MODEL G0855/G0856 8" DOVETAIL JOINTER w/MOBILE BASE OWNER'S MANUAL (For models manufactured since 02/19) 175370 COPYRIGHT © OCTOBER, 2018 BY GRIZZLY INDUSTRIAL, INC. REVISED JANUARY, 2019 (ES) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #ES19680 PRINTED IN TAIWAN V2.01.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Contact Info.................................................... 2 Machine Differences....................................... 2 Manual Accuracy............................................ 2 Identification.................................................... 3 Controls & Components.................................. 4 Machine Data Sheet (G0855)......................... 6 Machine Data Sheet (G0856).........................
INTRODUCTION Contact Info Manual Accuracy We stand behind our machines! If you have questions or need help, contact us with the information below. Before contacting, make sure you get the serial number and manufacture date from the machine ID label. This will help us help you faster. We are proud to provide a high-quality owner’s manual with your new machine! Grizzly Technical Support 1815 W. Battlefield Springfield, MO 65807 Phone: (570) 546-9663 Email: techsupport@grizzly.
Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual.
Controls & Components C H To reduce your risk of serious injury, read this entire manual BEFORE using machine. Refer to Figures 1–5 and the following descriptions to become familiar with the basic controls and components of this machine. Understanding these items and how they work will help you understand the rest of the manual and stay safe when operating this machine. D E F G Figure 2. Table controls and components. mobile base lock knobs C.
I J K L O P Q S R T U Figure 3. Table locks, cutterhead guard, and depth-of-cut scale. I. Outfeed Table Lock: Tighten to secure outfeed table position; loosen for table adjustment. J. Cutterhead Guard: Covers cutterhead until workpiece pushes guard out of the way during operation. When workpiece leaves cutterhead, guard springs back to its starting position. K. Infeed Table Lock: Tighten to secure infeed table position; loosen for table adjustment. L.
Machine Data Sheet (G0855) MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0855 8" X 72" DOVETAIL JOINTER WITH BUILT‐IN MOBILE BASE Product Dimensions: Weight.............................................................................................................................................................. 335 lbs. Width (side-to-side) x Depth (front-to-back) x Height..............................................................
Main Specifications: Main Specifications Jointer Size.................................................................................................................................................. 8 in. Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R Maximum Width of Cut................................................................................................................................
Machine Data Sheet (G0856) MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0856 8" DOVETAIL JOINTER WITH SPIRAL CUTTERHEAD & MOBILE BASE Product Dimensions: Weight.............................................................................................................................................................. 335 lbs. Width (side-to-side) x Depth (front-to-back) x Height.........................................................
Main Specifications: Main Specifications Jointer Size.................................................................................................................................................. 8 in. Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R Maximum Width of Cut................................................................................................................................
Safety SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts. HAZARDOUS DUST. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material.
Additional Safety for Jointers Serious cuts, amputation, entanglement, or death can occur from contact with rotating cutterhead or other moving components! Flying chips from cutting operations can cause eye injuries or blindness. Workpieces or inserts/knives thrown by cutterhead (kickback) can strike nearby operator or bystanders with deadly force. To reduce the risk of serious personal injury from these hazards, operator and bystanders MUST completely heed the hazards and warnings below. KICKBACK.
SECTION 2: POWER SUPPLY Power Supply Availability Circuit Information Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.
Grounding Requirements This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. This machine is equipped with a power cord that has an equipment-grounding wire and a grounding plug. Only insert plug into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! HEAVY LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.
Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. NOTICE If you cannot find an item on this list, carefully check around/inside the machine and packaging materials.
Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Cap Screw 5mm 5mm Model G0855/G0856 (Mfd.
Cleanup The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.
Assembly 3. Remove top and sides of wood shipping crate, then place small items aside in safe location. The machine must be fully assembled before it can be operated. Before beginning the assembly process, refer to Needed for Setup and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if applicable). 4.
