MODEL G1066R/G1066Z/G1079R DRUM SANDER OWNER'S MANUAL (For models manufactured since 02/11) Model G1066Z Model G1066R Model G1079R COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC. REVISED OCTOBER, 2018 (ES) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #0443 PRINTED IN TAIWAN V2.10.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Contact Info.................................................... 2 Machine Differences....................................... 2 Manual Accuracy............................................ 2 Identification (G1066R)................................... 3 Identification (G1066Z)................................... 4 Identification (G1079R)................................... 5 Controls & Components..................................
INTRODUCTION Contact Info Manual Accuracy We stand behind our machines! If you have questions or need help, contact us with the information below. Before contacting, make sure you get the serial number and manufacture date from the machine ID label. This will help us help you faster. We are proud to provide a high-quality owner’s manual with your new machine! Grizzly Technical Support 1815 W. Battlefield Springfield, MO 65807 Phone: (570) 546-9663 Email: techsupport@grizzly.
Identification (G1066R) Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Outfeed (Rear) Sanding Drum Infeed (Front) Sanding Drum 4" Dust Ports Top Cover Table Height Crank Handle Conveyor Table w/Belt On/Off Switch Front Access Panel Rear Access Panel To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model G1066R/Z/G1079R (Mfd.
Identification (G1066Z) Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Outfeed (Rear) Sanding Drum Micro-Adjustment Lock Lever Micro-Adjustment Knob Infeed (Front) Sanding Drum Table Height Crank Handle 4" Dust Ports Control Panel Top Cover Conveyor Table w/Belt Front Access Panel Rear Access Panel To reduce your risk of serious injury, read this entire manual BEFORE using machine.
Identification (G1079R) Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Infeed (Front) Sanding Drum Outfeed (Rear) Sanding Drum Table Height Crank Handle Top Cover 4" Dust Ports Conveyor Table w/Belt On/Off Switch Front Access Panel Stand Rear Access Panel To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model G1066R/Z/G1079R (Mfd.
Controls & Components C. Table Height Crank Handle: Rotate to raise or lower conveyor table according to workpiece thickness. D. Conveyor Table w/Belt (Infeed End): Height-adjustable table with conveyor belt that feeds workpieces toward sanding drums. To reduce your risk of serious injury, read this entire manual BEFORE using machine. E F G H I G1066R Refer to Figures 45–47 and the following descriptions to become familiar with the basic controls and components of the Model G1066R.
G1066Z F. Refer to Figures 48–50 and the following descriptions to become familiar with the basic controls and components of the Model G1066Z. Understanding these items and how they work will help you understand the rest of the manual and stay safe when operating this machine. A B C Table Height Crank Handle: Rotate to raise or lower conveyor table according to workpiece thickness. G. Depth-of-Cut Scale: Indicates distance between conveyor table and sanding drums. H.
G1079R Refer to Figures 51–53 and the following descriptions to become familiar with the basic controls and components of the Model G1079R. Understanding these items and how they work will help you understand the rest of the manual and stay safe when operating this machine. E. Depth-of-Cut Scale: Indicates distance between conveyor table and sanding drums. F. Conveyor Table w/Belt (Infeed End): Height-adjustable table with conveyor belt that feeds workpieces toward sanding drums.
Machine Data Sheet (G1066R) MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G1066R 24" DRUM SANDER Product Dimensions: Weight.............................................................................................................................................................. 389 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 37 x 34-1/2 x 43 in.
Main Specifications: Operation Information Number of Sanding Heads............................................................................................................................... 2 Maximum Board Width........................................................................................................................ 23-1/2 in. Minimum Board Width................................................................................................................................. 2 in.
Machine Data Sheet (G1066Z) MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G1066Z 24" DRUM SANDER W/ VS Product Dimensions: Weight.............................................................................................................................................................. 389 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 50 x 37 x 44-1/2 in.
Main Specifications: Operation Information Number of Sanding Heads............................................................................................................................... 2 Maximum Board Width........................................................................................................................ 23-1/2 in. Minimum Board Width................................................................................................................................. 2 in.
Machine Data Sheet (G1079R) MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G1079R 16" DRUM SANDER W/ RUBBER CONVEYOR Product Dimensions: Weight.............................................................................................................................................................. 283 lbs. Width (side-to-side) x Depth (front-to-back) x Height...............................................................
