Use and Care Manual

ManualsBrandsGrizzly Industrial ManualsDust Collector AccessoriesGrizzly Growler Cyclone Separator for Dust Collector

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL G0863

GRIZZLY GROWLER

CYCLONE SEPARATOR

INSTRUCTIONS

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 6/21) #MN20050 PRINTED IN TAIWAN

Introduction

Description Qty

A. Collection Drum .......................................... 1

Cyclone Funnel w/Band Clamp .................. 1

Intake Barrel ............................................... 1

Vacuum Hose 1

⁄2" x 67" ........................... 1

Outlet Reducer 7" x 6" ............................... 1

Collection Drum Lid .................................... 1

Vacuum Ring .............................................. 1

Inlet Adapter 6" x 4" x 2 .............................. 1

Universal Reducer ...................................... 1

Frame Arches ............................................. 2

K. Base Arch ................................................... 1

L. Frame Legs ................................................ 4

M. Connectors ................................................. 6

N. Base Legs .................................................. 2

Open-End Wrench 10/12mm ...................... 1

Hex Bolts

⁄16"-18 x 1

⁄4" (Stand) ................ 32

Flange Nuts

⁄16"-18 (Stand) ...................... 32

Flat Washers

⁄16" (Stand) ......................... 24

Lock Nuts M4-.7 (Latches) ......................... 8

Flange Bolts

⁄4" -20 x

⁄4" (Funnel) ............... 4

Flange Bolts

⁄4" -20 x

⁄2" (Funnel) .............. 2

. Phillips Head Screws M4-.7 x 8 (Latches) . . 8

. Hex Nuts

⁄16" - 1 8 (Stand Casters) ............... 4

Flange Nuts

⁄4" - 2 0 (Funnel) ....................... 6

. Casters, 2" Swivel Ball ............................... 8

. Acorn Nuts

⁄4" -20 (Handle) ........................ 2

. Flange Screws 10-24 x

⁄8"

—Intake Adapter ........................................ 1

—Inlet Adapter ........................................... 1

. Phillips Hd. Screws

⁄4" -20 x

⁄8" (Handle) ... 2

Inventory

V2.01.22

The Grizzly Growler creates a cyclone of incom-

ing air that separates heavy wood chips and large

dust particles, increasing the performance of your

single-stage dust collector, and resulting in less

suction loss from dirty or clogged filters.

. Collection Drum Latches ............................ 2

. Hose Clamps 1

⁄2" ...................................... 2

. Handle ........................................................ 1

. End Caps .................................................... 2

. Plastic Bag 30" x 41" (not shown) ............... 1

Figure 1. Inventory.

A B

F G H I

K L

P Q R S

T U V W X

Y Z

AB AC

Summary of content (8 pages)

PAGE 1
MODEL G0863 GRIZZLY GROWLER CYCLONE SEPARATOR INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction The Grizzly Growler creates a cyclone of incoming air that separates heavy wood chips and large dust particles, increasing the performance of your single-stage dust collector, and resulting in less suction loss from dirty or clogged filters. Inventory Description Qty A. Collection Drum...........................................
PAGE 2
Specifications 2. Recommended Horsepower Range...... 1.5–3 HP Airflow Range.............................. 750–2300 CFM Outlet Size..................................................... 7 in. Inlet Size........................................................ 6 in. Max. Material Collection Capacity.............20 Gal. Align two holes in each connector with two holes in base arch (see Figure 3) and secure with (4) 5⁄16"-18 x 1 1⁄4" hex bolts, 5⁄16" flat washers, and 5⁄16"-18 flange nuts.
PAGE 3
5. Install (1) 5⁄16"-18 hex nut on each of (4) caster wheels, then install wheels on base, as shown in Figure 5. 8. Align two holes in each connector with two holes in frame arch (see Figure 7) and secure with (4) 5⁄16"-18 x 1 1⁄4" hex bolts, 5⁄16" flat washers, and 5⁄16"-18 flange nuts. Only hand-tighten for now. Frame Arch Caster Wheels x4 Connectors Figure 5. Caster wheels installed on base. 6. 7. Position base rightside up, and adjust wheels until base sits level and does not rock.
PAGE 4
10. Repeat Steps 7–9 with remaining (1) frame arch, (2) frame legs, and (2) connectors. 11. Install (2) assembled frames on base (see Figure 9) with (8) 5⁄16"-18 x 1 1⁄4" hex bolts and 5⁄16"-18 flange nuts. Only hand-tighten for now. Note: Assembled frames must be installed with funnel brackets facing each other, as shown in Figure 9. Funnel Bracket (1 of 2) x8 13.
PAGE 5
16. Install (2) collection drum latches with (8) M4-.7 x 8 Phillips head screws and (8) M4-.7 lock nuts (see Figure 13). x4 19. Position collection drum under drum lid, hook drum latches on lid tabs, and press latches down to secure (see Figure 15). Latch (1 of 2) Drum Drum Lid Latch (1 of 2) Figure 13. Latches installed on collection drum. Figure 15. Collection drum secured against lid. 17. Place vacuum ring inside collection drum with smaller side of ring facing down, as shown in Figure 14. 20.
PAGE 6
22. Install inlet adapter on dust port and secure with 10-24 x 3 ⁄ 8" flange screw (see Figure 17). 25. Route a dust hose from dust collector inlet (see Figure 20) to outlet on Grizzly Growler intake barrel. Then route a dust hose from Growler inlet to machine dust port. Secure both hoses with clamps. Outlet Inlet Adapter Inlet x1 Figure 17. Installing inlet adapter on dust port. To Machine Dust Port 23. Install outlet reducer (see Figure 18) on intake barrel with 10-24 x 3 ⁄ 8" flange screw.
PAGE 7
G0863 Parts Breakdown 5 24 30 30 4 6 22 28 39 2 40 38 37 29 23 23 31 20 13 16 7 55 7 55 35 55 55 14 42 18 3 32 15 17 6 43 21 41 1 19 10 54 8 46 48 9 47 50 11 45 53 52 49 51 42 44 36 33 34 Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability. G0863 Grizzly Growler (Mfd.
PAGE 8
G0863 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 28 29 30 COLLECTION DRUM COLLECTION DRUM LID CYCLONE FUNNEL INTAKE BARREL OUTLET REDUCER 7" X 6" HOSE CLAMP 1-1/2" FLANGE BOLT 1/4-20 X 1/2 HANDLE PHLP HD SCR 1/4-20 X 5/8 ACORN NUT 1/4-20 CASTER 2" SWIVEL BALL BAND CLAMP 45" LOCK NUT M4-.7 PHLP HD SCR M4-.