MODELS G0747 & G0748 10" x 50" VERTICAL MILLING MACHINE w/POWER FEED OWNER'S MANUAL (For models manufactured since 8/12) Model G0747 Model G0748 Copyright © MARCH, 2013 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape Or form without the written approval of Grizzly Industrial, inc.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 3 Machine Description....................................... 3 Contact Info.................................................... 3 Manual Accuracy............................................ 3 Front View Identification................................. 4 Model G0747 Headstock Identification........... 5 Model G0748 Headstock Identification........... 6 G0747 Machine Data Sheet........................... 7 G0748 Machine Data Sheet..
SECTION 7: SERVICE.................................... 49 Troubleshooting............................................ 49 Adjusting Gibs............................................... 51 Adjusting Leadscrew Backlash..................... 52 X-Axis Leadscrew Backlash.............................. 52 Cross Leadscrew Backlash............................... 53 Tramming Spindle......................................... 54 SECTION 8: WIRING....................................... 56 Wiring Safety Instructions.......
INTRODUCTION Machine Description Manual Accuracy These milling machines are designed to remove material from a metal workpiece that is secured to the work table or a mill vise. The cutting tool is fixed to the rotating spindle and moved into the workpiece by lowering the spindle or moving the table. The table moves in three axes (X-, Y-, and Z-axis) with a power feed assist for the X-axis.
Front View Identification Headstock (see Pages 5–6) Motor Ram X-Axis Ball Handle Slotted Work Table X-Axis Ball Handle Power Feed Limit Switch X-Axis Power Feed Knee Crank Mounting Point (1 of 4) Y-Axis Ball Handle -4- Knee Model G0747/G0748 (Mfg.
Model G0747 Headstock Identification Belt Tension Adjustment Lever Motor High/Low Range Lever Motor Lock Lever Spindle Brake Belt Housing Safety Cover Spindle Switch Spindle Speed Range Selector Auto-Downfeed Rate Selector Manual/Power Downfeed Selector Auto-Downfeed Direction Pin Coarse Downfeed Lever Fine Downfeed Handwheel Quill Lock Lever Fine Downfeed Clutch Lever Adjustable Downfeed Stop Dial Indicator Rod Quill & Spindle To reduce your risk of serious injury, read this entire manual bE
Model G0748 Headstock Identification Motor Low Range Variable Speed Indicator Spindle Brake High Range Variable Speed Indicator Variable Speed Handwheel Spindle Switch Spindle Speed Range Selector Auto-Downfeed Rate Selector Manual/Power Downfeed Selector Auto-Downfeed Direction Pin Coarse Downfeed Lever Fine Downfeed Handwheel Fine Downfeed Clutch Lever Quill Lock Lever Adjustable Downfeed Stop Quill & Spindle -6- Dial Indicator Rod Model G0747/G0748 (Mfg.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0747 VERTICAL MILL - 16 SPEED Product Dimensions: Weight........................................................................................................................................................... 2,249 lbs. Width (side-to-side) x Depth (front-to-back) x Height............................................................... 54 x 66-1/2 x 84-3/4 in. Footprint (Length x Width)...
Main Specifications: Operation Info Spindle Travel.............................................................................................................................................. 5 in. Max Distance Spindle to Column........................................................................................................ 24-3/8 in. Max Distance Spindle to Table............................................................................................................ 16-7/8 in.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0748 VERTICAL MILL - VARIABLE SPEED Product Dimensions: Weight........................................................................................................................................................... 2,315 lbs. Width (side-to-side) x Depth (front-to-back) x Height............................................................... 54 x 66-1/2 x 84-3/4 in.
Main Specifications: Operation Info Spindle Travel.............................................................................................................................................. 5 in. Max Distance Spindle to Column........................................................................................................ 24-3/8 in. Max Distance Spindle to Table............................................................................................................ 16-7/8 in.
SECTION 1: SAFETY For your Own Safety, Read Instruction Manual before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. HAzARDOUS DUST. dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a niosh-approved respirator to reduce your risk. HEARING PROTECTION.
