HP CANISTER DUST COLLECTOR MODEL G0583 INSTRUCTION MANUAL COPYRIGHT © JANUARY, 2005 BY GRIZZLY INDUSTRIAL, INC.; UPDATED SEPTEMBER, 2005. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .................................................................................................................................... 2 Contact Info ................................................................................................................................ 2 Identification ................................................
INTRODUCTION Foreword Contact Info Grizzly Industrial, Inc. is proud to offer the Model G0583 1 HP Canister Dust Collector. This machine is part of Grizzly’s growing family of fine machinery. When used according to the guidelines stated in this manual, you can expect years of trouble-free, enjoyable operation. If you have any comments or criticisms that you feel we should address in our next printing, please write to us at: We are also pleased to provide this manual with the Model G0583.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G0583 1 HP CANISTER DUST COLLECTOR Design Type ................................................................................. Single Stage Floor Model Overall Dimensions: Base ..............................................................................................................151⁄4" x 26" Height ......................................................................................
Identification 1 2 7 5 3 4 6 1. 2. 3. 4. 5. 6. 7.
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. 10. NEVER LEAVE WHEN MACHINE IS RUNNING.
Additional Safety for Canister Dust Collectors 1. MACHINE USE. Do not use this dust collector to pick up liquids and metal scrap including, but not limited to, nails and filings. Metallic debris will contact the spinning impeller and could spark. The spark could then cause a sawdust explosion or severe fire hazard. Also, do not pick up material which cannot safely pass through the impeller such as solid wood scraps. 2. KEEPING FINGERS SAFE.
SECTION 2: CIRCUIT REQUIREMENTS 110/220V Operation The Model G0583 features a single phase 110V/220V 1 HP motor, which is prewired to 110V. Amperage Draw 110V ....................................................... 9 Amps 220V .................................................... 4.5 Amps Plug and Recepticle Requirements The motor is prewired to 110V and no plug replacement is required. For 220V connection, rewire the motor as in Figure 2, and install a NEMA 6-15 plug (Figure 1).
Grounding Electrocution or a fire can result if the machine is not grounded correctly. Make sure all electrical circuits are grounded. DO NOT use the machine if it is not grounded. Extension Cords We do not recommend the use of extension cords with 220V equipment. Instead, arrange the placement of your equipment and the installed wiring to eliminate the need for extension cords. Should the situation be necessary to use an extension, make sure the cord is rated Standard Service (grade S) or better.
SECTION 3: SET UP This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations BEFORE starting the machine! Wear safety glasses during the entire set up process! The Model G0583 is a heavy machine (approximately 60 lbs. shipping weight). DO NOT overexert yourself while unpacking or moving your machine—get assistance. Items Needed For Set Up Items Needed for Setup QTY Hex Wrench 3mm...................................
Site Considerations Box 2: Main Components (Figure 4) E. F. G. H. I. J. K. L. M. N. O. Elbow 4"...................................................... 1 Base............................................................ 1 Clear Dust Storage Bag ............................. 1 Round Support ........................................... 1 Rectangle Supports .................................... 2 Swivel Casters ........................................... 2 Fixed Casters ...........................................
Hardware Recognition Chart -12- G0583 1 HP Canister Dust Collector
Base and Supports Components and Hardware Needed: QTY Base ...................................................................1 Casters ...............................................................4 Round Support ...................................................1 Rectangle Support..............................................2 Impeller/Separator ..............................................2 Handle ................................................................1 Hex Bolts 5⁄16"-18 x 1⁄2" .............
Canister Filter 3. Components and Hardware Needed: QTY Canister Filter .....................................................1 Handle ................................................................1 Metal Canister Clamp .........................................1 Narrow Foam Strip .............................................1 Install the handle onto the top of the canister and tighten the set screw against the flat of the shaft (Figure 10). Tools Needed: Hex Wrench 3mm.....................................
Collection Bag 3. Components and Hardware Needed: QTY Clear Collection Bag...........................................1 Lower Bag Clamp ...............................................1 Wide Foam Strip.................................................1 Tighten the lower bag clamp around the wide foam strip to seal and secure the lower collection bag (Figure 13). To install the collection bag: 1. Secure the wide foam strip around the outside bottom rim of the collector and trim the excess (Figure 12).
