READ THIS FIRST Model G9729 ***IMPORTANT UPDATE*** For Machines Mfd. Since 4/18 and Owner's Manual Revised 9/13 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com The following changes were recently made since the owner's manual was printed: • Parts revised to show new motor. Motor specs updated. Aside from this information, all other content in the owner's manual applies and MUST be read and understood for your own safety.
Revised Specifications Electrical: Full-Load Current Rating. .......................................................................................................................................... 8.5A Motors: Lathe Spindle Amps....................................................................................................................................................................... 8.5A Speed. .....................................................................................................
COMBINATION LATHE/MILL MODEL G9729 INSTRUCTION MANUAL COPYRIGHT © MAY, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED SEPTEMBER, 2013 (ST) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
Table of Contents INTRODUCTION................................................................................................................................ 3 Foreword..................................................................................................................................... 3 Contact Info................................................................................................................................. 3 Machine Data Sheet............................................
Half Nut..................................................................................................................................... 38 Apron Power Feed.................................................................................................................... 38 Changing Gears........................................................................................................................ 39 Inch Threading...............................................................................
INTRODUCTION Foreword Contact Info We are proud to offer the Model G9729 Combination Lathe/Mill. This machine is part of a growing Grizzly family of fine metalworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. If you have any comments regarding this manual, please write to us at the address below: We are pleased to provide this manual with the Model G9729.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G9729 COMBO LATHE/MILL Design Type: Bench Model Overall Dimensions: Overall Length...........................................................................................................58" Overall Width.......................................................................................................... 401⁄2" Overall Height ............................................................
Identification C B A D E AE F AC AD G U Y V AB H AA I T X Z W J M N K L S O Q P R Figure 1. G9729 Controls and features. A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Fine Downfeed Handle Quill Downfeed Lever Upper Belt Guard Head Stock Mill/Drill Motor Head Locks Power Indicator ON Switch Emergency Stop Reversing Switch—Lathe Feed Lever Feed Rate Selection Lever Leadscrew Gear Rack Cross Slide Handwheel Longitudinal Handwheel G9729 Combination Lathe/Mill Q.
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. 10. NEVER LEAVE WHEN MACHINE IS RUNNING.
Additional Safety Instructions for Lathe/Mills 1. AVOID CRASHES. Make sure no part of tool, tool holder, compound or cross slide, or carriage will come into contact with the chuck during operation. 2. PRE-START. Before starting the machine be certain the workpiece has been properly engaged in the chuck and tailstock center (if in use) and that there is adequate clearance for full rotation. 3. 4. 5. HOLDING TOOLS. Adjust tool holder to provide proper support for the turning tool you will be using.
Glossary Of Terms The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this lathe/mill and metalworking in general. Become familiar with these terms for assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly! Arbor: A machine shaft that supports a cutting tool. Backlash: Wear in a screw or gear mechanism that may result in slippage, vibration, and loss of tolerance.
SECTION 2: CIRCUIT REQUIREMENTS 110V Operation Electrocution or fire could result if this machine is not grounded correctly or if your electrical configuration does not comply with local and state codes. Ensure compliance by checking with a qualified electrician! Serious personal injury could occur if you connect the machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so.
SECTION 3: SET UP Set Up Safety This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire set up process! The Model G9729 has a shipping weight of approximately 692 lbs. Serious personal injury may occur if safe moving methods are not followed.
Inventory After all the parts have been removed from the two boxes, you should have the following items: A Box 1: (Figure 3) Qty A. Model G9729 Combo Lathe/Mill.................. 1 B. Face Plate................................................... 1 C. Adaptor Plate............................................... 1 Small Box Contents: D. 120T/127T Combo Gear, & 72T Gear........ 1 E. 36T Gear, & 33T Gear................................ 1 F. 30T Gear, & 27T Gear................................ 1 G.
Hardware Recognition Chart 5mm G9729 Combination Lathe/Mill -13-
The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For optimum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated.
Moving & Placing Base Unit The Model G9729 requires the use of lifting equipment such as a fork lift, engine hoist or boom crane. DO NOT lift the machine by hand. Holes are provided in the edge of the lathe bed for inserting 3⁄4" steel rods for lifting (see Figure 5). Used in conjunction with lifting straps and following safe lifting procedures as detailed by the manufacturers of these lifting devices, the lathe/ mill can be safely lifted off the pallet and placed on a sturdy work bench.