Main Specifications: Operation Information Number of Sanding Heads............................................................................................................................... 2 Maximum Board Width........................................................................................................................ 15-3/8 in. Minimum Board Width................................................................................................................................. 2 in.
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts. HAZARDOUS DUST. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material.
Additional Safety for Drum Sanders Serious injury or death can occur from getting hands trapped between workpiece and conveyor table and being pulled into machine, or becoming entangled in rotating parts inside machine. Workpieces thrown by sander can strike nearby operator or bystanders with significant force. Long-term respiratory damage can occur from using sander without proper use of a respirator.
SECTION 2: POWER SUPPLY Power Supply Availability Circuit Requirements for 220V Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed.
Grounding Instructions This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. The power cord and plug specified under “Circuit Requirements for 220V” on the previous page has an equipment-grounding wire and a grounding prong.
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! HEAVY LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.
Inventory Site Considerations The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used.
Lifting & Placing HEAVY LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine. DO NOT attempt to lift or move machine without using a forklift or necessary assistance from other people. Review the Power Supply section (Page 18) and Site Considerations section (Page 21), then prepare a permanent location for the machine.
Assembly 3. The machine must be fully assembled before it can be operated. Before beginning the assembly process, refer to Needed for Setup and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if applicable). Attach crank handle (see Figure 58) to leadscrew shaft and secure with (2) preinstalled set screws.
5. Dust Collection G1066Z Only: Attach front panel to machine base with (8) #8 x 3⁄8" self-tapping screws, as shown in Figure 60. Front Panel This machine creates a lot of wood chips/ dust during operation. Breathing airborne dust on a regular basis can result in permanent respiratory illness. Reduce your risk by wearing a respirator and capturing the dust with a dust-collection system. Self-Tapping Screws (1 of 8) Figure 60. Diagram of front panel and screw locations.
Test Run Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix the problem BEFORE operating the machine again. The Troubleshooting table in the SERVICE section of this manual can help. G1066Z For Model G1066Z, the Test Run verifies the following: 1) The motors power up and run correctly.
6. — If conveyor belt runs smoothly, proceed to Step 7. — If conveyor belt does not run smoothly, immediately turn machine OFF and call Tech Support for help. 7. 8. Recommended Adjustments Push Conveyor Motor ON button to turn motor ON. A correctly operating machine will run smoothly with little or no vibration or rubbing noises. Push Emergency Stop button to turn machine OFF. WITHOUT resetting Emergency Stop button, press Sanding Drum Motor ON button and Conveyor Motor ON button.
Disabling & Locking Switch (G1079R) The ON/OFF switch can be disabled and locked by inserting a padlock through the ON button, as shown. Locking the switch in this manner can prevent unauthorized operation of the machine, which is especially important if the machine is not stored inside an access-restricted building. IMPORTANT: Locking the switch with a padlock only restricts its function. It is not a substitute for disconnecting power from the machine when adjusting or servicing.
SECTION 4: OPERATIONS Operation Overview To reduce your risk of serious injury, read this entire manual BEFORE using machine. Eye injuries, respiratory problems, or hearing loss can occur while operating this tool. Wear personal protective equipment to reduce your risk from these hazards. Keep hair, clothing, and jewelry away from moving parts at all times.
Stock Inspection and Requirements • Excessive glue or finish: Sanding workpieces with excess glue or finish will load up the abrasive, reducing its usefulness and lifespan. Stock Inspection • Minimum Stock Dimensions: DO NOT sand boards less than 9" long, 2" wide, and 1⁄8" thick (G1066R/G1066Z) or 1⁄4" thick (G1079R) to prevent damage to the workpiece and to reduce the risk of your hands contacting the abrasive belt (see Figure 66).
The general rule of thumb is to sand a workpiece with progressively higher grit numbers, with no one grit increase of more than 50. Avoid skipping grits; the larger the grit increase, the harder it will be to remove the scratches from the previous grit. The Model G1066R/G1066Z/G1079R allows you to place a different grit sandpaper on each drum. The front drum should have a coarser grit than the rear. Usually this translates into combinations of successive group types.
Sanding Setting Depth of Cut Setting Depth of Cut DO NOT sand more than one board at a time. Minor variations in thickness can cause one board to be propelled by the rapidly spinning sanding drum and ejected from the machine. NEVER stand directly in front of the outfeed area of the machine. Failure to do so could result in severe personal injury. To sand a workpiece: 1. Adjust table height (refer to Setting Depth of Cut on This Page.) 2.