SECTION 4: COLLECTION SYSTEM General Material Selection The Model G0583 is designed to be a singlemachine dust collector. Locate the dust collector where it will not interfere with the workpiece being processed, and no more than 10' of ducting is used, otherwise the CFM will be reduced. To solve dust collection questions, Grizzly offers a guide book entitled Canister Dust Collection Basics that will help you design your system.
There are also many kinds of pure plastic flexible hose, such as non-perforated drainage type hose and dryer vent hose. Drainage type hose, while being economical, does not quite have the flexibility required for dust collection. The inside of the duct is also deeply corrugated and can increase the static pressure loss by as much as 50% over smooth wall duct. Dryer vent hose, while being completely flexible, is non-resistant to abrasion and has a tendency to collapse in a negative pressure system.
Be sure that you extend the bare copper wire down all branches of the system. Do not forget to connect the wires to each other with wire nuts when two branches meet at a “Y” or “T” connection. We also recommend wrapping the outside of all plastic ducts with bare copper wire to ground the outside of the system against static electrical build up. Wire connections at Y’s and T’s should be made with wire nuts. Ensure that the entire system is grounded.
Ducting Suggestions This dust collector is intended for single machine use and not designed to draw dust through long runs and multiple ports simultaneously. We do not recommend using ducting any longer than 10 feet. Otherwise, dust collection efficiency will be greatly reduced. However, still consider these general guidelines for efficient dust collection: 1. Machines that produce the most sawdust should have the shortest run of ducting between the dust collector and the machine.
SECTION 5: OPERATION Operation Safety Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire operations process. Failure to comply may result in serious personal injury. Always wear a respirator when operating your dust collector.
SECTION 6: MAINTENANCE Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire maintenance process. Failure to comply may result in serious personal injury.
To clean the canister filter: 1. Rotate the canister handle 360º in both direction to vibrate the pleated canister element and free trapped dust particles from the filter (Figure 17). The particles will fall into the collection bag. While the Model G0583 excels at collecting the majority of wood dust produced by your machines, it is not an air filter; therefore, we strongly recommend the supplemental aid of a shop air filter such as the Grizzly G5955 or G9956.
Troubleshooting SYMPTOM Motor will not start, or it growls on start up. POSSIBLE CAUSE 1. Power supply fuse or circuit breaker has tripped. 2. Toggle switch is broken inside. 3. Start capacitor is at fault. 4. Motor fan cover is dented, stopping the fan from being able to spin. 5. Motor is at fault. Motor runs slower than normal. 1. Poor electrical connection. 2. Low power source voltage. 3. Motor is at fault. Loud, repetitious noise, or excessive vibration coming from dust collector. 1.
G0583 Parts Breakdown ��� ��� ��� ��� ��� � ��� � ��� ��� ��� � � � �� � �� � Refer to Page 28 for Breakdown.
Canister Breakdown 33 36 35 37 50 51 31-1 52 53 54 41 43 39 40 38 42 46 52 45 50-1 53 44 37 47 48 G0583 1 HP Canister Dust Collector -25-
Parts List REF 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 -26- PART # P0583001 PC035 PSW09 PSW09-1 P0583031-4 P0583031-5 P0583031-6 PFS03 P0583031-8 P0583031-9 PK01M P0583003 PW06 PWR1012 PAW05M PSB02M P0583008 PSS17 PB19 P0583011 PS09M PB09 P0583014 P0583015 P0583016 P0583017 PW07 PN40 PB04M P0583021 P0583022 PFH25 DESCRIPTION 1 HP MOTOR S.
Accessories H2797—SHOP FOX® Remote Dust Collector Switch. This remote switch turns your dust collector on and off from anywhere in your shop up to 75 feet away, saving you trips to your collector whenever you operate a shop machine. Includes two controls with 9V batteries. Use H2797 on 110V dust collectors up to 11⁄2 HP. Use H5397 on 220V dust collectors up to 3 HP.
Notes -28- G0583 1 HP Canister Dust Collector
Notes G0583 1 HP Canister Dust Collector -29-
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email ________________________ Invoice # _________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value! Visit Our Website Today And Discover Why Grizzly® Is The Industry Leader! • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR -OR- Call Today For A FREE Full Color Catalog