Hand Crank Handwheels The hand crank for the longitudinal manual feed must be installed. The apron and cross slide handwheel handles must be installed. A screwdriver is supplied for this job. Locate the threaded holes on each hand wheel and attach the handles (see Figure 7). To install the hand crank: 1. The end of the leadscrew has a washer and screw attached. Remove these. 2. The hand crank has a key slot on one side as shown in Figure 6.
Steady and Follow Rest Removal Follow Rest Removed The Model G9729 Lathe/Mill comes equipped with a steady rest and follow rest. These are used to support smaller stock while turning, drilling or boring. They are installed at the factory for shipping purposes and should be removed at this time. The steady rest has a single clamp bolt that once removed, allows the clamp shoe to come out the side (Figure 8) and the main body to be lifted off of the lathe bed.
Test Run Inspect your machine for loose nuts and bolts, and ensure no tools are left in or around the machine before connecting power. Failure to do this may result in personal injury. Now that the lathe/mill is set up and you have read the safety guidelines, it’s time to give each motor a test run. The purpose of the test run is to make sure the lathe/mill is wired correctly and the motors are working properly before proceeding with additional set up.
SECTION 4: LATHE OPERATIONS Operation Safety Control Panel It is vital that you become familiar with the control panel before operating the Model G9729. Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Power to the two motors is controlled through a series of switches mounted on the Lower and Upper Belt Guards in Figure 9.
Lathe Chuck Removal ALWAYS place a piece of plywood over the bed-ways of the lathe before removing or installing a lathe chuck. This helps by covering the sharp corners of the bed, protecting your hands and fingers from a pinch injury. Always disconnect the power to the machine before making adjustments, set-up changes or cleaning. Failure to do so could result in injury to yourself and others. Chuck and back plate join here. Socket head cap screw Figure 10. Removing screw from back of chuck.
Lathe Chucks with Mounting Plate The Model G9729 Lathe/Mill comes equipped with a 5'' 3-jaw chuck (already installed). The 3-jaw chuck is a scroll-type chuck, meaning that all three jaws move simultaneously when the chuck key is turned. Most 4-jaw chucks, on the other hand, feature jaws that are adjusted independently. A 4-jaw chuck can be used to hold square or rectangular stock and is used to “dial in” stock to true axial alignment. Rotate the chuck key clockwise, closing the jaws (Figure 11).
Chuck Jaws The 3-jaw chuck supplied with the lathe/mill comes with 2 sets of jaws which are depicted in Figure 12. These are commonly known as the internal and external jaws. While both can hold a workpiece on the inside or outside surface of the jaw, the most common uses are shown in Figure 13. Internal Jaw External Jaw Internal Jaw Figure 13. Workholding options. Internal Jaw External Jaw Figure 12. Jaws for the 3-jaw chuck.
Replacing Jaws Changing jaws on the 3-jaw chuck is straight forward, but attention must be paid to the sequence in which the jaws are loaded into the chuck. Follow the instructions below. Lead Thread Always disconnect the power to the machine before making adjustments, set-up changes or cleaning. Failure to do so could result in injury to yourself and others. Figure 14. Arrow points to the lead of the scroll. To replace the jaws: 1. Unplug the lathe/mill! 2.
Face Plate 6. Check your centerline, as tightening the clamps may have caused it to move. Adjust as necessary. The face plate supplied with the model G9729 Lathe/Mill can be easily mounted to the spindle once the chuck has been removed. Installing the faceplate follows the same steps as any of the lathe chucks. In Figure 15 the face plate is being set up to hold a workpiece for precision boring. Always use a minimum of 3 independent clamps when holding eccentric workpieces. 7.
Dead Center The dead center is used to support stock that is too long to be supported by the chuck alone. Stock protruding more than 21⁄2 times its diameter should be supported by a dead or live center. Insert the end of the dead center into the tailstock bore until it seats. The force of the dead center contacting a mounted workpiece will fully seat the taper when the handwheel is tightened.
Tool Post 1 5 The Model G9729 comes supplied with a 4-way turret tool post that is designed to accept up to four 1⁄2" tool bits. Other devices and holders may be installed into the tool post and arranged as in Figure 18. • • When more than one tool is secured into the tool post, changing from one tool to another is quickly done by loosening the lock lever (#4) and rotating the post to the desired tool. A spring-loaded catch is installed below the tool post and allows motion in only one direction.