Setting Conveyor Speed (G1066Z) Setting Conveyor Speed The conveyor speed control allows you to set the conveyor speed from 0–10 (0–20 FPM). The correct speed to use depends on the type of stock you are using (hardwood vs. softwood) and the stage of finish you are at with that workpiece. As a general rule, a slower speed will sand the surface smoother, but runs the risk of burning the wood; a faster speed will remove material faster, but runs the risk of overloading the motor.
Installing/Replacing Sandpaper (G1066R/ G1079R) 4. Tip: Note direction sandpaper was wrapped around drum. Installing Sandpaper G1066R The Model G1066R/G1079R is designed for 6" wide sandpaper rolls. The sandpaper roll attaches to the sanding drums with a spring clip on one end and strapping tape on the other end of the drum. The outfeed sanding drum is wrapped in felt to slightly increase the drum diameter and to provide a smooth sanded surface.
8. Hold loose end of sandpaper against right side of drum and wrap with strapping tape to secure. Double-check drum to make sure there are no bubbles or overlapping edges and gapping is correct. 9. Repeat Steps 1–8 for second drum. 3. Tip: Note direction sandpaper was wrapped around drum. 10. Close/re-install top cover. Make sure dustcollection hoses are secure. Important Tips For Changing Sandpaper: 18" Replace sandpaper on each drum individually.
SECTION 5: ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. Model D3003—PRO-STIK® Cleaning Pad Extend the life of your sandpaper! Just feed this crepe-rubber cleaning pad through your drum sander to remove dust build-up from the sandpaper without damage. Measures 15" x 20" x 11⁄8".
D4206—Clear Flexible Hose 4" x 10' D4256—45° Elbow 4" D4216—Black Flexible Hose 4" x 10' W1034—Heavy-Duty Clear Flex Hose 4" x 10' D2107—Hose Hanger 4 1⁄4" W1015—Y-Fitting 4" x 4" x 4" W1017—90° Elbow 4" W1019—Hose Coupler (Splice) 4" W1317—Wire Hose Clamp 4" W1007—Plastic Blast Gate 4" W1053—Anti-Static Grounding Kit We've hand picked a selection of commonly used dust collection components for machines with 4" dust ports. D4206 H3631 H3635 D4216 Figure 78.
SECTION 6: MAINTENANCE Cleaning To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Cleaning the Model G1066R/G1066Z/G1079R is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Schedule For optimum performance from this machine, this maintenance schedule must be strictly followed.
SECTION 7: SERVICE Review the troubleshooting procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Machine does not start or a breaker trips. 1. Emergency Stop button depressed/at fault (G1066Z). 2.
Operation Symptom Possible Cause Possible Solution Machine slows when sanding; makes squealing noise on start-up. 1. Belt(s) loose or worn. 1. Tension/replace belt(s) (Page 45). Grinding, screeching, or rubbing noise from sanding drums. 1. Drum scraping on dust scoop. 2. Drum bearings need grease. 3. Drum bearings worn. 1. Adjust dust scoop so it does not contact drum (Page 44). 2. Grease drum bearings (Page 29). 3. Replace drum bearings (Page 47).
Aligning Drums Drum Alignment For the Model G1066R/G1066Z/G1079R Drum Sander to function properly, the sanding drums must be aligned in two directions: (1) perpendicular to feed direction (see Figure 81) and (2) parallel to the conveyor belt (see Figure 82). Adjusting Sanding Drums Perpendicular to Feed Direction Item(s) Needed Qty Tape Measure..................................................... 1 Open-End or Socket Wrench 9 ⁄ 16"..................... 1 Adjusting Sanding Drums Perpendicular 1.
5. Tighten lock nuts and recheck alignment. 9. Note: DO NOT over tighten lock nuts. Bearing blocks will break if over tightened. Adjusting Sanding Drums Parallel to Feed Belt Item(s) Needed Qty 2x4 Gauge Block (2" x 4" x 24")......................... 1 Marking Tape or Felt Pen................................... 1 Open-End or Socket Wrench 9 ⁄ 16"..................... 1 10. Lower table (1⁄8) turn from Reference Height #1 and mark location of crank handle and table in relation to the body of sander.
