2" HORIZONTAL RESAW BANDSAW MODEL G0503 Instruction Manual Copyright © august, 2004 By Grizzly Industrial, Inc., REVISED MAY, 2011 (TS) Warning: No portion of this manual may be reproduced in any shape or form without the written approval of Grizzly Industrial, inc.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................................................................................................ 3 Foreword..................................................................................................................................... 3 Contact Info................................................................................................................................. 3 Identification................................................
SECTION 5: ACCESSORIES.......................................................................................................... 32 SECTION 6: MAINTENANCE......................................................................................................... 35 Cleaning.................................................................................................................................... 35 Miscellaneous............................................................................................
INTRODUCTION Manual Accuracy Contact Info We are proud to offer this manual with your new machine! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the machine we used when writing this manual. However, sometimes we still make an occasional mistake. We stand behind our machines. If you have any questions or need help, use the information below to contact us. Before contacting, please get the serial number and manufacture date of your machine.
A D B E C Figure 1. Main view of machine features and controls. Identification A. Infeed Pressure Rollers—Maintain downward pressure on the board to keep it steady during cutting. B. Return Rollers—Allows the person receiving the newly cut board to return it to the operator without walking around the saw. -4- C. Infeed Conveyor—Moves the board through the bandsaw blade during cutting. D. Control Panel—Controls power to the main motor and the hydraulic motor. For more details, see page 6. E.
L F Q J G H K P I M N O Figure 2. Back and side views of machine features and controls. Main Motor—Drives the saw wheels for blade movement and drives the hydraulic pump for conveyor movement. L. Head Elevation Handwheel—Moves the head (the part of the saw that contains the wheels and blade) up or down as needed. G. Hydraulic System Oil Cooler—Cools the hydraulic fluid for the hydraulic system. M. Electrical Control Box—Main area for wiring, rewiring, and changing the fuses.
Control Panel E D F C A B Figure 3. Control panel close-up. A. EMERGENCY STOP Button—Turns off power to both motors in an emergency. D. MOTOR START Button—Starts the main motor and the saw blade. B. PUMP STOP Button—Stops the hydraulic pump motor. E. PUMP START Button—Starts the hydraulic pump motor. C. MOTOR STOP Button—Stops the main motor. F. POWER ON Button—Connects power to both motors. -6- Model G0503 (Mfg.
MACHINE DATA sheet Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 Model G0503 12" Horizontal Resaw Bandsaw Design Type..................................................................................... Horizontal Floor Model Overall Dimensions: Conveyor Table...............................................................................................12"W x 107"D Height From Floor To Table........................................................................
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions for Machinery 7. Only allow trained and properly supervised personnel to operate machinery. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. 10. NEVER LEAVE WHEN MACHINE IS RUNNING.
Additional Safety Instructions for Resaws 1. 2. EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Contact our Service Department at (570) 546-9663. 8. BLADE TENSION. Make sure blade is properly tensioned before operating machine. 9. BLADE SPEED. Blade should be running at full speed before beginning a cut. ENTANGLEMENT. Keep loose clothing and long hair away from moving conveyors! 10. CONVEYOR SPEED.
Additional Safety Instructions for Hydraulics 1. HYDRAULIC INJECTION HAZARDS. Be familiar with the hazards of hydraulic injection injuries. • Leaking hydraulic fluid may have enough pressure to penetrate skin. Never use your hands to check for suspected hydraulic leaks. 4. CHECKING FOR LEAKS. Use a piece of cardboard to check for suspected hydraulic leaks. Pressurized hydraulic fluid may cause injection injuries and can be extremely hot. Never use your hands to check for suspected hydraulic leaks. 5.
SECTION 2: CIRCUIT REQUIREMENTS 220V 3-Phase 440V 3-Phase Serious personal injury could occur if you connect your machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so. Serious personal injury could occur if you connect your machine to the power source before you have completed the setup process. DO NOT connect the machine to the power source until instructed to do so.
Connection Type Because of the high amperage draw from this machine, we recommend that you hardwire it directly to your circuit breaker and install a locking shut-off lever (see Figure 4) near the machine as a way to quickly disconnect the power and prevent accidental starting. We DO NOT recommend using an extension cord with this machine. Grounding In the event of an electrical short, grounding reduces the risk of electric shock by providing a path of least resistance to disperse electric current.