Tailstock Controls Tailstock Figure 20 shows the locations of the tailstock controls. The tailstock on the Model G9729 is aligned with the headstock at the factory. However, we recommended that you take the time to ensure that the tailstock is aligned to your own desired tolerances. 1. Tailstock Handwheel Turning the handwheel advances or retracts the quill in the tailstock. The graduated dial on the handwheel is adjustable. To align the tailstock: 1.
Adjust the cutter half the distance of the taper. Lathe Dog Figure 24. Adjusting for tailstock end taper. Figure 22. Bar stock mounted between centers with lathe dog. Adjust the cutter half the distance of the taper. 7. Loosen the four tailstock mounting bolts. Adjust the tailstock offset by half the amount of the taper by turning the adjustment set screws (Figure 25). Turn another .010'' off of the stock and check for a taper. Repeat as necessary until the desired amount of accuracy is achieved.
Tailstock Drill Mounting Tailstock Drill Removal Prior to mounting the drill chuck into the tailstock, wipe the inside of the tailstock quill and arbor down with a clean dry cloth and inspect them for nicks or scratches. Any irregularities on the surface of the arbor or inside the tailstock quill will hinder the locking capability of the taper and should be dressed smooth with a fine file. Then wipe down with your hand to finish the cleaning process.
Carriage Controls The lathe has 3 handles for manual control of the tool bit during machining operations. Compound Slide This slide is adjustable so that cuts may be produced with an angle. By loosening the bolts at the swivel base as shown in Figure 27, the compound may pivot to any angle relative to the turning axis of the lathe spindle. This feature allows tapered cuts to be produced on a workpiece.
Carriage Lock The carriage lock lever is located under the right hand side of the apron as shown in Figure 29. This allows the carriage to be locked in place for precision facing operations while using the lathe or to make a set up in a milling operation more rigid. Figure 29. Carriage lock.
Follow Rest 4. Lubricate the brass finger surfaces with oil prior to seating them on the workpiece and occasionally during use. The follow rest is used on long narrow stock to help keep deflection to a minimum. In normal use, the cutter applies some pressure to the part. In the case of slender parts (even those supported by a center mounted in the tailstock) there is a tendency for the part to deflect away from the cutter.
Steady Rest 3. Loosen the thumb screws for each brass finger and adjust the brass fingers to allow plenty of clearance for the workpiece. The steady rest is used for the same reasons as the follow rest and also when support is needed for a workpiece that cannot be supported by a center in the tailstock. This is especially useful when the end of a long workpiece is to be faced (Figure 32). 4. Loosen the knurled thumb wheel, and pivot the head out of the way (see Figure 33). 5.
Lathe Speeds The speed of the lathe is controlled by the positions of the belts on the pulleys. The chart in Figure 34 shows the various combinations of belt positions for achieving a range of six speeds. Always disconnect the power to the machine before making adjustments, set-up changes or cleaning. Failure to do so could result in injury to yourself and others. THE SPINDLE SPEEDS A B C MOTOR ⁄ min 4. Move the V-belts to the A and F positions. 5.
Start Up and Spindle Break-in Procedures It is essential to closely follow the proper break-in procedures to ensure trouble free performance. Complete this process once you have familiarized yourself with all instructions in this manual. To begin the start up and break-in procedure: 1. Check oil levels in the headstock and apron. Follow all lubrication procedures highlighted in Lubrication in the MAINTENANCE section on Page 51 of this manual. 2.
Feed Selection NOTICE Never move the feed rate lever while machine is running. Damage to the machine will occur. NOTICE DO NOT force any lever on this machine. If the lever will not engage, with the machine OFF, rotate the chuck by hand while keeping light pressure on the selector. As the chuck rotates it aligns the gear teeth inside the selector box and as the gears come to engage the selector will engage. Figure 37. Feed rate selection lever.
Reading the Charts THE SPINDLE SPEEDS ⁄ min A B for C D Charts the powerfeed and thread cutting feaE F tures for the lathe are located on the bottom of the MIDDLE lower MOTOR belt guard. Figure 38 shows SPINDLE a segment of A-D B-E C-D theA-F chart A-E for feed ratesB-F with aC-F brief description. 160 300 375 470 600 870 1380 30 36 42 A 24 1 A 0.25 0.30 0.35 I 0.2 MM 0.125 0.15 0.175 II 0.1 III 0.05 0.063 0.075 0.088 B C I 0.008 0.010 0.012 0.014 2 INCH II 0.004 0.005 0.006 0.007 D III 0.002 0.0025 0.