Additional Safety for Milling Machines UNDERSTANDING CONTROLS: The mill is a complex machine that presents severe cutting or amputation hazards if used incorrectly. Make sure you understand the use and operation of all controls before you begin milling. STOPPING SPINDLE: To reduce the risk of hand injuries or entanglement hazards, DO NOT attempt to stop the spindle with your hand or a tool. Allow the spindle to stop on its own or use the spindle brake.
SECTION 2: POWER SUPPLY Availability Circuit Requirements for 220V Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrican or qualified service personnel in accordance with all applicable codes and standards.
Grounding Instructions This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. the power cord and plug specified under “Circuit requirements for 220V” on the previous page has an equipment-grounding wire and a grounding prong.
SECTION 3: SETUP Unpacking Needed for Setup Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover any damage, please call us immediately at (570) 546-9663 for advice. The following are needed to complete the setup process, but are not included with your machine. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.
Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. Small Item Inventory: (Figure 2) Qty A. Front Way Cover........................................... 1 B. Rear Way Cover........................................... 1 C.
Cleanup The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Site Considerations Weight Load Physical Environment refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.
Lifting & Placing Note: After re-positioning the ram and headstock, make sure they are locked in place to prevent unexpected movement during lifting. Make sure the four turret lock bolts (two on either side of the ram, see Figure 6) are torqued to 47 ft/lbs. to keep the ram from unexpectedly moving from the force of the lifting straps. HEAVy LIFT! Straining or crushing injury may occur from improperly lifting machine or some of its parts.
Leveling & Mounting Generally, you can either bolt your machine to the floor or mount it on machine mounts. Although not required, we recommend that you secure the machine to the floor and level it while doing so. Because this is an optional step and floor materials may vary, hardware for securing the machine to the floor is not included. Bolting to Concrete Floors Anchor studs and lag shield anchors with lag screw (Figure 8) are two popular methods for anchoring an object to a concrete floor.
Assembly 4. Using the five cap screws pre-threaded into the holes, install the front way cover as shown in Figure 12. Assembly of the small components of the mill consists of attaching the ball handles, knee crank, and the way covers. To assemble the mill: 1. Remove the hex nuts from the X- and Y-axis leadscrews, then slide the ball handles (Figure 10) onto the leadscrews and secure them with the hex nuts. Note: Tighten the hex nuts just until they are snug.
Test Run After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its safety components, do not operate it further until you have resolved the problem. 7. Use the spindle switch to turn the mill ON. For Model G0747: Turn the spindle switch to the FLOW (forward low) position, as shown in Figure 14.
Power Feed Test Run The mill comes with a power feed unit for X-axis table travel. Proper operation of the limit switch attached to the front middle of the table is critical for the safe use of this power feed unit. If the power feed does not operate as expected during the following steps, disconnect it from power and contact our Tech Support at (570) 546-9663 for assistance. To test the power feed: 1. Make sure all tools, cables, and other items are well clear of table movement as you follow these steps.
Spindle Break-In Complete the spindle bearing break-in procedure to prevent rapid wear and tear of spindle components once the mill is placed into operation. The bearings and gears used in the mill are manufactured to very close tolerances. Before operational stress is placed on these and other moving parts in the mill, complete this break-in procedure to conform these components to one another and ensure trouble-free performance from the mill. To perform the spindle break-in procedure: 1.
SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand. Due to the generic nature of this overview, it is not intended to be an instructional guide.
Table Movement Index Rings The mill table moves in three directions, as illustrated in Figure 16: • X-axis (longitudinal) • Y-axis (cross) • Z-axis (vertical) These movements are controlled by table ball handles and the Z-axis crank. Additionally, the table can be moved along the X-axis with the power feed. Figure 17. Locations of index rings.
X-Axis Power Feed Identification The mill is equipped with a power feed unit for X-axis table movement. Refer to Figure 19 and the descriptions below to understand the functions of the various components of the power feed system. A. Limit Switch. Stops table movement when either of the switch side plungers are pressed by the limit stops. B. Limit Stop. Restricts table movement by its positioning along the front of the table. C. Graduated Index Ring. Displays the distance of table travel in 0.
