MODEL G9744Z2 10" X 18" METAL CUTTING BANDSAW MANUAL INSERT For Machines Mfd. Since 10/13 and Owner's Manual Printed 07/06 The Model G9744Z2 is the same machine as the Model G9744Z but with minor updates to the headstock, belt tension mechanism and vise, and relocation of some electrical components. Additionally, the G9744Z2 uses a 1211⁄ 2" blade. The data sheet, electrical photos, and parts breakdowns in this insert replace the corresponding sections in the G9744Z manual.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G9744Z2 10" X 18" 1.5 HP METAL‐CUTTING BANDSAW Product Dimensions: Weight.............................................................................................................................................................. 705 lbs. Width (side-to-side) x Depth (front-to-back) x Height........................................................ 67-3/4 x 24-1/2 x 41-1/2 in.
Cutting Capacities Angle Cuts.................................................................................................................................... 45 — 90 deg. Vise Jaw Depth.......................................................................................................................................... 12 in. Vise Jaw Height........................................................................................................................................... 5 in. Max.
Replaces Manual Page 23 Blade Selection The Model G9744Z2 uses 1211⁄ 2" x 1" bandsaw blades. Selecting the right blade for the job depends on a variety of factors, such as the type of material being cut, hardness of the material, material shape, machine capability, and operator technique. The chart below is a basic starting point for choosing blade type based on teeth per inch (TPI) for variable-tooth-pitch blades and for standard raker type bi-metal blades/HSS blades.
Replaces Manual Page 38 Electrical Components SB4 Figure 47. Limit switch (SQ1). SB1 SB3 L Figure 49. Control panel wiring. Figure 48. Junction box (M1). (KM1) Relay Fuse (FU 2A) (KM1) Contactor (TC) Transformer Figure 50. Pump motor wiring and capacitor (M2). (KM2) Contactor Figure 51. Contactor & relay electrical box. Figure 52. Circuit breaker wiring. Model G9744Z2 (Mfd.
Parts Breakdown 375 374 376 377 373 372 354-8 354-6 354-12 354-11 354-1 354-2 341 340 354-9 620 338 354-4 333 332 330-1 330 329 E 354-10 354-5 328 371 370 369 G F 365 364 368 367 366 360-1 K 363 362 345-4 345-3 349 348 343 342 331 345 327 313 314 311 310 H 305 220-2 309 302-1 308 304 303 219 212 218 BA 133 134 B A 214 C 210 307 216 215 C TA RPM 1725 1-PH, 15.
Parts Breakdown 14 15 13 12 54 64 63 53 50 47 46 8 45 55 117 42 75 73 74-1 74 41 40 58 61 39 57 37 62 29 38 17-3 613 609 608 603 604 16-9 16-8 16-7 616 612 17-1 6-6 6-5 16-3 16 615 16-6 16-5 16-4 16-2 617 6V2 128 129 6-4V2 6-3 24-1 614 611 606 605 31 30 26 26-1 24 36 610 71 71-1 72 51 59 56 34 33 32 E 48 7 60 52 49 44 43 9 35 130 6-7 122 123 6-2 6-1 5 5-1 124 125 5-2 126 5-3 5-5 5-4 121 132 Z2 4 74 G9 Model G9744Z2 (Mfd.
Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 5 6V2 6-1 6-2 6-3 6-4V2 6-5 6-6 6-7 7 8 9 12 13 14 15 16 16-2 16-3 16-4 16-5 16-6 16-7 16-8 16-9 17-1 17-3 24 24-1 26 26-1 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CONTROL BOX ASSEMBLY PUMP SET 1/8HP 110/220V V2.07.12 CUTTING FLUID TANK HOSE13X19-350MM COUPLER PT1/2X1/4 PUMP 1/8HP 110/220V V2.07.
Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 220 220-1 220-2 220-3 220-4 220-5 220-6 220-7 221 222 222-1 222-2 222-3 222-4 222-5 222-6 223-1 224 225 226 300 301 302 302-1 302-2 303 304 305 306 306-1 307 308 309 309-1 310 311 312 313 314 314-1 314-2 314-3 314-4 314-5 314-6 315 315-1 316 316-1 317 318 VALVE ASSEMBLY CUTTING FLUID VALVE HOSE 6MM HOSE FITTING HOSE CLIP LOCK WASHER 6MM BUTTON HD CAP SCR M6-1 X 12 HOSE CLAMP 12MM LOWER BLADE GUIDE BLOCK BRUSH ASSEMBLY BRUSH SUPPORT BRACKET BLADE
Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 354-7 354-8 354-9 354-10 354-11 354-12 355 355-1 356 357 358 359 360 360-1 361 362 363 364 365 366 367 368 369 370 371 P9744Z2354-7 P9744Z2354-8 P9744Z2354-9 P9744Z2354-10 P9744Z2354-11 P9744Z2354-12 P9744Z2355 P9744Z2355-1 P9744Z2356 P9744Z2357 P9744Z2358 P9744Z2359 P9744Z2360 P9744Z2360-1 P9744Z2361 P9744Z2362 P9744Z2363 P9744Z2364 P9744Z2365 P9744Z2366 P9744Z2367 P9744Z2368 P9744Z2369 P9744Z2370 P9744Z2371 STRAIGHT CONNECTOR 1/4 NPT CAP SCRE
MODEL G9744Z 10"x18" Metal Cutting Bandsaw OWNER'S MANUAL COPYRIGHT © JULY, 2006 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................................................................................................ 3 Foreword..................................................................................................................................... 3 Contact Info................................................................................................................................. 3 Machine Data Sheet.............................................
SECTION 6: MAINTENANCE......................................................................................................... 30 Schedule................................................................................................................................... 30 Cleaning.................................................................................................................................... 30 Lubrication...................................................................................
INTRODUCTION Foreword Contact Info We are proud to offer the Model G9744Z Metal Cutting Bandsaw. This machine is part of a growing Grizzly family of fine metalworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. We stand behind our machines! If you have questions or need help, contact us with the information below.
Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G9744Z 10" X 18" METAL CUTTING BANDSAW Product Dimensions: Weight . ............................................................................................................................................................770 lbs. Length/Width/Height .....................................................................................................................
Cutting Capacities Angle Cuts............................................................................................................................................. 45°–90° Vise Jaw Depth.................................................................................................................................... 12-1/2 in. Vise Jaw Height........................................................................................................................................... 5 in.
Identification K A H I G B M J L F C D M E N Figure 1. G9744Z machine identification. A. B. C. D. E. F. G. H. I. J. K. L. M. N.
Control Panel A F B C D E Figure 2. G9744Z control panel. A. Coolant Pump Switch: Turns the coolant pump ON. B. EMERGENCY STOP/OFF Button: Interrupts power to the system and turns the motor OFF. Twist the button until it pops out to reenergize the system. Also works as a standard OFF button. Note: The bandsaw has an automatic shutoff (limit switch) that turns the motor and coolant pump OFF at the bottom of the cut. C. START Button: Turns the motor ON. D.
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. 10. NEVER LEAVE WHEN MACHINE IS RUNNING.
Additional Safety Instructions for Metal Cutting Bandsaws 1. BLADE CONDITION. Do not operate with dull, cracked or badly worn blade. Inspect blades for cracks and missing teeth before each use. 8. FIRE HAZARD. Use EXTREME CAUTION if cutting magnesium. Using the wrong cutting fluid will lead to chip fire and possible explosion. 2. HAND PLACEMENT. Never position fingers or thumbs in line with the cut. Hands could be crushed in vise or by falling machine components or cut by the blade. 9. 3.
SECTION 2: CIRCUIT REQUIREMENTS 220V Single-Phase Serious personal injury could occur if you connect the machine to the power source before you have completed the setup process. DO NOT connect the machine to the power source until instructed to do so. Grounding In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connected to the grounding prong on the plug; likewise, the outlet must be properly installed and grounded.
SECTION 3: SETUP Setup Safety This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! The Model G9744Z is an extremely heavy machine. Serious personal injury may occur if safe moving methods are not followed.
Inventory After all the parts have been removed from the crate, you should have the following items: Box 1: (Figure 4) Qty A. Model G9744Z Bandsaw............................. 1 Hardware and Tools (Not Shown) • Chip Tray..................................................... 1 • Triangle Screw 5/16-18 x 3/4"..................... 1 • Flat Washer 5/16"........................................ 1 • Hex Nut 5/16-18.......................................... 1 • Hex Bolts M12-1.75 x 50 (Leveling)............
Hardware Recognition Chart 5mm -14- G9744Z Metal Cutting Bandsaw
Clean Up The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For optimum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated.
Moving & Placing Base Unit The Model G9744Z is an extremely heavy machine. Serious personal injury may occur if safe moving methods are not followed. To be safe, you will need assistance and power equipment when moving the shipping crate and removing the machine from the crate. The Model G9744Z comes with lifting brackets installed on the base. Use a forklift and straps rated for the machine weight to lift the machine off the pallet and onto a suitable location (see Figure 6).