Half Nut Apron Power Feed The half nut lever is located under the left hand side apron (Figure 40). This handle may be engaged and disengaged while the machine is running and while making a cut. Move the lever to the down position to engage the half nut. Because the threads of the nut and leadscrew will not always be aligned, engaging the half nut may require waiting until they align, with the machine running. Lift the handle in the direction of the arrow as shown in Figure 40.
Changing Gears A Changing gears on the Model G9729 is straight forward. Refer to the label found on the bottom of the lower belt guard for proper gear selection while following the example below. We will be changing the gears to those that would be used to set the machine for a 0.002" per revolution feed rate. These instructions assume that all of the gears need to be changed. The number of teeth are stamped on each gear.
7. Insert the bushing into the 60/100 tooth combination gear from the side that has 60 teeth. Align the flats of the bushing to the slot in the gear support arm and loosely fasten the assembly to the T-nut using the cap screw. Slide the combination gear along the slot in the support arm until gear C engages with gear D, and tighten the cap screw (see Figure 44). 8. Inch Threading The inch threading gear chart is illustrated in Figure 46.
The Model G9729 is capable of cutting many standard inch and metric threads. Follow the procedures listed in Changing Gears in the previous section and change the gears according to the chart for the thread desired. B&C Example: The example shown in Figures 47–50 depicts the order the gears should be installed for a 120/127, 72, and 30 tooth gear set-up. Note—This example shows gearing for cutting a 5, 10, or 20 thread per inch (TPI) screw thread.
Cutting Threads 1. 2. 3. 4. 5. TPI Set the compound rest to the appropriate angle for the given thread you want to cut. For a Unified National Series thread, this is 29º off of vertical to spindle axis. Set the tool tip perpendicular to the workpiece and center it vertically. Make sure the thread dial is engaged with the lead screw. If not, use a hex key wrench to loosen the screw and rotate the thread dial until the gear engages with the lead screw, then tighten the screw to hold the dial in place.
Metric Threading The metric threading gear chart is illustrated in Figure 52. The layout is listed below to help identify gears for cutting threads with metric pitches. The chart below lists threads in millimeters. 3 1 A mm 120T 127T 24T mm A 36 42 48 60 72 III II I 4 Example: To cut a thread with a pitch of 1.
SECTION 5: MILL OPERATIONS Mill Speeds The speed of the drill press spindle is controlled by two belts mounted between three pulleys. The belts and pulleys are accessed by removing the upper belt guard (Figure 54). To select a spindle speed of 310 RPM, start by moving the right hand belt to the “D” position. Move the left hand belt to the “A” position. Always disconnect the power to the machine before making adjustments, set-up changes or cleaning.
Head Rotation Fine Down Feed The head of the Model G9729 can be rotated 90° in both directions. The up and down motion of the mill spindle is controlled just like a drill press. But unlike most drill presses, the Model G9729 is supplied with a fine feed handle, indicated by the arrow in Figure 58. To rotate the head: 1. Unplug the lathe/mill! 2. Loosen the head lock handles shown in Figure 56. 3. Rotate the head to the desired position. 4. Tighten the head lock handles.
Machine Vise The Model G9729 comes supplied with a milling vise that also serves as the compound for the lathe. The 4-way tool post must be removed before using the vise. The milling vise can be aligned to the axis of the lathe or at any angle desired. Care must be given to setting the vise if a precision angle is needed. The following instructions are given to make the jaws parallel to the travel of the cross slide. 5.
Drill Chuck Removal Drill Chuck Mounting The drill chuck and arbor come installed on the drill press/milling spindle from the factory. When the time comes to remove and reinstall it, use these instructions: 1. Unplug the lathe/mill! 2. Remove the small plastic cap on top of the belt guard and slide the draw bar out of the spindle through the top. 3. Clean the spindle taper and the arbor taper thoroughly, then wipe with your hand until its clean. 4.
SECTION 6: ACCESSORIES G5641—1-2-3 Blocks G9815—Parallel Set Blocks are square to within .0003". Measure 1" x 2" x 3". Parallel set measures 6" long by 1/2", 5/8", 3 /4", 7/8", 1", 11/8", 11/4", 11/8", 13/8", 11/2", and 15/8". G9256—6" Dial Caliper G9257—8" Dial Caliper G9258—12" Dial Caliper These traditional dial calipers are accurate to 0.001" and can measure outside surfaces, inside surfaces, and heights/depths. Features stainless steel, shock resistant construction and a dust proof display.