X-Axis Power Feed Operation Tool Needed Qty Hex Wrench 8mm................................................ 1 Head Movement The head tilts 45° forward or backward, and rotates 90° left or right (see Figures 20–21). To operate the X-axis power feed: 1. Loosen the X-axis table locks (refer to Figure 18 on Page 27 for locations). 2. Secure the limit stops if needed to restrict table movement. Note: Make sure the cap screws firmly secure the limit stops in place when positioned. 3.
Rotating Head Left/Right The head is heavy. When tilting or rotating the head, get help to support the weight as you use the controls. Tilting Head Forward/Backward 1. DISCONNECT MILL FROM POWER! 2. Loosen the four lock bolts shown in Figure 23. Rotation Bolt 1. DISCONNECT MILL FROM POWER! 2. Loosen the three tilt lock bolts shown in Figure 22. Lock Bolts Tilt Bolt Figure 23. Head rotation controls. Lock Bolts 3.
Ram Movement The ram travels forward or backward 24" and rotates 360° around the turret. Tool Needed Qty Wrench 19mm..................................................... 1 Moving Ram Forward/Backward 1. DISCONNECT MILL FROM POWER! 2. Loosen the two lock bolts shown in Figure 24. Always lock the ram firmly in place after moving it. Unexpected movement of the ram and head during operations could damage the cutter or workpiece. Rotating Ram 1. DISCONNECT MILL FROM POWER! 2.
Spindle Speed Using the correct spindle speed is important for safe and satisfactory results, as well as maximizing tool life. To set the spindle speed for your operation, you will need to: (1) Determine the best spindle speed for the cutting task, and (2) configure the mill controls to match the closest spindle speed.
Setting Model G0747 Spindle Speed 3. The Model G0747 has 16 spindle speeds—eight in low motor speed and eight in high motor speed. Setting the spindle speed involves: 1) Selecting the spindle speed range, 2) positioning the V-belt, and 3) setting the spindle switch. High-Low Range Lever To set the Model G0747 spindle speed: 1. Move the high-low range lever shown in Figure 28 to the high or low position. High Low Make sure the spindle is completely stopped. 2.
6. Loosen the two motor lock levers, one on each side of the head, then pull the belt tension adjustment lever forward to release the V-belt tension. Note: As displayed in Figure 30, the Model G0747 has two spindle speeds for each V-belt position depending on the spindle switch setting. 7. Refer to the illustrations in Figure 30, and position the V-belt on the pulleys for the desired spindle speed. 8.
Setting Model G0748 Spindle Speed The Model G0748 has variable spindle speeds from 60 to 4200 RPM. Setting the spindle speed involves 1) Selecting the spindle speed range, and 2) using the variable-speed handwheel to select the spindle speed. To set the Model G0748 spindle speed: 1. For the Model G0748 ONLY, always make sure that the spindle rotation has started and is at a constant speed before using the variable-speed handwheel to adjust the spindle speed.
Spindle Downfeed Spindle downfeed movement on the mill is controlled by three mechanisms: 1) The coarse downfeed lever, 2) the fine downfeed handwheel, and 3) the auto-downfeed system. When spindle rotation is reversed, either by changing the spindle speed range or by using the spindle direction switch, the direction of spindle auto-downfeed will reverse. D. Fine Downfeed Clutch Lever. Engages the fine/auto-downfeed gears.
Coarse Downfeed Use the coarse downfeed lever to quickly move the spindle manually. To use the coarse downfeed: 1. Make sure the spindle is completely stopped. 2. Pull the downfeed selector knob out, then rotate it clockwise until the knob pin seats in the forward manual (disengaged) detent (see Figure 35). Note: It may be necessary to turn the spindle by hand as you move the selector to enable the gears to mesh. Manual (Disengaged) Position 4.
Auto-Downfeed When using the auto-downfeed system, the spindle will move in the direction you choose with the auto-downfeed direction pin. When the quill dog reaches the top or meets the downfeed stop, the downfeed clutch lever will release. Then, if the spindle was traveling upward, the movement will simply stop. If the spindle was traveling downward, then the spindle will move back to the top at a rate controlled by the return spring on the left side of the head. 4.
