MODEL H6330 21⁄4 GALLON PAINT TANK INSTRUCTION MANUAL Copyright © MAY, 2008 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape or form without the written approval of Grizzly Industrial, inc.
4HIS MANUAL PROVIDES CRITICAL SAFETY INSTRUCTIONS ON THE PROPER SETUP OPERATION MAINTENANCE AND SERVICE OF THIS MACHINE EQUIPMENT &AILURE TO READ UNDERSTAND AND FOLLOW THE INSTRUCTIONS GIVEN IN THIS MANUAL MAY RESULT IN SERIOUS PERSONAL INJURY INCLUDING AMPUTATION ELECTROCUTION OR DEATH 4HE OWNER OF THIS MACHINE EQUIPMENT IS SOLELY RESPONSIBLE FOR ITS SAFE USE 4HIS RESPONSIBILITY INCLUDES BUT IS NOT LIMITED TO PROPER INSTALLATION IN A SAFE ENVIRONMENT PERSONNEL TRAINING AND USAGE AUTHORIZATION PROPER INS
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
7. AVOID ENTANGLEMENTS. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry, which may get caught in moving parts, when operating this tool. Wear a protective hair covering to contain long hair. 8. USE CORRECT AIR PRESSURE. Exceeding the maximum PSI rating of this tool may cause unpredictable operation or bursting. 9. DISCONNECT AIR PRESSURE before servicing, changing accessories, or moving to another location. Never leave this tool unattended when connected to air. 10.
Additional Safety Instructions for Paint Tanks 1. Read this manual. This manual contains proper operating instructions for this paint tank. 2. DESIGN MODIFICATIONS. Do not modify the tank design or construction. Drilling into the tank or weld attachments, or altering its design, could weaken the tank. 3. CLEANING AND MAINTENANCE. Clean and dry the tank and lid according to the instructions in this manual.
INTRODUCTION Foreword The specifications, details, and photographs in this manual represent the Model H6330 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Specifications Paint Tank Material Capacity............21/4 Gallons (8.5 L) Operating Pressure.....................25–30 PSI Maximum Operating Pressure..........50 PSI Tank Construction............
SETUP Unpacking Inventory Your paint tank was carefully packaged for safe shipping. If you discover any damage after you have signed for delivery, immediately call Customer Service at (570) 5469663 for advice. H6330 Inventory (Figure 1)................ Qty A. Paint Tank 21⁄4 Gallon........................... 1 B. Lid......................................................... 1 C. Regulator Assembly............................. 1 D. Lift Handle............................................
Tank Assembly Pressure Gauge Lift Handle Regulator Assembly Air Inlet Fitting Air Outlet Fitting Fluid Outlet Adapter Safety Valve Figure 2. Regulator and lift handle installed on paint tank. To assemble the paint tank: 6. Connect a 1/4" NPT material hose (not included) to the fluid outlet adapter on the tank lid. 1. Apply pipe thread tape to all male pipe threads. 7.
OPERATIONS Tank Regulator The pressure regulator on the paint tank controls the amount of pressure in the paint tank and the spray gun. The following are operating guidelines for internal and external spray guns: Internal Mix Guns: Use higher tank pressures up to the full amount of air pressure being delivered to the spray gun. However, do not exceed 50 PSI at the spray gun or in the paint tank. External Mix Guns: Use lower tank pressures—approximately 12 PSI for most external mix guns.
3. Place the lid assembly on the tank and evenly hand tighten the lid clamp wing screws. 4. Adjust the regulator at your air compressor to 50 PSI. 5. Fully turn the regulator T-handle counterclockwise to shut the tank regulator OFF. Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed.
CLEANING AND LUBRICATION Cleaning the Tank Proper cleaning is the best way to ensure trouble free performance from your paint tank. If your tank is not thoroughly cleaned, damage and poor operation will result. Problems caused by improper cleaning will not be covered by the warranty. Clean the tank immediately after each use. To clean your paint tank: 1. DISCONNECT THE AIR SUPPLY FROM THE TANK! 3. Turn the tank regulator T-handle counterclockwise until you no longer feel spring tension. 4.
Tank Troubleshooting Symptom Possible Cause Solution Air escaping from regulator port. 1. Broken or damaged diaphragm in tank regulator. 1. Replace tank regulator. Pressure dropping slowly on regulator. 1. Dirty or worn valve seat in regulator. 2. Loose air fittings leaking air. 1. Replace tank regulator. 1. Defective lid gasket. 2. Wing screw loose. 1. Replace lid gasket. 2. Tighten wing screws evenly. 3. Clean rim and gasket. Fluid or air leak at lid gasket. 3.
H6330 PAINT TANK TO REDUCE RISK OF SERIOUS INJURY WHEN USING THIS EQUIPMENT: H6330 21⁄4 GAL. PAINT TANK &. Capacity: 2 ⁄ Gallons Gun Type: Pressure Feed (HVLP or Conventional) Maximum Pressure: 50 PSI Operating Pressure: 25–30 PSI Tank Construction: Galvanized Steel Weight: 21 lbs. * 1. Do not exceed 50 PSI. 2. Do not use attachments with lower pressure ratings than the adjusted tank pressure. 3. Do not modify tank or substitute inferior components. 4. Do not tamper with safety valve. 5.
WARRANTY Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name__________________________________________________________________ Street__________________________________________________________________ City_ _______________________ State__________________________ Zip_ _________ Phone #_____________________ Email_ ________________________ Invoice #______ Model #_____________________ Order #________________________ Serial #_______ The following information is given on a voluntary basis.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here grizzly INDUSTRIAL, inc. p.o.