SECTION 3: SET UP About this Section Piece Inventory The purpose of this section is to guide you through the required steps to get your machine out of its crate and into operating condition. The inventory of the shipping crate includes: • Resaw......................................................... 1 • Bandsaw Blade 168" x 1" x 0.035".............. 1 • Handwheel Handle...................................... 1 • Blade Cover................................................. 1 • Tool Box....................
Hardware Recognition Chart Model G0503 (Mfg.
Items Needed for Set Up ITEM Clean Up QTY Forklift................................................................ 1 Citrus-Based Degreaser or Solvent........... Varies Metal Protectant......................................... Varies Hammer Drill...................................................... 1 Air Compressor.................................................. 1 Vacuum.............................................................. 1 Punch 1⁄2"...........................................................
Site Considerations Floor Load The Model G0503 weighs 1870 lbs. and has a base footprint of 40"W x 391⁄4"L. The floor where this machine will be installed must be level and structurally sound. Most commercial floors are suitable for your machine. Some floors may require additional reinforcement.
Mounting Resaw to the Floor Mounting the Conveyor Belt We recommend that you bolt your new resaw to the floor. Because this is optional and floor materials may vary, floor mounting hardware is not included. It may be necessary to level the floor before installing this machine. Tools Needed Qty Wrench/Socket 17mm . ..................................... 1 Note—The instructions below are given for a typical heavy-duty shop floor made of 6" thick concrete.
Attaching the Hydraulics 4. Line up the holes and insert the carriage bolts as shown in Figure 9. Tools Needed Qty Wrench/Socket 19mm ....................................... 1 Wrench/Socket 17mm ....................................... 1 The hydraulic hoses and fittings are capped for protection during shipping and labeled with an "A" or a "B" for ease of assembly. To attach the hydraulic drive to the conveyor: Figure 9. Carriage bolt placement. 5.
Installing the Blade Cover Attaching the Handwheel Handle Tools Needed Qty Wrench/Socket 10mm ....................................... 1 Tools Needed Qty Wrench/Socket 19mm ....................................... 1 Hardware Needed Qty Carriage Bolt M6-1.0 x 16................................... 4 Flat Washer 6mm............................................... 4 Lock Nut M6-1.0................................................. 4 Hardware Needed Qty Handwheel Handle..........................................
Positioning the Control Panel Mounting the Return Rollers Tools Needed Qty Hex Wrench 8mm ............................................. 1 Tools Needed Qty Wrench/Socket 17mm ....................................... 1 To mount the control panel: To mount the return rollers: 1. Unwrap the protective covering from the control panel and support arm. 1. Remove all four bolts shown in Figure 16. 2. Place the control panel support arm into the mounting bracket as shown in Figure 14.
Connecting to the Dust Collector Installing the Blade To be effective, the dust collection system that you connect to the resaw must be able draw a minimum of 1500 CFM at the point where you connect the hoses to the resaw. Note—This number is an approximation and has been provided for estimation purposes only. Tools Needed Qty Phillips Head Screwdriver ................................. 1 Hardware Needed Qty Dust Collection Hoses 4"................................... 3 Hose Clamps..........................
5. Carefully fit the blade over each wheel, and position it between the blade guides as shown in Figure 20. Make sure the teeth point toward the right-hand side of the machine, as you are facing the front. 7. Hand tighten the handle until the set plate comes in contact with the sleeve shown in Figure 22. Sleeve Set Plate Figure 22. Blade tensioning handle. Figure 20. Blade positioned between guides. 6.
Connecting to Power 2. Connect the power wires to the main terminal shown in Figure 23. Because of the high amperage draw from this machine, we recommend that you hardwire it directly to your circuit breaker and install a locking power disconnect lever near the machine. See page 12 for wiring recommendations. If you have performed all of the previous set up instructions, you are ready to connect the resaw to the power source. Tools Needed Qty Phillips Head Screwdriver .................................
Test Run 4. Turn the POWER ON switch (shown in Figure 24) clockwise. Before starting the resaw, perform the preceding assembly and adjustment instructions, and read and understand the entire manual. Failure to follow this warning could result in serious personal injury or death! 5. Press the MOTOR START button and immediately press the EMG STOP button. As you are standing in front of the machine, make sure that the blade is moving from left to right.