Spindle Brake ALWAYS start spindle rotation before using auto-downfeed to avoid the risk of gear damage. 7. Select one of the three downfeed rates by pulling the knob of the auto-downfeed rate selector out, position the selector over the appropriate detent, then release the knob. Make sure the pin is firmly seated by attempting to move the selector without pulling the knob out. Note: Refer to the illustration in Figure 38 when selecting the downfeed rate.
Loading/Unloading Tooling 5. With one hand holding the tool in place, insert the drawbar into the spindle from the top of the head, then thread it into the tool (see Figure 42). The mill is equipped with an R8 spindle taper and a 7⁄ 16"-20 x 23 1⁄ 2" spindle drawbar (see Figure 41). Head of Drawbar Figure 42. Drawbar loaded (Model G0747 shown). Figure 41. Upper portion of drawbar. Tools Needed Qty Wrench 21mm..................................................... 1 Brass Hammer..........................
ACCESSORIES SECTION 5: ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. G1076—52-PC. Clamping Kit This clamping kit includes 24 studs, six step block pairs, six T-nuts, six flange nuts, four coupling nuts, and six end hold-downs. The rack is slotted so it can be mounted close to the machine for easy access.
G7155—6" Precision Milling Vise This swiveling milling vise features perfectly aligned, precision-ground jaws, robust clamping screws, and easy-to-read 0°–360° scales. T23962—ISO 68 Moly-D Machine Oil, 5 gal. T23963—ISO 32 Moly-D Machine Oil, 5 gal. Moly-D oils are some of the best we've found for maintaining the critical components of machinery because they tend to resist run-off and maintain their lubricity under a variety of conditions—as well as reduce chatter or slip.
SECTION 6: MAINTENANCE Daily, After Operations To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.
Lubrication The mill has numerous moving metal-to-metal contacts that require regular and proper lubrication to ensure efficient and long-lasting operation, and to protect your investment. Other than the lubrication points covered in this section, all other bearings are internally lubricated and sealed at the factory. Simply leave them alone unless they need to be replaced.
Table Ways (One-Shot Oiler) Headstock Gearing Oil Type....... Model T23962 or ISO 68 Equivalent Oil Amount.................... One Pull of Pump Handle Check/Add Frequency.........4–8 hrs. of Operation Grease Type.........................NLGI 2 or Equivalent Grease Amount..........Two Pumps of Grease Gun Check/Add Frequency........... 40 hrs. of Operation The one-shot oiler is connected to a series of aluminum tubes that carry the lubricant to wear points along the table horizontal and vertical ways.
Ram Ways Table Elevation Leadscrew Oil Type....... Model T23962 or ISO 68 Equivalent Oil Amount............................................. Thin Coat Check/Add Frequency........... 40 hrs. of Operation Grease Type.........................NLGI 2 or Equivalent Grease Amount..................................... Thin Coat Check/Add Frequency........... 40 hrs.
Power Feed Gears 5. Grease Type.........................NLGI 2 or Equivalent Grease Amount..........Two Pumps of Grease Gun Check/Add Frequency......... 160 hrs. of Operation Brush a light coat of lubricant on the teeth of the bevel gear and the smaller drive gear (see Figure 61). Brass Bevel Gear Qty Tool Needed Wrench 19mm..................................................... 1 To lubricate the power feed gears: 1. DISCONNECT MILL FROM POWER! 2.
Machine Storage To avoid rust problems or corrosion damage, use the following information to protect your investment when storing the mill for any length of time. • Loosen the belts to prevent them from stretching during storage. Post a reminder on the mill that the belts need to be re-tensioned before resuming operations. • Cover and place the machine in a dry area that is out of direct sunlight and away from hazardous fumes, paint, solvents, or gas.
SECTION 7: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Symptom Possible Cause Possible Solution Machine does not start or a breaker trips. 1. Plug/receptacle at fault or wired incorrectly. 2.
Symptom Possible Cause Possible Solution Tool slips in collet. 1. Collet not fully drawn into spindle taper. 2. Wrong size collet. 3. Debris on mating surface of collet and spindle. 4. Excessive depth of cut. 1. Snug up drawbar to fully seat collet. 2. Use correct collet for tool shank diameter. 3. Remove oil and debris from mating surface, then re-install. 4. Decrease depth of cut and allow chips to clear. Tool breakage. 1. Spindle speed too slow or feed rate too fast. 2. Tool getting too hot. 1.