G9864—3" 4-Jaw, Plain Back Chuck G9865—6" 4-Jaw, Plain Back Chuck Each jaw is adjusted independently. These chucks are used for holding odd shaped pieces or where zero tolerance is required. These chucks have semi-steel bodies and hardened reversible jaws. Requires a mounting plate. Figure 64. Four-Jaw, Plain Back Independent Chuck.
SECTION 7: MAINTENANCE Cleaning Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily Check: • Loose mounting bolts. • Damaged tool bits and end mills. • Worn or damaged wires. • Any other unsafe condition. • Lubrication. Monthly Check: • V-belt tension, damage, or wear.
Lubrication Your Model G9729 will function best when it is clean and well lubricated. Take the time to wipe down and oil the machine before each use. We recommend using ISO 68 or SAE 20W nondetergent oil unless otherwise specified. Ball fittings will require the use of an oil gun. Press the ball with the tip of the gun and squirt a little oil under pressure. Wipe the ball fitting before and after each use to prevent contamination.
Motor: The bearings used in the motor are shielded and lubricated for life, therefore, no lubrication is necessary. Leadscrew: Be sure to clean and lubricate the leadscrew. There is also a bearing on the tail stock end that will require oil. Headstock Gearbox: The oil in the headstock should be changed after the first 2 hours of use, then every 6 months, depending on usage. We recommend using a light weight, non-detergent oil.
SECTION 8: SERVICE Gibs Always disconnect power to the machine before performing service adjustments. Failure to do this may result in serious personal injury. About Service There are three gib adjustments for the Model G9729— the cross-slide gib, the compound slide gib and the apron gib. Cross-slide Gib: The gib on the cross-slide is adjusted by tightening or loosening the 2 wing bolts located on the right hand side of the slide (see Figure 74). These will also serve as table locks.
Compound Gib: The gib on the compound has two set screws to maintain tension on the slide (see Figure 75). To adjust these to the proper tension, loosen the cap screw positioned between them and turn the hand crank while adjusting each screw. Tighten until extra effort is required to move the slide then back off the set screw a little. When needed, the slide can be locked in place using the cap screw.
Troubleshooting Symptom Possible Cause Motor will not start. 1. Check power line for proper voltage. 1. Low voltage. 2. Open circuit in motor or loose connec- 2. Inspect all lead connections on motor for loose or open connections. tions. 3. Replace start capacitor. 3. Faulty start capacitor. Motor will not start; fuses or circuit break- 1. Short circuit in line cord or plug. ers blow. Possible Solution 1. Repair or replace cord or plug for damaged insulation and shorted wires.
Electrical Diagram L ~ N N L ~ AC Contactor -S3 Micro Switch 1 -S4 Power Indicator Light 3 -K HL 5 -S5 -S1 E E-Stop Switch 7 -S2 9 Power Switch Mill Switch Lathe Switch V1 U1 V1 U1 V2 U2 M1 PE V2 U2 M2 PE Mill Motor Lathe Motor Figure 77. G9729 wiring diagram.