Blade Tension 4. Hand tighten the handle until the set plate contacts the sleeve shown in Figure 27. Sleeve The only way to accurately tension the blade on this machine is with a blade tensioner such as the Model H5408 on page 33. This method is for rough blade tensioning only. Set Plate Tools Needed Qty Hex Wrench 4mm ............................................. 1 Wrench/Socket 17mm . ..................................... 2 To adjust the tension: 1. Disconnect the resaw from power! 2.
SECTION 4: OPERATIONS Operation Safety Eyes, lung, and ear damage could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing and long hair away from moving machinery. Stock Preparation Always make sure that any stock you plan on cutting is clean and free of nails, staples, or embedded stones.
Blade Height Conveyor Controls The blade height is the distance between the conveyor table and the bottom of the blade. The Model G0503 features a variable speed infeed conveyor to move lumber through the blade. Slow the conveyor speed to get a smooth cut on hard wood, and speed it up for softer woods. NOTICE The resaw blade may come into contact with the conveyor belt if lowered below 1⁄4". 1. Push the PUMP START button on the control panel. To set the blade height: 1.
Pressure Rollers Height Adjustment The pressure rollers hold the workpiece against the conveyor table for a smooth cut. Tools Needed Qty Hex Wrench 5mm ............................................. 1 Wrench/Socket 17mm . ..................................... 2 Wrench 35mm . ................................................. 1 Horizontal Adjustment Bolt To adjust the pressure rollers: 1. Disconnect the resaw from power! 2.
Resawing 5. Adjust the conveyor speed with the variable speed adjustor shown in Figure 33. If the blade continually rotates the support bearing, reduce the speed of the conveyor. DO NOT cut slices thinner than ⁄4" off of the bottom of the stock. Attempting to cut thin slices off of the bottom may cause the blade to cut into the conveyor belt. 1 To perform a resawing operation: 1. Make sure the blade is installed and tensioned correctly as described in Installing the Blade on page 22. 2.
Blade Information The Model G0503 is a specialized machine that requires specialized blades. Grizzly Industrial has selected a series of blades for optimum performance on this machine. The only variables when selecting a blade are the type of cutting tooth and the number of teeth-per-inch (Tooth Pitch).
SECTION 5: ACCESSORIES H3788—G96® Gun Treatment 12 oz. Spray H3789—G96® Gun Treatment 4.5 oz. Spray This triple action gun treatment cleans, lubricates and protects all metal parts. Contains solvents that completely remove all traces of rust and corrosion and leaves no gummy residue. G2871—Boeshield ® T-9 12 oz Spray G2870—Boeshield® T-9 4 oz Spray This ozone friendly protective spray penetrates deep and really holds up against corrosive environments.
Lenox® Blades Replacement blades for the Model G0503 Horizontal Resaw Bandsaw. MODEL TYPE WIDTH H4874 Carbon 1" H4875 Carbide Tip 1" H4876 Carbide Tip 1" GAUGE 0.035" 0.035" 0.035" TPI 1.3 2-3 3-4 H4959—Coolant Dispenser Delivers a small amount of lubricant to the cutting surface to improve tool life and cutting efficiency. An absolute must for large resawing operations. Figure 41. H4959 Coolant Dispenser. Figure 39. Lenox® bandsaw blade.
P0503A17—440V Conversion Kit This kit allows the Model G0503 to run on 440V power. 440V power offers better start capacity, cooler motor operation, and increased motor life. T20501—Face Shield Crown Protector 4" T20502—Face Shield Crown Protector 7" T20503—Face Shield Window T20452—"Kirova" Anti-Reflective S. Glasses T20451—"Kirova" Clear Safety Glasses H0736—Shop Fox® Safety Glasses H7194—Bifocal Safety Glasses 1.5 H7195—Bifocal Safety Glasses 2.0 H7196—Bifocal Safety Glasses 2.
SECTION 6: MAINTENANCE Miscellaneous Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Cleaning Inside Wheel Cover To keep the bandsaw working properly, regularly open the wheel cover and vacuum any sawdust from the machine that did not make it into the dust collector. Resaw Wheels and Scrapers Use a dry rag to wipe sawdust from the wheel scrapers.
Greasing 3 Tools Needed Qty Grease Gun........................................................ 1 4 Hardware Needed Qty High Temp Bearing Grease....................... Varies Multi-Purpose Grease................................ Varies 1 2 Wipe grease fittings clean and lubricate with two pumps of high-temp bearing grease. To lubricate a greased surface; wipe the surface clean and apply a thin coating of multi-purpose grease.