Adjusting Gibs Gibs are tapered lengths of metal that are sandwiched between two moving surfaces. Gibs control the gap between these surfaces and how they slide past one another. Correctly adjusting the gibs is critical to producing good milling results. Tight gibs make table movement more accurate but stiff. Loose gibs make moving the table sloppy but easier to do. The goal of gib adjustment is to remove unnecessary sloppiness without causing the ways to bind.
Adjusting Leadscrew Backlash Leadscrew backlash is the amount of motion the leadscrew rotates before the attached device begins to move. X-Axis Leadscrew Backlash 1. DISCONNECT MILL FROM POWER! 2. Loosen the two cap screws on the X-axis leadscrew nut accessed from underneath the left side of the table (see Figure 65). Leadscrews will always have a certain amount of backlash that will increase with normal wear. Generally, 0.005"–0.
Cross Leadscrew Backlash 1. DISCONNECT MILL FROM POWER! 5. Loosen the two cap screws on the face of the leadscrew nut shown in Figure 68. 2. Remove the hex nut and ball handle from the Y-axis leadscrew. Note: In the next step, take care not to misplace the leadscrew key as you remove the parts. 3. Unthread and remove the knurled retaining ring, graduated dial ring, and the leadscrew key (see Figure 66). Y-Axis Leadscrew Nut & Cap Screws Figure 68. Y-axis leadscrew nut and cap screws. 6.
Tramming Spindle After positioning the head at an angle and when your operation requires that the spindle axis be precisely perpendicular to the table, you must tram or align the spindle with the table to ensure the spindle is exactly 90° to the table. This procedure involves mounting a dial test indicator to the quill or spindle, rotating it around the table, and adjusting the spindle axis (Z-axis) 90° to the table X- and Y-axes, as illustrated in Figure 69. Spindle 9 90º 0º 1.
5. To measure spindle alignment along the X-axis, place the parallel block directly under the spindle and indicator across the length of the table, as illustrated in Figure 71. Note: If you must re-position the quill or the knee to accommodate the above step, then review the tasks in Step 2 to make sure the mill is properly prepared for tramming. Table (Top View) Note: Keep one of the rotation lock bolts just snug so the head does not move loosely while you adjust it.
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
G0747 Wiring Diagram Hot Ground SPINDLE SWITCH G Hot X 220 VAC 3-Phase NEMA 15-15 Plug (As Recommended) Z W Hot Ground MOTOR 5 2U T R S T R FRONT 4 2W S 6 5 3 2 4 1 6 5 3 2 4 1 6 2V Ground 1V 1W 1U 1 Model G0747/G0748 (Mfg.
G0748 Wiring Diagram Hot Ground SPINDLE SWITCH G Hot X S 220 VAC 3-Phase NEMA 15-15 Plug (As Recommended) Z W Hot 8 V 7 3 Ground FRONT T S R T S R W 6 U T R MOTOR 1U 2U 2W 1W R 1V 2V S T Ground -58- READ ELECTRICAL SAFETY ON PAGE 56! Model G0747/G0748 (Mfg.
SECTION 9: PARTS Main 8 4 7 6 2 9 10 17 126 125 1 13 14 16 15 23 127 128 129 133 18 19 37 38 39 40 41 49 50 124 33 31 43 123 120 118 52 53 42 55 46 56 57 58 64 47 51 48 44 62 119 131 32 132 60 54 98 105 61 65 75 69 74 76 104 77 71 80 82 103 102 135 134 81 138 90 79 135 91 137 93 136 83 84 96 85 86 87 88 89 92 94 95 Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are
Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 4 6 7 8 9 10 13 14 15 16 17 18 19 23 31 32 33 37 38 39 40 41 42 43 44 46 47 48 49 50 51 52 53 54 55 56 57 58 60 61 62 64 65 69 QUILL HOUSING ADJUSTMENT GEAR RAM ADAPTER LIFTING EYE BOLT 28MM DIA M10-1.5 X 35 HEAD TILT ADJUSTING WORM THRUST WASHER 14MM HEAD TILT ADJUSTING WORM SHAFT KEY 5 X 5 X 50 RAM CASTING CAP SCREW M8-1.25 X 30 ROLL PIN 6 X 30 HEAD TILT SCALE STEEL FLUTED RIVET 2 X 5MM RAM ADAPTER PIVOT BOLT M28.5 X 181.
