MODEL G0472/G0473/G0476 SANDBLASTING CABINET OWNER'S MANUAL G0472 G0473 G0476 COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED MAY 2006. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .................................................................................................................................... 2 Contact Info ................................................................................................................................ 2 Machine Data Sheet............................................
INTRODUCTION Foreword Contact Info We are proud to offer the Model G0472/G0473/ G0476 Sandblasters. These machines are a part of a growing Grizzly family of fine wood and metalworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
MACHINE DATA Machine Data Sheet SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G0472 SANDBLASTING CABINET Design Type ...................................................................................................... Floor Model General Specifications: Width ........................................................................................................................36" Height .............................................................
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. 10. NEVER LEAVE WHEN MACHINE IS RUNNING.
Additional Safety Instructions for Sandblasters 1. CORRECT ABRASIVES. Never use wet abrasives in this sandblaster, it is designed for dry abrasives only. 2. PROTECTING LUNGS. Make sure that you always use a respirator when using or cleaning the sandblaster. 3. LEAVING THE AREA. Always disconnect air supply when leaving the sandblaster. 4. PROTECTING EYES. Make sure that you always use safety glasses when using or cleaning the sandblaster. 5. PROTECTING ENVIRONMENT.
SECTION 2: SET UP Set Up Safety This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Unpacking The Model G0472/G0473/G0476 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
G0472 Assembly 4. To assemble the sandblaster: 1. Install the four legs onto the stand frame with 12 M6-1x20 screws and nuts (Figure 1). 5. Figure 1. Stand frame. 2. Install the lamp and wiring with the M4-0.7 x 10 screws, washers, and nuts. Use the zipties to lock the lamp to the two lamp supports (Figure 4). Assemble the hopper assembly, the screen, and the adhesive foam gasket in the order shown (Figure 2). Figure 4. Electrical installation.
G0473 Assembly 3. To assemble the sandblaster: 1. Install the bulkhead fitting with gasket. Attach the air supply hose and suction hose to the bulkhead fittings and suction pipe with hose clamps (Figure 3). Install the filter assembly with the screws and nuts (Figure 1). Bulkhead Fitting Suction Hose Suction Pipe Figure 1. Filter installation. 2. Install the gloves as shown in Figure 2. Figure 2. Glove installation. G0472/G0473/G0476 Sandblasters 4. Seal Supply Hose Washer Washer Figure 3.
G0476 Assembly 5. Install window, hinges, lock latches, and the knob (Figure 5). To assemble the sandblaster: 1. Install the two lamp holders with the two screws (Figure 1). Figure 5. Hinge and knob assembly. 6. 2. Install the chain to the window and cabinet with the screws and nuts (Figure 6). Figure 1. Lamp holder. Connect the electrical wires and install the electrical box with the screws (Figure 2). Chain Figure 5. Window chain. 7. Figure 2. Light assembly. 3.
SECTION 3: OPERATIONS Sandblasting presents a real hazard of silicosis and other lung contamination injuries! These Injuries are permanent and can get worse over time. If you use sandblasting equipment without the proper protection, your lungs and eyes may become irreversibly contaminated. DO NOT use this sandblaster unless you know how to use it and protect yourself correctly. For types of protective equipment and acceptable respirator types, contact your local OSHA or NIOSH office. Operation Safety 4.
Abrasive Options Blasting Media from Grizzly.Com PART # G6535: 15 G6536: 15 G6537: 15 G6538: 15 lbs. lbs. lbs. lbs. Aluminum Oxide 220 Grit. Aluminum Oxide 120 Grit. Aluminum Oxide 60 Grit. Glass Bead 50-Micron Grit. Below is a basic introduction to some of the most common blasting abrasives. Refer to magazines, trade articles, professionals, and the abrasive manufacturer for the specific surfaces that can be addressed with a type of abrasive.
Notes G0472/G0473/G0476 Sandblasters -13-
SECTION 4: PARTS Parts Breakdown (G0472) �� �� �� �� �� �� ���� �� �� �� �� �� �� �� �� �� �� �� �� �� � � �� �� �� ���� �� �� �� ��� ���� � �� �� � �� ��� ���� ���� � �� �� � �� �� �� �� � �� �� �� �� �� � � � -14- � G0472/G0473/G0476 Sandblasters
Parts List (G0472) REF PART # DESCRIPTION REF PART # DESCRIPTION 1 1-1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15-1 16 17 18 18-1 19 20 21 21-1 22 23 P0472001 P0472001-1 P0472002 P0472003 P0472004 P0472005 P0472006 P0472007 P0472008 P0472009 P0472010 P0472011 P0472012 P0472013 P0472014 P0472015 P0472015-1 P0472016 P0472017 P0472018 P0472018-1 P0472019 P0472020 P0472021 P0472021-1 P0472022 P0472023 CABINET ASSEMBLY DOOR SEAL SCREEN FRAME MESH SCREEN RIGHT LEG LEFT LEG HOPPER SUCTION PIPE LEFT DOOR RIGHT DO
Parts Breakdown (G0473) ��� ��� ����� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ����� -16- G0472/G0473/G0476 Sandblasters
Parts List (G0473) REF PART # DESCRIPTION REF PART # DESCRIPTION 101 102 104 105 108 109 115 116 117 118 119 120 121 122 123 124 125 126 127 127-1 128 129 130 131 132 133 P0473101 P0473102 PN01M P0473105 PS14M PN01M P0473115 P0473116 P0473117 P0473118 P0473119 PS38M P0473121 P0473122 P0473123 PS38M PN04M PW05M P0473127 P0473127-1 P0473128 P0473129 P0473130 P0473131 P0473132 P0473133 WINDOW FRAME AND SEAL WINDOW PLEXIGLASSS 6MM FLAT WASHER HINGE PHLP HD SCR M6-1 X 12 HEX NUT M6-1 CABINET RIGHT DOOR L
Parts Breakdown (G0476) ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ����� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� -18- ��� ��� ��� ��� ��� ��� G0472/G0473/G0476 Sandblasters
Parts List (G0476) REF PART # DESCRIPTION REF PART # DESCRIPTION 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 P0476101 P0476102 PN01M PN01M P0476105 PHTEK15M P0476107 PS14M PN01M P0476110 PW03M P0476112 PS14M P0476114 P0476115 P0476116 P0476117 P0476118 P0476119 PS38M P0476121 P0476122 P0476123 PS38M PN04M PW05M P0476127 WINDOW KNOB HEX NUT M6-1 6MM FLAT WASHER HINGE TAP SCREW M4 X 10 CHAIN PHLP HD SCR M6-1 X 12 HEX NUT M6-1 LOCK LEVER F
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email ________________________ Invoice # _________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.