Hydraulic Fluid Schedule Hydraulic System Minor Service In order for the hydraulic system to operate the conveyor properly and at the correct temperature, the hydraulic fluid level in the tank should be 2⁄3 full between the fill lines on the fluid sight window, which is located on the front of the tank (see Figure 48).
Hydraulic System Major Service To change the filter: 1. Read and understand the hydraulic safety instructions on page 11 before continuing! 2. Disconnect the resaw from the power source! A major service consists of performing a “Minor Service,” plus draining the fluid, cleaning the tank and screen, and filling the tank with new fluid. 3. Thoroughly clean the area around the filter to prevent contamination of the hydraulic fluid. 4. Remove the filter shown in Figure 49.
Wheel Scrapers To clean the tank screen: 1. Thoroughly clean the area around the tank access plate to prevent contamination of the hydraulic fluid. 2. Remove the access plate bolts shown in Figure 51. The wheel scrapers ride directly on the wheels removing dust and shavings. The constant motion of the wheels cause the scrapers to wear down. Eventually they will need to be replaced. Tools Needed Qty Wrench/Socket 13mm........................................ 1 To replace the scrapers: Figure 51.
SECTION 7: SERVICE Power Source Conduit Ground Tracking Locking Disconnect Switch Machine Always disconnect power to the machine Conduit before performing serGround vice adjustments. Failure to do this may result in serious personal injury. About Service This section is designed to help the operator with adjustments that were made at the factory and that might also need to be made during the life of the machine.
5. Move the bars to the other side of the conveyor belt and check the adjustable wheel. —If the wheels have the same angle compared to the conveyor table, go to step 8. —If the wheels have different angles, proceed to step 6. 6. Loosen the lock bolts and the jam nuts on the vertical adjusting bolts at the top of the adjusting plate shown in Figure 54. Vertical Adjustment Bolts Figure 55. Correct alignment. 9. Loosen the jam nuts on the tracking adjusting bolts and loosen the lock bolts.
Adjusting the Blade Guides Vertical Adjustment Bolts Each blade guide assembly consists of a guide block and a support wheel. Tilt Adjustment Bolt Each metal guide block has a guide slot that stabilizes the up/down movement of the blade and a support wheel to control backward movement. The guide block alignment should be checked each time a blade is installed. These instructions present a serious injury hazard if done while the machine is connected to power.
Adjusting the Support Wheel Blade Elevation Gauge The support wheel is positioned behind the blade to brace it from pushing backwards during a cut. Check the support wheel spacing each time a new blade is installed. Tools Needed Qty Wrench/Socket 17mm........................................ 1 Calipers.............................................................. 1 Tools Needed Qty Wrench/Socket 17mm ...................................... 1 To adjust the support wheel: 1.
Adjusting Main Conveyor Table The conveyor table can be adjusted left-to-right and front-to-back to make the table parallel to the blade in both directions. This is an involved procedure that requires you to cut up a piece of test stock and make many repeat adjustments. Because of the complexity of this procedure, we will first give instructions on checking the table, so that you can be sure you need to perform the adjustment.
4. To raise the left side, loosen the lock nuts on the conveyor adjustment bolts on the left side and tighten the adjustment bolts. Do the same procedure to the right side bolts to raise the right side. 5. Tighten the lock nuts on the adjustment bolts and tighten the conveyor mounting bolts. 6. To adjust the conveyor table front to back: 1. Disconnect the resaw from the power source! 2. Place two flat bars of wood or metal under the conveyer belt as shown in Figure 62.
Tracking Conveyor The conveyor is tracking correctly when it remains centered between the roller brackets on each side of the conveyor. Adjusting the tracking is only necessary if the conveyor belt starts rubbing against the roller brackets. Tools Needed Qty Hex Wrench 8mm.............................................. 1 Wrench 17mm.................................................... 1 To set the conveyor tracking: 1.
Replacing Conveyor 6. Slide the roller brackets toward the body of the resaw to loosen the belt. To replace the conveyor belts: 7. Remove the stiff cable from the center of the seam to separate the conveyor belt. 1. Start the conveyor belt and stop it when the conveyor belt seam (see Figure 64) is accessible. 8. Remove the old conveyor belt from the conveyor table, and install the new conveyor belt in its place. 9.