2. Raise or lower bearing block by rotating set screws (see Figure 84). Turn very gradually—1⁄8 turn or less. 3. Tighten lock nuts and re-check alignment using gauge block. Note: Tightening lock nuts pulls sanding drum slightly downward. Re-adjust set screws as necessary to compensate for this movement. DO NOT over tighten lock nuts. Bearing blocks will break if over tightened. Also, DO NOT change table height until the lock nuts are tight. Repeat Steps 1–3 on other side of drum. 4.
Note: Increasing pressure roller tension will increase workpiece pressure on the conveyor belt. Increasing this pressure could increase the likelihood of jams and make the sanding process less forgiving of irregularities in the workpiece. Experiment to determine optimal tension for your workpieces. 4. Item(s) Needed Qty 2x4 Gauge Block (2" x 4" x 24")......................... 1 Phillips Screwdriver #2.......................................
4. Adjusting Dust Scoop Make conveyor belt tension and tracking adjustments: — If belt slips on rollers, rotate both roller adjustment bolts (see Figure 87) counterclockwise to increase belt tension. Roller Bracket Roller Adjustment Bolt (1 of 2) Figure 87. Location of conveyor roller adjustment bolts. — If belt tracks toward right, rotate right-side roller adjustment bolt counterclockwise to move belt left.
Tensioning/ Replacing V-Belts Item(s) Needed Qty Open-End or Socket Wrench 17mm................... 1 Straightedge (at least 24").................................. 1 Tape Measure..................................................... 1 Phillips Screwdriver #2....................................... 1 Hex Wrench 5mm............................................... 1 V-Belt V-Belt Tension Tension New V-belts often stretch and loosen up during the first 16 hours of use.
6. Check V-Belt tension. If necessary, repeat Steps 3–5 until belt(s) is properly tensioned. 7. Re-install right access panel. Removal/Replacement Replace the V-belt if you notice fraying, cracking, glazing, or any other damage. A worn/damaged V-belt will not provide optimum power transmission from the motor to the drums. V-belt removal and replacement is simply a matter of loosening the V-belts until you can roll them off the pulleys, replacing them with a MATCHED set, then re-tensioning them.
Replacing Bearings Bearing Replacement The Model G1066R/G1066Z/G1079R is designed for many years of reliable service. But after long periods of heavy use, it may be necessary to replace the pillow block bearings. Always replace both bearings on the same drum at the same time. Make sure, when installing the new bearing, that lubrication groove in the bearing will match groove and grease fitting in housing once it is in place. Item(s) Needed Qty Large, Round-Shaft Screwdriver........................
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
G1066R Electrical Components Figure 96. G1066R drum motor connections. Figure 94. G1066R magnetic switch connections. Figure 97. G1066R drum motor capacitors. Figure 95. G1066R feed motor connections and capacitor. Model G1066R/Z/G1079R (Mfd.
G1066R Wiring Diagram Ground X Hot G Y Hot 220 VAC L6-30 PLUG (As Recommended) WARNING! SHOCK HAZARD! A Disconnect power before working on wiring.
G1066Z Electrical Components Figure 98. G1066Z feed motor connections and capacitors. Figure 99. G1066Z controls connections (rotated 90°). Figure 100. G1066Z control panel connections. Model G1066R/Z/G1079R (Mfd.
G1066Z Wiring Diagram 3 6 NHD CB-10 5 NHD CB-10 2 2 5 GND NHD CB-01 1 − + NHD CB-01 1 NHD CB-01 GND T T 2 T T 21 L1/1 L2/3 L3/5 MA-09 5 Feed Motor 7 MA-30 R1 T1 T1/2 3 T2/4 T3/6 8 Motor Junction Box T1 6 R1 GND Circuit Board 22 U W RA-30 T + U − W GND Run Capacitor 50uF 350VAC Start Capacitor G Y X Hot Hot 220 VAC L6-30 PLUG 600MFD 125VAC Drum Motor Ground -52- READ ELECTRICAL SAFETY ON PAGE 33! Model G1066R/Z/G1079R (Mfd.
G1079R Electrical Components Figure 103. G1079R drum motor connections. Figure 101. G1079R switch and circuit breaker connections. Figure 104. G1079R drum motor start capacitor. Figure 102. G1079R feed motor connections and run capacitor. Model G1066R/Z/G1079R (Mfd.
