Biscuit Joiner User Manual

BdYZa<%).%$<%).%MB[\#H^cXZ($%.
"(."
Cutterhead Inserts
(G0490X)
Figure 59.>chZgigdiVi^c\hZfjZcXZ#
I]ZBdYZa<%).%Mhe^gVaXjiiZg]ZVY^hZfj^eeZY
l^i]^cYZmVWaZXVgW^YZ^chZgihi]ViXVcWZgdiViZY
id gZkZVa Vcn dcZ d[ i]Z^g [djg Xjii^c\ ZY\Zh# >[
dcZZY\Zd[i]Z^chZgiWZXdbZhYjaadgYVbV\ZY!
h^beangdiViZ^i.%idgZkZVaV[gZh]Xjii^c\ZY\Z!
Vhh]dlc^cFigure 59#
5. GZeaVXZ i]Z ^chZgi hd i]Vi V [gZh] Xjii^c\
ZY\Z[VXZhdjilVgY#
·>[ Vaa [djg ^chZgi Xjii^c\ ZY\Zh ]VkZ WZZc
jhZY! gZeaVXZ ^i l^i] V cZl dcZ# 6alVnh
edh^i^dci]ZgZ[ZgZcXZYdi^ci]ZhVbZedh^"
i^dc l]Zc ^chiVaa^c\ V cZl ^chZgi id V^Y ^c
i]ZgdiVi^dcVahZfjZcX^c\#
6. AjWg^XViZi]ZIdgmhXgZli]gZVYhl^i]VhbVaa
Vbdjcid[a^\]ibVX]^cZd^a!l^eZi]ZZmXZhh
d[[! VcY idgfjZ i]Z hXgZl id Veegdm^bViZan
*%¶**^cX]$edjcYh#
7. Edh^i^dci]ZhigV^\]iZY\Zdci]Zdji[ZZYiVWaZ
VcY dkZg i]Z ^chZgi id bV`Z hjgZ i]Vi ^i ^h
^chiVaaZYXdggZXianVcYVii]ZhVbZ]Z^\]iVh
i]Zdi]Zg^chZgih#
·>[ i]Z ^chZgi ^h gV^hZY VWdkZ i]Z XdggZXi
]Z^\]i! gZbdkZ ^i VcY gZeZVi i]Z VWdkZ
egdXZYjgZjci^a^i^hegdeZgan^chiVaaZY#
Tools Needed Qty
9g^kZgl$I"'%Idgm7^i######################################## &
EgZX^h^dcHigV^\]iZY\Z###################################### &
To rotate or replace a spiral cutterhead
insert:
1. 9>H8DCC:8I?D>CI:G;GDBEDL:G
2. Eji dc ]ZVkn aZVi]Zg dg @ZkaVg \adkZh id
egdiZXindjg[^c\ZghVcY]VcYh#
3. GZbdkZVcnhVlYjhidgYZWg^h[gdbi]Z]ZVY
d[i]Z^chZgi!IdgmhXgZl!VcYi]ZhjggdjcY^c\
VgZV#
4. GZbdkZi]ZIdgmhXgZlVcYi]Z^chZgi!i]Zc
XaZVcVaaYjhiVcYYZWg^h[gdbWdi]eVgihVcY
i]ZedX`Zii]ZnlZgZgZbdkZY[gdb#
 Note: Proper cleaning of the insert, Torx
screw, and the cutterhead pocket is critical
to achieving a smooth finish. Dirt or dust
trapped between the insert and cutterhead
will raise the insert slightly, and make notice-
able marks on your workpiece the next time
you cut.
Tip: Use low-pressure compressed air or a
vacuum nozzle to clean out the cutterhead
pocket.
8. GZ"hZii]Zdji[ZZYiVWaZ]Z^\]iVh^chigjXiZY
^c i]Z Setting Outfeed Table Height dc
Page 43#
The outfeed table MUST be level with
cutterhead knives or inserts when they are
at top dead center (their highest point during
rotation). Otherwise, the workpiece cannot
properly feed past the cutterhead, which
may cause a kickback hazard to the opera-
tor.