V-Belt Tensioning Replacing V-Belts Adjusting the V-belts is not an exact science. Adjusting the belts too loose will decrease the performance of the machine, but adjusting the belts too tight may cause premature wear of the components attached to the belts. Replace all three V-belts at the same time to ensure uniform belt tension. To adjust the V-belt tension: 1. 1. Disconnect the resaw from power! 2. Press the center of each V-belt firmly.
Rewiring to 440V 6. Remove the wiring covers on the main and hydraulic pump motors. Converting the Model G0503 to 440V operation consists of 1) wiring the voltage transformer, 2) rewiring the main motor and the hydraulic pump motor, and 3) replacing the over-load relays with the relays included in the Model G0503 440V Conversion Kit (item #P0503909) that is sold separately. 7. Wire the main and hydraulic pump drive motors as shown on the diagrams on the inside of each motor wire cover.
G0503 WIRING T T S S R POWER SOURCE S A1 A2 6 5 T R L1 L2 L3 I-ON 5 O-OFF 13NO LC1 D40 7 T1 T2 T3 R S 9 0V 220V 440V TRANSFORMER 220V 210V 0V LC1D096 14NO 8 4 75 AMP T1 L1 L2 L3 NO NO NC A1 21NC 8 NO NC A2 T1 T2 T3 NO 22NC 0 T FOR 220V 6 9 95 20HP MAIN MOTOR GROUND 98 97 U1 V1 W1 95 96 T1 5A FUSE T 0 5A FUSE 0 96 BLACK RED WHITE 97 0 NO NO NC NC 0 NO NO NC NC 98 1 LR3D 126 5.
Maintenance Log Date Approximate Hours Of Use Model G0503 (Mfg.
126 125 127 121 128 127 120 129 109 118 124 103 123 120 122 128 122 131 132 103 121 120 130 138 103 126 139 138 128 103 139 118 120 129 140 122 109 141 133 127 119 134 128 116 132 136 114 112 137 110 109 136 117 113 107 135 118 109 108 115 111 110 107 109 101 106 108 102 103 104 104 -52- 105 Model G0503 (Mfg.
202 228 235 230 202 228 213 214 229 231 232 234 226 227 228 233 202 212 213 214 220 228 225 219 215 221 222 218 214 224 212 213 214 223 217 216 210 202 211 209 207 208 248 203 206 205 204 202 201 Model G0503 (Mfg.
302 316 317 303 309 326 309 308 318 327 319 310 320 308 321 329 328 302 303 312 309 311 308 310 304 330 303 322 307 302 306 303 310 304 309 305 303 308 323 302 303 303 303 310 302 302 304 324 325 303 303 302 302 301 302 303 -54- 304 Model G0503 (Mfg.
401 401 402 402 403 403 405 405 404 404 406 406 407 407 408 408 409 409 409 411 409 411 413 421 412 414 422 411 413 415 414 416 411 415 415 417 416 423 417 410 424 415 416 415 416 425 418 425 419 420 426 419 420 Model G0503 (Mfg.
503 505 501 502 504 506 507 508 509 514 510 507 516 507 524 508 516 511 512 513 525 515 523 512 516 526 511 510 527 518 528 519 520 522 521 529 527 516 530 531 507 523 524 534 539 522 535 536 532 517 510 526 511 527 512 528 537 533 533 512 511 510 518 519 516 538 517 520 -56- Model G0503 (Mfg.
Motor Components 601A-3 601A-1 601A 601A-2 604 603 602 604 605 603 606 607 608 609 610 617 618 612 607 619 607 611 616 613 615 607 609 607 614 606 606 612 Model G0503 (Mfg.
-58- Model G0503 (Mfg.
826 829 815 832 807 824 801 825 826 802 826 827 829 831 815 806 816 835 804 834 826 827 815 828 816 807 818 806 819 816 815 806 820 815 823 811 833 837 813 836 814 813 817 812 806 807 808 821 809 805 802 810 801 811 812 803 804 Model G0503 (Mfg.
903 901 908 905 904 904 905 905 906 910 907 904 -60- Model G0503 (Mfg.
B54 B53 B56 B55 B52 B57 B51 B58 B59 B50 B66 B64 B62 B65 B67 B63 B64 B49 B68-1 B60 B61 B68 FLT B69 B48 B72 B73 B47 B70 B71 B68-3 B68-2 B71-1 B71-2 B68-4 B71-3 B71-4 Model G0503 (Mfg.