G1079R Wiring Diagram FEED MOTOR R Capacitor 12uF 350VAC Ground WARNING! SHOCK HAZARD! Disconnect power before working on wiring. ON/OFF SWITCH (viewed from behind) NO FFO DRUM MOTOR THERMAL CIRCUIT BREAKER Ground Ground G Start Capacitor Ground 400MFD 125VAC (viewed from behind) Hot 220 VAC Hot -54- 6-20 Plug (As Recommended) READ ELECTRICAL SAFETY ON PAGE 33! Model G1066R/Z/G1079R (Mfd.
SECTION 9: PARTS G1066R Stand & Table Elevation 204 140 13 139 139 13 140 14 202 205 204 12 11 202 101 205 20-1 10 20-5 20-2 15 20-5 20-3 8-1 8-1 20-6 20-4 20-7 8 8-1 8-1 8 102 29 6 8-1 5 4 7-1 7 6 5 7-1 7 20 117 17 2 19 106 107 6 5 8 6 207 209 32 208 9 109 203 33 37 34 2 24 22 8-1 7-1 7 200 5 3 91 90 18 8-1 8-1 8 3 106 107 30 2 208 156 124 102 31 155 29 1 23 16 4 22 24 2 29 116 29 Model G1066R/Z/G1079R (Mfd.
G1066R Conveyor Belt & Table 53 66 62 137 64 69 58 201 54 59 51 60 61 35V2 35V2 137 50 61 62 60 64 36 62 51V2 51 60 61 50 35V2 64 137 49 38 51 40 41 58 64 137 67 39-2 150 47 151 29 152 43 62 39-3 59 61 60 39-4 46 48 35V2 65 58 39-1 68 206 39 153 45 44 42 154 -56- BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. Model G1066R/Z/G1079R (Mfd.
G1066R Drum & Roller Mechanism 92 92 107 125 125 89 55 115 83 86 86 85 79 83 86 86 85 85 79 82 93 97 81 105 82 62 94 95 93 94 95 62 89 106 88 93 105 125 125 89 62 73 55 115 70 88 71 88 73 73 93 88 107 85 97 81 99 89 106 70 62 71 76 77 87 78 88 73 73 70 98 72 85 76 62 88 73 62 77 78 86 86 85 81 78 87 78 86 85 86 81 85 79 83 83 79 97 105 82 97 105 82 Model G1066R/Z/G1079R (Mfd. Since 02/11) BUY PARTS ONLINE AT GRIZZLY.
G1066R Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 7-1 8 8-1 9 10 11 12 13 14 15 16 17 18 19 20 20-1 20-2 20-3 20-4 20-5 20-6 20-7 22 23 24 29 30 31 32 33 34 35V2 36 37 38 39 39-1 39-2 39-3 39-4 40 41 42 43 44 45 46 47 FRAME HEX NUT 3/8-16 FLAT WASHER 3/8 SIDE PANEL BUSHING SPROCKET SPROCKET SHAFT TABLE SCREW FINE THREADS 3/4-16 TABLE SCREW SHIM 1/2 X 27 X 1 CHAIN FRONT BRACE SET SCREW 5/16-24 X 3/8 COMPLETE CRANK HANDLE ASSY DUST HOOD HOOD REAR BRACE REAR PANEL SET SCREW 1/4
G1066R Parts List (Cont.
G1066Z Stand & Table Elevation 285 139 141 266 80 140 34 285 266 139 34 140 149 14 138 13 276 273 29 147 141 20-1 263 12 20-2 20-3 20-6 101 25 25 11 263 20-4 20-7 281 29 102 8-1 8-1 8 79 6 5 17 19 91 90 18 53 21 22 23 8-1 8-1 8 6 5 7-1 7 7-1 7 23 29 24 22 26 27 16 37 118 32 119 120 143 288 9 277 3 2 1 22 34 29 2 148 4 102 281 29 220 29 28 221 259 77 78 126 136 227 -60- 8-1 8-1 8 6 5 106 107 106 107 29 239 287 22 2 8-1 8-1 7-1 7 8 6 5 278 265 15 20-5 20 29 147 10
G1066Z Conveyor Belt & Table 52 66 69 137 74 58 58 144 64 51 60 59 58 58 35 137 50 72 61 35 60 61 64 36 74 51 51 60 61 59 38 74 64 55 65 61 60 51 35 271 63 62 269 274 35 270 21 21 67 64 74 59 68 49 40 46 48 40 41 58 58 137 58 58 47 29 239 29 244 125 137 246 45 44 142 42 39 43 Model G1066R/Z/G1079R (Mfd. Since 02/11) BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store.