Shipping Bracket Workstop A bracket has been installed to keep the saw in alignment during shipping. Before using your saw you will need to remove it. Store it for safe keeping in the event you move your saw to a different location. The workstop is used when many cuts of the same length are needed (see Figure 9). To setup the workstop: 1. Position the workstop rod the desired distance from the blade and tighten the cap screw to hold it in place. 2.
Chip Tray Feed Stop Components and Hardware Needed: Qty Chip Tray............................................................ 1 Depending on how the Model G9744Z was shipped, it may be necessary to adjust the feed stop before the test run. The blade should not make contact with any part of the vise assembly. The chip tray fits over the lip of the base as illustrated in Figure 10. To adjust the feed stop bolt: 1.
Recommended Adjustments E-STOP/OFF Button ON Feed control knob The adjustments listed below have been performed at the factory. However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure accurate cutting results. Step-by-step instructions on verifying these adjustments can be found in SECTION 7: SERVICE ADJUSTMENTS. Factory adjustments that should be verified: 1. Blade Tracking (Pages 35 & 36). 2.
SECTION 4: OPERATIONS Operation Safety Vise Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Always turn the saw OFF and allow the blade to come to a complete stop before using the vise! Failure to follow this caution may lead to injury.
The vise can be adjusted to cut any angle from a straight 90 degree cut-off, to a 45 degree angle by loosening the two vise lock handles. Positive stops at 90° and 45° allow you to quickly return the rear jaw to either angle. Angles between 90° and 45° can be read using the scale on the side of the vise table. Use a combination square or bevel protractor if higher precision is required when finding these angles. To adjust the positive stops: 1.
Blade Guide Arms The blade guide bearings are mounted on the front and rear arms. The rear arm is adjustable and should be set as close to the workpiece as possible. This will help ensure straight cuts by keeping the blade from twisting and drifting off of the cut line. The front blade guide arm has a self-adjusting wire brush that makes contact with the blade to help clear away chips and extend blade life (see Figure 18).
Blade Selection 2. Refer to the "Material Width/Diameter" row of the blade selection chart in Figure 19 and read across to find your workpiece thickness you need to cut. 3. Selecting the right blade for the job depends on a variety of factors, such as the type of material being cut, hardness of the material, material shape machine capability, and operator technique. Refer to the "Material Shapes" row and find the shape and material to be cut. 4.
Blade Speed 114 196 288 377 Entanglement Hazard! You MUST install the pulley cover before operating or severe injury may occur. The Model G9744Z has four speed settings—114, 196, 288, and 377 feet per minute (FPM). Refer to the chart on Page 23 for cutting speed recommendations by material type. Drive Wheel Figure 21. V-belt positions in FPM. 5. Lift the motor to tension the belt and tighten the belt tension knob. 6. Close the belt cover. Feed Rate To change blade speeds: 1.
Coolant System FIRE HAZARD! DO NOT cut magnesium when using oil-water solutions as a cutting fluid! Always use a cutting fluid intended for magnesium. The water in the solution will cause a magnesium-chip fire. 2. Thoroughly clean and remove any foreign material that may have fallen inside the reservoir during shipping. 3. Fill the reservoir with your chosen cutting fluid solution and replace the rear panel. 4. Make sure the coolant control valve is turned OFF. 5.
Cutting Fluid BIOLOGICAL and POISON HAZARD! BIOLOGICAL AND POISON HAZARD! Use proper personal protection equipment when handling cutting fluid and follow federal, state, and fluid manufacturer requirements to properly dispose of cutting fluid. While simple in concept and function, many issues must be taken into account to find and use the correct cutting fluid. Always follow all product warnings and contact the fluid manufacturer for unanswered questions.
Operation Tips You need to change coolant when you notice the following conditions: • Low sump level • Abnormal appearance (change in fluid color) • Foul smell (rancidity) • Floating matter on the fluid (chips, swarf, mold) • Tramp oil floating on the surface (leaking machine and hydraulic oils) • Excessive foam (improper mixture, too high of pressure, excessive air in system) • Dirty machine or trenches (cleaners in the fluid have become depleted) • User notices skin irritation • User has
SECTION 5: ACCESSORIES Tool Steel Blades G6432—1293⁄8 x 1 x .032 10 TPI Raker G6433—1293⁄8 x 1 x .032 14 TPI Raker Variable Pitch Bi-Metal Blades G6434—1293⁄8 x 1 x .032 3-4 Variable Pitch G6435—1293⁄8 x 1 x .032 4-6 Variable Pitch G6436—1293⁄8 x 1 x .032 5-8 Variable Pitch G6437—1293⁄8 x 1 x .032 6-10 Variable Pitch G6438—1293⁄8 x 1 x .032 8-12 Variable Pitch H5405—Lenox® Lube Tube™ Lenox® Lube Tube™ is a stick lubricant designed to prevent heat buildup.