7. Adjust position of table assembly so cutterhead and motor pulleys are aligned, and then secure table assembly to stand with (3) M10-1.5 x 40 standoff hex bolts and (3) 10mm lock washers (see Figure 13). 9. Loosen motor mount fasteners shown in Figure 15. DO NOT completely remove fasteners. 10. Slide motor upward, place V-belt around cutterhead pulley and motor pulley, then slide motor down to rest on belt (see Figure 15). V-Belt Motor Pulley Figure 13. Table assembly secured to stand. 8.
11. Look down length of belt and pulley faces to check pulley alignment (see Figures 16–17). If available use a narrow straightedge against pulley faces to check alignment. Cutterhead Pulley Belt 14. Adjust belt tension by applying downward pressure on motor until there is approximately 1⁄4" deflection when belt is pushed with moderate force, as shown in Figure 18.
17. Attach switch pedestal to stand with (2) M8-1.25 x 20 cap screws and (2) 8mm lock washers (see Figure 19). 18. Connect switch cord to motor cord (see Figure 19). Note: The switch cord and motor cord have matching plugs for easy connection. 20. Slide handwheels onto leadscrews, and secure with pre-installed 5/16"-18 x 1/2" Phillips head screws and 5/16" fender washers (see Figure 21). Handwheel (1 of 2) Leadscrew (1 of 2) Switch Pedestal x2 Figure 21. Handwheel secured to leadscrew (1 of 2).
22. Insert cutterhead guard shaft into mounting hole on table, then tighten set screw to secure (see Figure 22). Knife-Setting Jig (G0855) Assemble the knife-setting jig (see Figure 23) using the knife-setting jig rod, feet, and external retaining rings. Figure 22. Cutterhead guard installed. The cutterhead guard is a critical safety feature of this jointer.
Dust Collection This machine creates a lot of wood chips/ dust during operation. Breathing airborne dust on a regular basis can result in permanent respiratory illness. Reduce your risk by wearing a respirator and capturing the dust with a dust-collection system. Recommended CFM at Dust Port: 400 CFM Do not confuse this CFM recommendation with the rating of the dust collector.
Tightening Belt The final step in the setup process must be done after approximately 16 hours of operation. During this first 16 hours, the belt will stretch and seat into the pulley groove. After this time, you must re-tension the belt to avoid slippage and burn out. Refer to Page 52 when you are ready to perform this important adjustment. Note: Pulleys and belt can get hot. This is a normal condition. Allow them to cool before making adjustments.
SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand. Due to the generic nature of this overview, it is not intended to be an instructional guide.
Stock Inspection & Requirements Stock Inspection Requirements Follow these rules when choosing and jointing stock: • DO NOT joint or surface plane stock that contains large or loose knots. Injury to the operator or damage to the workpiece can occur if a knot becomes dislodged during the cutting operation. • DO NOT joint or surface plane against the grain direction. Cutting against the grain increases the likelihood of kickback, as well as tear-out on the workpiece.
Squaring Stock 2. Surface Plane on a Thickness Planer— Opposite face of workpiece is surface planed flat with a thickness planer. Squaring stock means making it flat and parallel along both length and width, and making the length and width perpendicular to one another. The purpose of squaring stock is to prepare it for accurate cuts and construction later on.
Surface Planing The purpose of surface planing (see example Figures below) on the jointer is to make one flat face on a piece of stock to prepare it for thickness planing on a planer. Failure to use push blocks when surface planing could result in your hands contacting rotating cutterhead, which will cause serious personal injury. ALWAYS use push blocks when surface planing on jointer! To surface plane on jointer: 1.
Edge Jointing Edge jointing (see example Figures below) produces a flat and true surface along the side of a workpiece by removing uneven areas. It is an essential step for squaring up warped or rough stock and when preparing a workpiece for joinery or finishing. To edge joint on jointer: 1. Inspect stock to ensure it is safe and suitable for the operation (see Stock Inspection & Requirements section). 2. Set infeed table height to desired cutting depth for each pass.
Bevel Cutting Bevel cuts (see example Figures below) can be made by setting the fence at the desired angle and feeding the workpiece firmly along the fence face, with the bottom inside corner firmly against the table. The cutting process typically requires multiple passes or cuts to bevel the entire edge of a workpiece. To bevel cut on jointer: 1. Inspect stock to ensure it is safe and suitable for the operation (see Stock Inspection & Requirements section). 2.
