) BALL BEARING 6202-2RS KEY 5 X 5 X 30 212 213 214 215 217 218A 218 219 220 BALL BEARING 6203-2RS BEARING BLOCK
G0813 Stand 304 334 301 330 391 326 330 316 311 315 305 389 314 303 335 316 313 330 308 313 330 322 310 321 317 306 327 307 328 329 326 318 312 335 316 320 311 310 319 302 338 339 385 379 385 341 384 366 365 325 316 393 375 340 367 387 330 350 375 386 390 382 381 380 374 361 366 368 377 367 320-2 320-3 320-4 362 369 376 363 377 364 371 370 371 377 378 320-1 376 372 373 379 350 375 Model G0813/G0814 (Mfd.
G0813 Stand Parts List REF PART # 301 P0813301 302 P0813302 303 P0813303 304 P0813304 305 P0813305 306 P0813306 307 P0813307 308 P0813308 310 P0813310 311 P0813311 312 P0813312 313 P0813313 314 P0813314 315 P0813315 316 P0813316 317 P0813317 318 P0813318 319 P0813319 320 P0813320 320-1 P0813320-1 320-2 P0813320-2 320-3 P0813320-3 320-4 P0813320-4 320-5 P0813320-5 320-6 P0813320-6 320-7 P0813320-7 320-8 P0813320-8 320-9 P0813320-9 320-10 P0813320-10 321 P0813321 322 P0813322 325 P0813325 326 P0813326 327 P
G0814 Stand 331 333 333 332 334 328 326 327 308 316 329 322 315 393 326 325 375 390 350 375 385 385 384 374 382 381 380 386 379 312 313 306 321 339 338 340 319 341 317 314 320 318 367 366 365 361 366 368 377 367 369 376 362 376 363 377 364 371 370 371 377 378 320-1 372 373 379 350 360A 375 Model G0813/G0814 (Mfd.
G0814 Stand Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 306 308 312 313 314 315 316 317 318 319 320 320-1 320-2 320-3 320-4 320-5 320-6 320-7 320-8 320-9 320-10 321 322 325 326 327 328 329 331 332 333 334 338 339 P0814306 P0814308 P0814312 P0814313 P0814314 P0814315 P0814316 P0814317 P0814318 P0814319 P0814320 P0814320-1 P0814320-2 P0814320-3 P0814320-4 P0814320-5 P0814320-6 P0814320-7 P0814320-8 P0814320-9 P0814320-10 P0814321 P0814322 P0814325 P0814326 P0814327 P0814328 P0814329 P081433
G0813 Labels & Cosmetics 401 402 409 408 403 407 404 406 405 403 REF PART # DESCRIPTION REF PART # DESCRIPTION 401 402 403 404 405 CUTTERHEAD EXPOSURE WARNING LABEL CUTTERHEAD WARNING LABEL ELECTRICITY LABEL MACHINE ID LABEL GRIZZLY.
G0814 Labels & Cosmetics 401 402 412 403 411 404 405 410 406 409 408 404 407 REF PART # DESCRIPTION REF PART # DESCRIPTION 401 402 403 404 405 406 CUTTERHEAD EXPOSURE WARNING LABEL CUTTERHEAD WARNING LABEL EYE/EAR/LUNG WARNING LABEL ELECTRICITY LABEL MODEL NUMBER LABEL GRIZZLY NAMEPLATE-SMALL 407 408 409 410 411 412 GRIZZLY.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