G1066Z Drum & Roller Mechanism 242 242 238 240 214 212 34 34 254 280 242 212 34 254 247 243 201 204 206 282 245 207 267 248 216 202 268 202A 283 275 86 85 106 286 125 89 279 86 85 93 88 74 89 125 96 75 105 107 88 93 94 95 82 81 86 85 84 93 93 94 97 95 73 74 86 85 81 92 107 74 106 125 89 73 75 105 70 88 88 71 73 70 74 86 85 71 88 73 73 70 88 98 89 125 73 74 74 86 85 97 86 85 81 97 81 BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store.
G1066Z Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 7-1 8 8-1 9 10 11 12 13 14 15 16 17 18 19 20 20-1 20-2 20-3 20-4 20-5 20-6 20-7 21 22 23 24 25 26 27 28 29 30 31 32 33V2 34 35 36 37 38 39 40 41 42 43 44 FRAME HEX NUT 3/8-16 FLAT WASHER 3/8 SIDE PANEL FLAT WASHER 1/2 SPROCKET SPROCKET SHAFT TABLE SCREW FINE THREADS 3/4-16 TABLE SCREW SHIM 1/2 X 27 X 1 CHAIN FRONT BRACE SET SCREW 5/16-24 X 3/8 COMPLETE CRANK HANDLE ASSY DUST HOOD HOOD REAR BRACE REAR PANEL SET SCREW 1/4-20 X
G1066Z Parts List (Cont.
G1079R Stand & Table Elevation 139 140 140 179 13 13 14V2 156 150 157 179 157 101 152 157 178 157 12 153 178 157 11 139 151 154 155 205 15V2 208 10 55 4 29 8-1 8-2 8 8-1 8-2 8-1 8-2 8 7-1 7 6 5 6 162 177 161 160 168 166 165 100 167 175 167 165 33V2 105 104 174 162 159 162 160 161 161 160 7 162 161 160 5 7-1 3 160 161 161 160 6 5 6 5 158 8-1 8-2 177 8 8 9 2 16V2 23 25 23 40 34 29 1 4 55 29 40 34 29 168 116 176 17 18 17 21 19 22 24 20-1 32V2 31V2 149 Model
G1079R Conveyor Belt & Table 53 66 69 74 137 58 58 203 164 58 58 51V2 137 64 140 161 137 61 60 51V2 137 36 63 35 64 74 35 59 60 61 74 64 137 65 59 49 40 51V2 38 61 67 39-4 39-3 BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. 137 58 58 68 204 137 58 58 137 46 48 40 41 137 74 39-2 50 60 64 -66- 61 35 35 39-1 60 51V2 56 29 47 181 182 183 45 39 118V2 180 44 42 43 Model G1066R/Z/G1079R (Mfd.
G1079R Drum & Roller Mechanism 91 92 99 23 89 25 84 84 89 90 26 83 86 86 85 79 83 86 86 79 81 27 108 97 81 82 27 85 94 93 82 108 94 93 74 74 84 84 89 74 73 90 26 70 88 71 88 73 73 70 108 88 89 25 88 108 97 85 85 23 74 71 76 77 87 78 88 73 73 70 98 72 85 76 74 88 73 74 77 78 86 86 85 81 78 87 78 86 85 86 81 85 79 83 83 79 97 82 27 97 82 27 Model G1066R/Z/G1079R (Mfd. Since 02/11) BUY PARTS ONLINE AT GRIZZLY.
G1079R Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 7-1 8 8-1 8-2 9 10 11 12 13 14V2 15V2 16V2 17 18 19 20 20-1 20-2 20-3 20-4 20-5 21 22 23 24 25 26 27 29 31V2 32V2 33V2 34 35 36 38 39 39-1 39-2 39-3 39-4 40 41 42 43 44 45 46 FRAME HEX NUT 3/8-16 FLAT WASHER 3/8 SIDE PANEL BUSHING SPROCKET SPROCKET SHAFT TABLE SCREW 3/4-16 TABLE SCREW SHIM 1/2 X 27 X 1 TABLE SCREW SHIM 1/2 X 28 X 3 ELEVATION CHAIN FRONT BRACE SET SCREW 1/4-20 X 1/2 COMPLETE CRANK HANDLE ASSY DUST PORT HOOD V
G1079R Parts List (Cont.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