A02 A01 I-ON A03 L1 L2 L3 A04 21NC O-OFF LC1 D50 13NO L1 L2 L3 NO NO A1 NC LC1D096 14NO 75 AMP T1 T2 T3 NO 22NC NC T1 T2 T3 A2 NO A01-1 A06 LR3D 126 5.5-8A LR3 D33 48-65A NO NO NC NC 98 NO NO NC NC 98 97 95 97 95 96 96 A16 A07 A15 A14 � -62- � � 0 1 4 5 7 8 Model G0503 (Mfg.
14 A10 A09 A08 13 14 13 MOTOR/START PUMP/START X2 X1 POWER ON X2 X1 7 22 21 22 MOTOR/STOP A11 Model G0503 (Mfg.
REF 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 -64- PART # P0503101 PSB11M PLW04M PSS16M P0503105 P0503106 P1066079 PSB36M PLW05M PW06M P0503111 P0503112 P0503113 PW06M PN02M P0503116 PB01M PLW06M P0503119 PSB64M P0503121 PSB31M P0503123 P0503124 P0503125 P0503126 P0503127 P0503128 PSB92M P0503130 P0503131 P0503132 P0503133 P0503134 PK33M P0503136 P0503137 PB09M PW01M P0503140 DESCRIPTION
REF 304 305 306 307 308 309 310 311 312 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 PART # P0503304 P0503305 PFH02M P0503307 P0503308 PCB22M PN01M PN09M PW06M P0503316 P0503317 P0503318 PN03M P0503320 P0503321 P0503322 P0503323 P0503324 P0503325 P0503326 P0503327 P0503328 P0503329 P0503330 P0503401 P6200 PR35M P0503404 PFH12M P0503406 P0503407 P0503408 P0503409 P0503410 PB07M P0503412 PW01M PLW04M PN02M PB32M DESCRIPTION LOWER
REF 531 532 533 534 535 536 537 538 539 601A 601A-1 601A-2 601A-3 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 701 702 703 704 705 706 707 708 709 -66- PART # P0503531 PLW04M PSB31M P0503534 PSB14M P0503536 P0503537 P0503538 PB34M P0503601A P0503601A-1 P0503601A-2 P0503601A-3 P0503602 PN09M PW06M P0503605 PB09M PW01M P0503608 PLW06M PN02M P0503611 PN03M P0503613 PB32M P0503615 PVB51 P0503617 P0503618 PB07M P0503701 PN02M PW04M PCB24M P0503705 PSB64M PLW06M P0503708 PB102M DESCR
REF 824 825 826 827 828 829 831 832 833 834 835 836 837 901 903 904 905 906 907 908 910 A01 A01-1 A02A A03 A04 A06 A07 A08 A09 A10 A11 A12 A13 A14 A14A A15 A15A A16 A17A PART # P0503824 P0503825 PSS16M P0503827 P0503828 P0503829 P0503831 P0503832 P0503833 P05030834 P0503835 P0503836 P0503837 P0503901 P0503903 PB27M PW06M P0503906 P0503907 PN09M PLW05M P0503A01 P0503A01-1 P0503A02A P0503A03 P0503A04 P0503A06 P0503A07 P0503A08 P0503A09 P0503A10 P0503A11 P0503A12 P0503A13 P0503A14 P0503A14A P0503A15 P0503A15A
Troubleshooting SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. 1. Low voltage. 2. Open circuit in motor or loose connections. 1. Check power line for proper voltage. 2. Inspect all lead connections on motor for loose or open connections Motor will not start; fuses or circuit breakers blow. 1. Short circuit in power wires. 3. Circuit or motor overloaded 1. Inspect wiring for damaged insulation and shorted wires. 2.
Service Log Date Approximate Hours Of Use Model G0503 (Mfg.
Warranty and Returns Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance.
WARRANTY CARD Name______________________________________________________________________________________ Street______________________________________________________________________________________ City____________________________________________________State________Zip_____________ Phone Number______________________E-Mail_______________________FAX_________________ Model: G0503 12" Horizontal Resaw Bandsaw Serial #______________________ Order ___________ The following information is given on a voluntary bas
FOLD ALONG DOTTED LINE Place Stamp Here Grizzly INDUSTRIAL, inc. P.O.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777