Rabbet Cutting A rabbet cut removes a portion of a workpiece edge, so it fits together with an opposing, equally sized rabbet cut on another workpiece (see example Figure below). This is a classic method of joining two workpieces that is simple, yet strong. To rabbet cut on jointer: 1. Inspect stock to ensure it is safe and suitable for the operation (see Stock Inspection & Requirements section). 2. Set infeed table height to desired cutting depth for each pass.
4. Set fence to 90° and near front of jointer, so amount of exposed cutterhead in front of fence matches size of desired rabbet. Setting Depth of Cut Setting Depth of Cut 5. Start jointer. 6. Place workpiece firmly against fence and infeed table. 7. The depth of cut on a jointer affects the amount of material removed from the bottom of the workpiece as it passes over the cutterhead. CAUTION: To ensure workpiece remains stable during cut, concave sides of workpiece must face toward table and fence.
To lower the infeed table below the 1⁄ 8" depth stop, pull the release knob (see Figure 33), adjust the table height, and then tighten the lock to secure the setting. ⁄ 8" Depth Stop Release Knob 1 Upper Stop Screw Upper Jam Nut ⁄ 8" Depth Stop Release Knob 1 Lower Stop Screw Table Pin Lower Jam Nut Figure 35. Positive-stop components for infeed table. Figure 33. Infeed table height controls.
Accessories SECTION 5: ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. NOTICE H7654—8" Indexable Spiral Cutterhead These cutterheads replace the standard straightknife cutterheads on our Grizzly jointers and planers.
H4982—HSS Jointer Knives, 4 Pk. 8" x 3 ⁄4" x 1⁄ 8" replacement HSS jointer knives. H2499—Small Half-Mask Respirator H3631—Medium Half-Mask Respirator H3632—Large Half-Mask Respirator H3635—Cartridge Filter Pair P100 If you work around dust everyday, a half-mask respirator can be a lifesaver. Also compatible with safety glasses! H3631 H3635 Figure 39. H4982 Jointer Knives for Model G0855.
SECTION 6: MAINTENANCE To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Schedule For optimum performance from this machine, this maintenance schedule must be strictly followed. Ongoing To maintain a low risk of injury and proper machine operation, if you ever observe any of the items below, shut down the machine immediately and fix the problem before continuing operations: Loose mounting bolts.
Lubrication Lubrication Since all bearings are sealed and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them. It is essential to clean components before lubricating them because dust and chips build up on lubricated components and make them hard to move. Simply adding more grease to them will not yield smooth moving components. Leadscrews Oil Type..... Grizzly T27914 or ISO 68 Equivalent Oil Amount............................................
SECTION 7: SERVICE Review the troubleshooting procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Machine does not start or a breaker trips immediately after startup. 1. Incorrect power supply voltage/circuit size. 2.
Machine Operation Symptom Possible Cause Possible Solution Table is hard to adjust. 1. Table lock engaged/partially engaged. 2. Table stop blocking movement. 3. Table gibs out of adjustment. 1. Completely loosen table lock (Page 5). 2. Loosen/reset table stop (Page 35). 3. Adjust table gibs (Page 46). 1. Outfeed table set too low. Excessive snipe (gouge in end of board that is uneven 2. Knives set too high (G0855). with rest of cut). 3.
Setting/Replacing Knives (G0855) Setting the knives correctly is crucial to the proper operation of the jointer and it plays an important role in keeping the knives sharp. If one knife is higher than the others, it will do the majority of the work, and thus, become dull much faster. Inspecting Knives jig included with the jointer designed The knife cutterhead on this jointer comesis with both to all theand knives evenly and atknife the correct for setting height.
Knife-Setting Jig Method 5. The infeed table is lowered to fit the jig on the cutterhead, as shown, and the knife heights are set to just touch the middle pad of the jig. The knife-setting jig included with the jointer is designed to set all the knives evenly and at the correct height in the cutterhead. Closely examine how jig touches cutterhead and knife.