G5618—Deburring Tool with Two Blades G5619—Extra Aluminum Blades G5620—Extra Brass and Cast Iron Blade The quickest tool for smoothing freshly machined metal edges. Comes with two blades—one for steel/aluminum and one for brass/cast iron. H4978—Deluxe Personal Hearing Protector H4979—Deluxe Twin Cup Hearing Protector T20446—Ear Plugs, 200 Pair Protect yourself comfortably with a pair of cushioned earmuffs. Especially important if you or employees operate for hours at a time. H1302 T20446 H4979 Figure 29.
SECTION 6: MAINTENANCE Lubrication Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Since all bearings are sealed and permanently lubricated, leave them alone until they need to be replaced. Do not lubricate them.
• • • Blade and Guides: Drop a few drops of light machine oil on the blade and the blade guides daily, especially when cutting cast iron, as no cutting fluid is recommended (see Figure 33). The gearbox should be drained and refilled after the first 50 hours of use and then once every year. Use a high quality, ISO 68 or SAE 90 gear oil. Table and Machined Surfaces: Tables can be kept rust-free with regular applications of products like SLIPIT®.
SECTION 7: SERVICE Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. Troubleshooting Motor & Electrical SYMPTOM POSSIBLE CAUSE Machine does not start or a 1. Emergency-Stop button pressed. breaker trips. 2. Plug/receptacle is at fault or wired incorrectly. 3. Start capacitor is at fault. 4.
Bandsaw Operations SYMPTOM POSSIBLE CAUSE Machine is loud when cutting or bogs down in the cut. 1. Excessive feed rate. Blades break often. 1. Blade is not tensioned correctly. 2. The blade TPI is too great, or the material is too coarse. 2. 3. 4. 5. 6. 7. 8. Blade dulls prematurely. 1. The cutting speed is too fast. 3. The blade feed pressure is too light. 4. The workpiece has hard spots, welds, or scale is on the material. 5. The blade is twisted. 6. The blade is slipping on the wheels.
Blade Change CUTTING HAZARD! Blades are sharp! Wear heavy leather gloves when handling blades to prevent cuts. Upper Blade Guard & Screw Holes Blades should be changed when they become dull, damaged, or when you are using materials that require a blade of a certain type or tooth count. To change the blade on the bandsaw: 1. UNPLUG THE BANDSAW! 2. Raise the bow of the bandsaw about six inches, lock in position by turning the feed control knob to the right to close the feed control valve. 3.
Note: It is sometimes possible to flip the blade inside out, in which case the blade will be installed in the wrong direction. Check to make sure the blade teeth are facing toward the workpiece, as shown in Figure 40, after mounting on the bandsaw. Some blades will have a directional arrow as a guide. Bl ad To tension the blade on the bandsaw: 1. Turn the blade tension handle clockwise to tension the blade. 2.
The blade tracking has been properly set at the factory. The tracking will rarely need to be adjusted if the bandsaw is used properly. To adjust the blade tracking on the bandsaw: 1. Loosen or tighten the tracking set screw in Figure 42 until the blade is tracking properly. The blade is tracking properly when the back of the blade is lightly touching the flange of both wheels. To adjust the blade guide bearings: 1. Before making adjustments, make sure the blade is tensioned and tracking correctly. 2.
Set Screw Guide Bearings Eccentric Bushing Carbide Blade Guide Figure 45. Square blade to table. Figure 44. More blade guide adjustments. 2. Turn the square nut on the eccentric shaft to adjust the distance of the guide bearing. The guide bearings and blade should make light contact or have a maximum clearance of 0.002". 3. Adjust the carbide blade guides so they make the same contact with the blade as the bearings. 4. Adjust the eccentric blade guide roller bearing on the front arm the same way.
Electrical Components SB4 SB1 SB3 L Figure 47. Limit switch (SQ1). Figure 49. Control panel wiring. Figure 48. Junction box (M1). Figure 50. Pump motor wiring and capacitor (M2). (TC) Transformer (KM1) Contactor (KM1) Relay (KM2) Relay Fuse (FU 2A) Figure 51. G9744Z Contactor & relay electrical box.