Electrical Components Micro Switch Run Capacitor Start Capacitor Power Light Power Button E-Stop Button Lathe Reversing Switch AC Contactor G9729 Combination Lathe/Mill Wiring Block -57-
-58- 133 131 124 139 10 127 125 129 126 130 128 114 132 21 138 20 19 18 17 22 153 150 136 144 168 152 135 137 154 115 145 167 156 116 162 159 147 160 133 166 15 158 14 163 13 131 151 148 147 122 143 142 141 140 121 146 149 123 124 117 164 161 134 165 155 119 113 114 112 118 119 120 111T-6 9 101 111T 111T-2 23 111T-7 8B 8C 8D 7 8 8A 111T-5 111T-1 111T-4 111T-3 PARTS G9729 Lathe Bed G9729 Combination Lathe/Mill
G9729 Parts Breakdown 0-199 Series REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 6 7 8 8A 8B 8C 8D 9 10 13 14 15 17 18 19 20 21 22 23 101 102 103 104 105 107 108 109 110 110A 110B 111T 111T-1 111T-2 111T-3 111T-4 111T-5 111T-6 11T-7 112 113 114 115 116 117 118 119 P9729001 P9729002 P9729006 P9729007 PAW03M PAW04M PAW05M PAW06M PAW08M P9729009 P9729010 P9729013 P9729014 P9729015 P9729017 P9729018 P9729019 P9729020 P9729021 P9729022 P9729023 P9729101 P9729102 P9729103 P9729104 PSS21M P9729107 P9729
-60- 240 232 233 213 237 268 267 238 272 264 273 262 266 263 414 228 261 231 407 405 234 406 232 219 220 226 269 270 210 209 208 207 206 265 271 211 214 212 235 239 236 203 227 202 201 252 404 401 218 212 254 257 256 248 277 409 221 247 245 241 408 242 243 249 258 223 250 222 229 230 212 225 224 260A 253 244 402 403 205 406 255 247 246 276 412 757 001 275 G9729 Lower Head Assembly G9729 Combination Lathe/Mill
G9729 Parts Breakdown 200 Series REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 203 205 206 207 208 209 210 211 212 213 214 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 HEX BOLT M10-1.5 X 40 FLAT WASHER 10MM TAPER PIN 10 X 40 HEADSTOCK TRIPLEX GEAR BRASS BUSHING O RING O RING SEAT PHLP HD SCR M5-.8 X 12 KEY 5 X 5 X 25 E-CLIP 14MM SHAFT D KEY 4 X 4 X 10 ROLL PIN 4 X 20 SET SCREW M5-.8 X 20 HEX NUT M5-.8 PHLP HD SCR M5-.
-62- 325 333 332 331 330 334 313A 317-1 320 327 318A 337 326 329 328 D A A A-F 16 0 310 R A-E 30 0 E B-F 47 0 DL MID C D E F IN SP in ⁄m 24 72 II III I II III I ⁄ ⁄ ⁄ 16 8 4 24 54 27 ⁄ 18 9 4.5 27 60 30 ⁄ 20 10 5 30 5 66 33 ⁄ 22 11 ⁄ 33 72 36 18 24 12 6 36 4 78 39 ⁄ 26 13 ⁄ 39 84 42 ⁄ 28 14 7 42 5 2.5 1.5 96 48 24 32 16 8 48 0 12 60 30 40 20 10 60 6 3 -F DL A E 60 24 B-E 0 I 0. 30 870 C-D II 0.2 13 0.
G9729 Parts Breakdown 300 Series REF PART # DESCRIPTION REF PART # DESCRIPTION 301 302 303 304 306 307 308 309 310 311 312 313 313A 314A 315 316 317 317-1 318A P9729301 PS56M PS07M P9729304 P9729306 P9729307 P9729308 P9729309 PS18M P9729311 P9729312 P9729313 P9729313A P9729314A P9729315 PS38M P9729317 P9729317-1 P9729318A STRAIN RELIEF 1/2" SNAP IN PHLP HD SCR M4-.7 X 16 PHLP HD SCR M4-.7 X 8 ELECTRIC BOX ELECTRIC HOUSING PULLEY BOX MICRO SWITCH STRAIN RELIEF 1/2" SNAP IN PHLP HD SCR M4-.