X- & Y-Axis Leadscrews 212 214 221 209 206 220 222 210 229 226 209 216 211 215 218 210 205 224 214 205 204 218 208 203 201 229 204 226 223 216 202 202 203 216 219 201 217 205 209 207 208 229 214 201 203 227 217 209 228 210 226 202 208 207 206 REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 203 204 205 206 207 208 209 210 211 212 214 215 HEX NUT 1/2-13 BALL CRANK HANDLE DIAL LOCK NUT GRADUATED DIAL DIAL HOLDER CAP SCREW M6-1 X 16 BEARING RETAINER RING BALL BE
Downfeed System 312 314 311 302 303 304 307 308 301 305 306 495 313 315 317 327 336 349 348 342 343 359 360 362 366 367 371 369 368 370 372 373 375 376 377 374 378 400 397 398 396 395 401 399 403 404 405 320 319 328 493 347 318 309 310 494 344 316 338 350 340 351 491 492 481 482 489 488 490 487 486 484 352 485 476 477 483 355 475 455 386 387 392391 390 380 394 379416 393 417 415 414 413 412 419 406 407 409 408 411 410 424 425 469 471 465 468 478 466 480 384 385 3
Downfeed System Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 327 328 329 331 332 333 334 335 336 337 338 340 341 342 343 344 347 348 349 350 351 352 355 356 357 359 360 361 PHLP HD SCR 10-24 X 1-3/4 BEVEL PINION FLAT WASHER FEED BEVEL PINION FEED WORM GEAR SHAFT SLEEVE WORM CRADLE BUSHING SET SCREW 1/4-20 X 1/2 WORM CRADLE SPACER FEED DRIVE WORM GEAR FEED DRIVE WORM GEAR SHAFT KEY 3 X 3 X 10
Downfeed System Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 417 418 419 420 421 423 424 425 427 428 429 430 431 432 433 434 435 436 437 438 440 441 442 444 445 446 448 451 452 453 455 456 457 458 ROLL PIN 3 X 20 CAM ROD SLEEVE ASSEMBLY ROLL PIN 3 X 12 COMPRESSION SPRING TRIP PLUNGER TRIP PLUNGER BUSHING FEED TRIP PLUNGER FINE DOWNFEED HANDWHEEL ASSY SPINDLE QUILL SKIRT SPINDLE SPANNER NUT SPANNER NUT LOCK WASHER BALL BEARING 6206ZZ SPINDLE SLEEVE QUILL NOSE PIECE LOWER SPINDLE SEAL 64 X 35
G0747 Headstock 586 586-1 586-4 586-3 586-2 501 530 529 503 504 586-5 539 531 532 533 529 534 535 505 506 541 509 542 507 510 508 511 512 515 513 516 517 551 514 543 585 550 545 518 546 519 528 527 559 555 524 520 557 549 560 525 556 561 562 564 558 565 524 522 566 567 563 578 579 568 523 581 569 571 572 573 574 Model G0747/G0748 (Mfg.