Model G9744Z 220V Wiring Diagram 1~ 220V 60Hz L1 L2 PE N L TC 24V 8 G Relay KM1 KM2 7 FU 2A 1 SB1 L U1 V1 6 SQ1 2 U2 V2 KM1 SB3 M1 M2 Main Motor Pump Motor 3 SB4 4 KM2 KM1 PE 7 7 LEGEND M = Motor KM1 = Contactor Main Motor KM2 = Pump Motor Relay KM1 = Thermal Relay Main Motor L = Indicator Lamp SB1 = Emergency Stop Button SB3 = Start Button SB4 = Pump Motor Switch SQ1 = Limit Switch TC = Transformer for Control System (24V) FU2A = Fuse G9744Z Metal Cutting Bandsaw -39-
-40- 9 10 6 8 7 5 1-1 4 1-2 1-3 3 2 46 1 45 42 50 44 1-10 51 77 1-13 1-14 50 49 43 1-9 48 47 1-7 1-8 41 1-12 1-11 1-6 1-4 1-5 52 71 60 52-2 76 75 74 52-1 61 59 56 58 70 69 73 1-16 1-15 72 92 54 55 59 78 67 79 57 53 58 80 88 63 64 68 90 89 91 82 87 81 78 80 79 93 95 107 104 103 105 104 86 85 106 105 109 83 108 106 84 100 94 Blade Guide Parts Breakdown G9744Z Metal Cutting Bandsaw
G9744Z Metal Cutting Bandsaw 216 222 218 217 216 219 219 137A-2 220 216 216 137A-4 221 116 106 108 180 107 106 179 48 178 47 181 177 118 122 187 147 148 152153 121 120 119 188 192 193 191 192 194 189 195 117 172 173 175 176 170 171 185 196 105 195 194-1 194 173 174 105 137A-5 137A-1 137A-3 140 126 124 149 155 154 163 162 61 60 157 156 160 58 59 158 59 129 127 120 136 131 130 128 127 125 141 135 161 146 142 143 144 145 123 134 132 133 137A 13
-42- 358 357 372 370 356 373 239 374 375 362 360 361 363 359 238 232 233 371 236 237 235 234 230 231 376 280 281 310 312 313 380 382 378 377 379 383 381 342 341 343 315 279 316 311 283 282 301 312-1 302 317 300 302 303 301 284 308 305 329-2 329 305 300 285 289 304 306 318 286 299 288 329-1 287 307 307298 290 296 329-3 329-4 284 297 291 319 321 269 270 320 295 265 326 271 272 338 268 273 262 264 339 323 263 266 259 267 258 340 274 260 322 349 261 294 323 275 328 240 331 244
REF PART # DESCRIPTION 1 P9744Z001 1-1 P9744Z001-1 1-2 Parts List REF PART # DESCRIPTION SLIDE SET 67 PLW02 LOCK WASHER 1/4 SLIDE 68 PSB04M CAP SCREW M6-1 X 10 P9744Z001-2 SPECIAL SET SCREW 69 P9744Z069 SCALE 1-3 PN10 HEX NUT 7/16-20 70 P1005619 RIVET 2 1-4 PW04M FLAT WASHER 10MM 71 PSB77M CAP SCREW M12-1.75 X 30 1-5 PSB134M CAP SCREW M10-1.5 X 65 72 PSS09M SET SCREW M8-1.
Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 130 PB15M HEX BOLT M8-1.25 X 40 181 P9744Z181 BRUSH ASSY 131 PW07 FLAT WASHER 5/16 185 P9744Z185 MOTOR PULLEY COVER 132 P9744Z132 MOTOR PLATE 187 P9744Z187 SPINDLE PULLEY 133 PW07 FLAT WASHER 5/16 188 P9744Z188 MOUNT PULLEY 134 PN03M HEX NUT M8-1.25 189 PS39M PHLP HD SCR M8-1.25 X 10 135 PSS01M SET SCREW M6-1 X 10 191 PK20M KEY 5 X 5 X 15 136 P9744Z136 PIVOT SHAFT 192 PSS16M SET SCREW M8-1.
Parts List REF PART # DESCRIPTION REF PART # 270 P9744Z270 DISTANCE SET BRACKET 326 PS70M PHLP HD SCR M5-1 X 8 271 P9744Z271 SUPPORT ROD 328 P9744Z328 NAME PLATE 272 PLW02 LOCK WASHER 1/4 329 P9744Z329 COMPLETE ELECTRICAL BOX 273 P9744Z273 THUMB SCREW 329-1 P9744Z329-1 COMPLETE FUSE HOLDER 274 PSS01M SET SCREW M6-1 X 10 329-2 P9744Z329-2 CONTACTOR LCK09 275 PR11M EXT RETAINING RING 25MM 329-3 P9744Z329-3 THERMAL OVERLOAD LR7K0332 278 PB14M HEX BOLT M10-1.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