G9729 Headstock Assembly 529 501 521 560 559 518 517 519 557 556 555 516 515 579 527 558 553 514 530 A B C D E 548 552 520 547 545 528 544 546 526 578 525 551 619 524 523 554 522 550 543 628 627 618 571 505 570 506 509 503 510 507 605 607 508 603 625 602 626 608 612 505 620 606 616 574 609 623 624 621 622 502 604 615 610 541 601 611 536 573 572 617 511A 537 563 512 570 535 564 562 565 568 610 569 614 567 110A 566 577 110B 613 -64- 504 561
G9729 Parts Breakdown 500 & 600 Series REF PART # DESCRIPTION REF PART # DESCRIPTION 501 502 503 504 505 506 507 508 509 510 511A 512 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 535 536 537 541 543 PVM33 PSB47M P9729503 P9729504 P9729505 P9729506 P9729507 P9729508 P9729509 P9729510 P9729511A P9729512 P9729514 P9729515 PSB02M PSS14M P9729518 PS17M P9729520 P9729521 P9729522 PSB29M P9729524 P6008 PR68M PVM35 P9729528 P9729529 P9729530 P9729535 P9729536 P9729537 P9729541 P9729543
-66- 710 782 783 779 778 711 713 701 712 719 703 726 737 735 732 722 705 784 733 770 727 718 736 702 715 771 734 723 773 772 776 705 774 704 721 729 725 707 705 701 724 706 728 731 720 730 701 G9729 Crossslide Assembly G9729 Combination Lathe/Mill
G9729 Parts Breakdown 700 Series REF PART # DESCRIPTION REF PART # DESCRIPTION 701 702 703 704 705 706 707 710 711 712 713 715 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 PSB15M P9729702 P9729703 P9729704 P9249002 P9729706 P9729707 PS19M P9729711 PW02M P9729713 P9729715 P9729718 P51102 P9729720 P9729721 PK102M P9729723 P9729724 P9729725 P9729726 P9729727 P9729728 PSS03M P9729730 P9729731 PSS06M PSS14M P9729734 P9729735 P9729736 P9729737 PSS2
G9729 Apron Assembly 763 723 738 739 760 744 741 729 761 744 748 742V2 763 740 780 758 749 743 745 746 766 765 747 723 767 781 764 769 778 779 750 768 783 715 784 753 785 713 752 753 759 711 770 754 782 750 751 710 712 T204 752 T203 T202 T207 T208 T201 T205 T206 -68- G9729 Combination Lathe/Mill
G9729 Parts Breakdown T Series REF PART # DESCRIPTION REF PART # DESCRIPTION T201 T202 T203 T204 T205 T206 T207 T208 T501 T501-1 T502 T503 T504 T505 T506 T507 T508 T509 T510 T511 T512 T513 T514 T515 T516 T517 T518 T519 T606 T606-1 T610 T611 T701 T702 T703 T704 T705 P9729T201 P9729T202 P9729T203 P9729T204 P9729T205 P9729T206 P9729T207 PCAP30M P9729T501 P9729T501-1 P9729T502 P9729T503 PW01M P9729T505 P9729T506 PW03M P9729T508 P9729T509 P9729T510 P9729T511 P9729333 PRP02M PSS64M PN01M PSB44M PW04M P9729
G9729 Rests Assemblies T512 T511 T512 T513 T510 T514 T511 T515 T509 T513 T519 T508 T502 T510 T514 T506 T503 T515 T509 T504 T519 T505 T507 T516 T606 T517 T501 T518 T610 T611 T606-1 -70- T501-1 G9729 Combination Lathe/Mill
G9729 Combination Lathe/Mill T703 T724 T708 T707 T742 T741 T706 T709 T704 T705 T703 T736 T717 T715 T730 T714 T719 T731 T732 T733 T735 T737 T725 T738 T718 T710 T727 T728 T704 T705 T734 T711 T740 T702 T729 T701 T722 T721 T723 T711 T710 T739 T720 T716 6 T713 T712 G9729 Compound Assembly -71-
G9729 Tailstock Assembly 924 925 923 909 921 907 918 922 906 934 920 937 908 935 933 919 926 927 917 914 901 902 903 916 905 915 913 931 912 904 938 930 928 927 929 2 107 109 936 935 105 102 110 108 103 104 -72- G9729 Combination Lathe/Mill
G9729 Parts Breakdown 900 Series REF PART # DESCRIPTION REF PART # DESCRIPTION 901 902 903 904 905 906 907 908 909 912 913 914 915 916 917 918 919 920 P9729901 P9729902 P9729903 P9729904 PSS52M P9729906 PK05M P9729908 PRP35M P9729912 P9729913 P9729914 P9729915 PW04M P9729917 P9729918 P9729919 P9729920 TAILSTOCK T-KEY TAILSTOCK NUT TAILSTOCK BARREL SET SCREW M4-.7 X 8 TAILSTOCK SCREW KEY 4 X 4 X 10 SPACER ROLL PIN 5 X 10 DIAL DIAL SEAT SPRING PIECE HANDWHEEL 12 X 100 FLAT WASHER 10MM ACORN NUT M10-1.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name______________________________________________________________________________ Street______________________________________________________________________________ City_ _______________________ State__________________________ Zip_ _____________________ Phone #_____________________ Email_ ________________________ Invoice #__________________ Model #_____________________ Order #________________________ Serial #___________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value! Visit Our Website Today And Discover Why Grizzly® Is The Industry Leader! • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR -OR- Call Today For A FREE Full Color Catalog