5. Loosen cutterhead gib bolts, starting in the middle, and alternating back and forth until all gib bolts are loose, but not falling out. The first time you set or replace a knife, remove the gib and knife from cutterhead. Clean gib and clean inside cutterhead slot to remove all pitch or sawdust. Coat knife and gib with a metal protectant. 6. Position knife jig over knife. Loosen gib bolts until knife is completely loose. 7.
Rotating/Replacing Spiral Cutterhead Inserts (G0856) Rotating Replacing Cutterhead Inserts The spiral cutterhead is equipped with 4-sided indexable carbide inserts. Each insert can be removed, rotated, and re-installed to use any one of its four cutting edges. Therefore, if one cutting edge becomes dull or damaged, simply rotate it 90˚ (as shown below) to use a sharp cutting edge. The inserts have a reference dot on one corner.
7. Adjusting Gibs Remove Torx screw and insert, then carefully clean away all dust and debris from insert and insert pocket in cutterhead. Adjusting Gibs IMPORTANT: This step is critical for achieving a smooth finish with cutting operations. Dirt or dust trapped under insert during installation will slightly raise insert in cutterhead, which will leave marks on workpiece after jointing. Tip: Use low-pressure compressed air or a vacuum nozzle to clean cutterhead pocket. 8.
Checking/Adjusting Table Parallelism 5. Checking Adjusting Table Parallelism — If there are no gaps, and the straightedge makes full contact with both tables at front and rear, the tables are parallel with each other and no adjustments are necessary. The infeed and outfeed tables must be parallel with each other in order to produce a straight, jointed edge.
Setting Outfeed Table Height Setting Outfeed Table Height 6. Use motor pulley to rotate cutterhead until one knife or insert is at TDC (its highest point during rotation), as shown in Figures 64–65. 7. Use outfeed table handwheel to set outfeed table so knife or insert barely touches straightedge, as shown in Figure 65. To help ensure safe operation and best cutting results, set the outfeed table height level with the knives/inserts when they are at top-deadcenter (TDC).
Setting Fence Stops 4. Setting Fence Stops The fence stops simplify the task of adjusting the fence to 45° inward, 90°, and 45° outward (135°). Item(s) Needed: Qty Open-End Wrench 14mm................................... 1 Sliding Bevel....................................................... 1 Setting 90° Stop 1. DISCONNECT MACHINE FROM POWER! 2. Loosen fence tilt lock, rotate stop block down, and position fence approximately 90° onto stop cap screw (see Figure 68). Setting 45° Inward Stop 1.
Setting 45° Outward (135°) Stop 1. DISCONNECT MACHINE FROM POWER! 2. Loosen fence tilt lock, rotate stop block up, then tilt fence approximately 45° inward onto stop bolt (see Figure 70). Stop Block 3. Place sliding bevel set to 135° against fence and table, as shown in Figure 71. Sliding Bevel Set to 45° Outward 45° Outward Stop Bolt Jam Nut Figure 71. Example of adjusting fence 45° outward. Tilt Lock Figure 70. Fence set to 45° outward. -50- 4.
Calibrating Depth-of-Cut Scale Calibrating Depth Scale 4. Adjust infeed table until it is even with outfeed table (see Figure 72). G0855 For best cutting results, calibrate or "zero" the depth-of-cut scale so cutting depth shown on the scale matches the actual cutting depth (per pass). Straightedge Outfeed Infeed Item(s) Needed: Qty Precision Straightedge 3'................................... 1 Phillips Screwdriver #2....................................... 1 To calibrate depth-of-cut scale: 1.
Tensioning/ Replacing V-Belt Belts and pulleys will be hot after operation. Allow them to cool before handling. Tensioning Replacing Belt To ensure optimum power transmission from the motor to the cutterhead, the V-belt must be in good condition (free from cracks, fraying and wear) and properly tensioned. 5. Cutterhead Pulley After approximately 16 hours of operation, belts will stretch and seat into pulley grooves.
Checking/Aligning Pulleys Cutterhead Pulley Checking Aligning Pulleys Alignment Pulley alignment is an important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplaner) for optimum performance. Motor Pulley Each pulley can be adjusted by loosening the set screw that secures the pulley to the shaft, sliding the pulley in/out, and retightening the set screw to lock the pulley in place. Figure 77. Proper pulley alignment.