G0747 Headstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 501 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 522 523 524 525 527 528 529 530 531 532 533 534 535 539 541 542 543 545 546 549 DRAWBAR 7/16-20 X 23-1/2 UPPER BEARING LOCK NUT BEARING SLEEVE LOCK NUT BALL BEARING 6207ZZ SMALL UPPER BEARING SPACER LARGE UPPER BEARING SPACER BALL BEARING 6207ZZ COMPRESSION SPRING SET SCREW M6-1 X 12 SPINDLE PULLEY BEARING SLEEVE HEX NUT 5/16-18 EXT TOOTH WASHER 5/16 BRAKE
G0748 Headstock 501-1 501-2 604 537 607 609 501 501-4 605 606 501-5 501-3 506 610 614 504 613 612 599 597 616 509 598 596 615 594 595 578 536 593 537 560 577 579 508 602 601 600 611 580 576 574 561 562 584 556 592 554 555 543 573 552 572 571 550 570 591 587 590 588 589 545 562 570 585 558 564 565 511 583 530 531 529 528 527 557 539 540 556 541 563 566 567 533 512 556 575 535 534 510 538 559 582 502 507 617 513 526 525 523 514 521 520 519
G0748 Headstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 501 501-1 501-2 501-3 501-4 501-5 502 504 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 523 525 526 527 528 529 530 531 533 534 535 536 537 538 539 540 541 543 545 546 547 548 549 550 551 552 P07480501 P07480501-1 P07480501-2 P07480501-3 P6205ZZ P6205ZZ P07480502 P6009ZZ PCAP02M P07480507 P07480508 P07480509 P07480510 PCAP31M P07480512 P07480513 P07480514 P07480515 P07480516 P07480517 P07480518 PCAP68M PS03M P07
G0748 Headstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 609 610 611 612 613 HEADSTOCK FRONT COVER, ALUMINUM CAP SCREW M6-1 X 30 CAP SCREW M6-1 X 16 BRASS SLEEVE SPEED CHANGE DIAL 614 615 616 617 SPEED CHANGE INDICATOR PLATE CAP SCREW M6-1 X 12 ACORN NUT 5/16-18 BRAKE PIVOT ARM P07480609 PCAP07M PCAP01M P07480612 P07480613 Model G0747/G0748 (Mfg.
One-Shot Oiler 709 703 706 703 709 702 706 705 704 702 701 704 707 702 706 708 704 REF PART # DESCRIPTION REF PART # DESCRIPTION 701 702 703 704 705 OILER PUMP AND RESERVOIR ALUMINUM PIPE 4MM ELBOW OIL DISTRIBUTOR CPS4 CAP SCREW M6-1 X 20 A-TYPE OIL DISTRIBUTOR A4 706 707 708 709 ELBOW OIL DISTRIBUTOR CPS3 FLEXIBLE STEEL TUBE A-TYPE OIL DISTRIBUTOR A8 ELBOW OIL DISTRIBUTOR CPS5 -70- P07470701 P07470702 P07470703 PCAP02M P07470705 P07470706 P07470707 P07470708 P07470709 Model G0747/G0748
Accessories 805 802 803 801 804 REF PART # DESCRIPTION REF PART # DESCRIPTION 801 802 803 BOTTLE FOR OIL WRENCH 17 X 19MM CLOSED ENDS STANDARD SCREWDRIVER #2 804 805 PHILLIPS SCREWDRIVER #2 TOOLBOX P07470801 PWR1719C PSDF2 Model G0747/G0748 (Mfg.
G0747 Machine Labels & Cosmetics 902 901 903 904 913 912 911 910 906 909 908 905 904 907 REF PART # DESCRIPTION REF PART # DESCRIPTION 901 902 903 904 905 906 907 MODEL NUMBER LABEL 220V 3-PHASE ELECTRICITY LABEL SMALL GRIZZLY NAMEPLATE ELECTRICITY LABEL MACHINE ID LABEL GRIZZLY GREEN TOUCH-UP PAINT GOGGLES/FACE SHIELD LABEL 908 909 910 911 912 913 220V DISCONNECT LABEL ENTANGLEMENT LABEL READ MANUAL LABEL QUILL FEED LABEL SPEED RANGE LABEL SPINDLE SPEED LABEL P07470901 P07470902 G8588 PLAB
G0748 Machine Labels & Cosmetics 901 903 904 912 911 910 909 906 908 905 907 904 REF PART # DESCRIPTION REF PART # DESCRIPTION 901 903 904 905 906 907 MODEL NUMBER LABEL SMALL OBLONG GRIZZLY NAMEPLATE ELECTRICITY LABEL MACHINE ID LABEL GRIZZLY GREEN TOUCH-UP PAINT GOGGLES/FACE SHIELD LABEL 908 909 910 911 912 220V DISCONNECT LABEL ENTANGLEMENT LABEL READ MANUAL LABEL QUILL FEED LABEL SPEED RANGE LABEL P07480901 H4609 PLABEL-14A P07480905 PPAINT-1 P07471007 Model G0747/G0748 (Mfg.
-74- Model G0747/G0748 (Mfg.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