Checking/Adjusting Cutterhead Guard 3. Loosen set screw (see Figure 78) that secures cutterhead guard shaft to table assembly. 4. Lift cutterhead guard so shaft (see Figure 78) clears hole, rotate guard clockwise, then reinstall guard so flat side of shaft faces cap screw and lowest part of guard is not more than 1⁄16" over rabbeting ledge or infeed table. 5. Tighten set screw (see Figure 78). Adjusting Cutterhead Guard The cutterhead guard is a critical safety feature of this jointer.
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
Wiring Diagram Paddle Switch (viewed from behind) ON/STOP Switch KJD17B-230V 14 13 WARNING! 24 23 SHOCK HAZARD! Disconnect power before working on wiring. Ground Ground 230 VAC Hot Motor Run Capacitor 70uF 250VAC Start Capacitor 400uF 125VAC G Hot Ground 6-20 Plug Motor Junction Box Figure 79. On/Stop switch connections. -56- READ ELECTRICAL SAFETY ON PAGE 55! Figure 80. Motor junction box connections. Model G0855/G0856 (Mfd.
SECTION 9: PARTS Fence & Cutterhead (G0855 Only) (G0856 Only) 111 111 132 133 131 136 134 3 4 28 17 25 9 8 9 10 26 26 29 8 63 19 18 12 14 15 20 13 21 22 24 11 40 16 23 40-2 40-3 (G0856 Only) 40-6 37 36 5 39 38 40-5 33 32 35 41 40-4 40-3 40 23 6 27 135 117 2 7 130 5 65 1 40-2 68 30 31 34 31 42 (G0855 Only) 35 36 68 31 41 42 Model G0855/G0856 (Mfd. Since 02/19) BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store.
Tables, Base, Stand & Motor 51 52 53 50 47 57 48 55 49 104 43 48 45 44 47 113 118 46 110 115 101 114 116 59 99 106 66 86-10 86-15 86-11 86-16 86-12 86-16 86-13 86-17 86-14 86-18 85V2 86-7 86-9 14 58 67 70 86 86-6 92 108 107 93 86-5 112 103 100 105 98 54 102 109 56 71 72 64 59 31 62 29 61 60 101 110 82 80 75 73 81 74 126 120 91 77 128 76 129 125 127 124 78 71 123 125 124 88 121 122 97 79 86-4 86-3 86-2 84 69 14 119 137 94 87 89
Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 40-2 40-3 40-4 40-5 40-6 40 40-2 40-3 41 42 43 44 45 46 47 48 49 FENCE TILT LOCK LEVER 1/2-12 FLAT WASHER 13MM STOP BLOCK FENCE CARRIAGE KNOB 3/8-16, D1-5/16, BALL ECCENTRIC SHAFT 3/8-16, 5-1/4L DOWEL PIN 5 X 50 CAP SCREW 1/4-20 X 1-1/4 HEX NUT 1/4-20 SHOULDER BOLT 5/16-18 X 11/16, 3/8 X 1 HEX NUT 1/2-20 THIN FENCE STUD-SE 1/2-20, 1-3/8
Parts List (Cont.) REF PART # DESCRIPTION REF PART # DESCRIPTION 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 111 112 113 KNOB BOLT 6-LOBE 5/16-18 X 3/4 MAG SWITCH KEDU KJD17B-230V-S CAP SCREW 1/2-12 X 1-3/4 SET SCREW 1/4-20 X 1/4 LOCK WASHER 8MM CAP SCREW M8-1.25 X 70 SWITCH PEDESTAL CAP SCREW M8-1.
Labels & Cosmetics 202 Cutterhead exposed between these lines. Failure to keep hands clear of cutterhead will result in serious personal injury. 203 WARNING! 206 Failure to keep hands clear of cutterhead will result in serious personal injury. 204 203 205 To reduce risk of death or serious injury, read manual BEFORE using machine. To get a new manual, call (800) 523-4777 or go to www.grizzly.com. 207 INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
