G0634

ManualsBrandsGrizzly ManualsPlanerG0633/G0634

MODEL G0633/G0634

JOINTER/PLANER

COMBINATION MACHINE

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8977

PRINTED IN TAIWAN

Summary of content (72 pages)

PAGE 1
MODEL G0633/G0634 JOINTER/PLANER COMBINATION MACHINE OWNER'S MANUAL COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED, JULY 2007 (BL) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PAGE 2
��
PAGE 3
Table of Contents INTRODUCTION ............................................... 2 Foreword ........................................................ 2 Contact Info ................................................... 2 G0633 Machine Data Sheet .......................... 3 G0634 Machine Data Sheet .......................... 5 Identification ................................................... 7 SECTION 1: SAFETY ....................................... 8 Safety Instructions for Machinery ..................
PAGE 4
INTRODUCTION Foreword Contact Info We are proud to offer the Model G0633/G0634 Jointer/Planer Combination Machine. This machine is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
PAGE 5
��
PAGE 6
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � ��
PAGE 7
��
PAGE 8
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � ��
PAGE 9
Identification F E X W A B I G C J H D K L V R S T M U N Q O P Figure 1. G0634 identification and controls. A. B. C. D. E. F. G. H. I. J. K. L. M. Outfeed Table Fence Cutterhead Guard Fence Height Knobs Quick Release Knobs Tilt Lock Fence Lock Lever Fence Adjustment Knob Infeed Table Lock Knob Infeed Handgrip Infeed Table Jointer Dust Port Planer Table G0633/G0634 Jointer/Planer Combo Machine N. O. P. Q. R. S. T. U. V. W X.
PAGE 10
��
PAGE 11
��
PAGE 12
Additional Safety Instructions for Jointers 1. 2. 3. 4. 5. JOINTER KICKBACK. "Kickback" is when the workpiece is thrown off the jointer table by the force of the cutterhead. Always use push blocks and safety glasses to reduce the likelihood of injury from “kickback.” If you do not understand what kickback is, or how it occurs, DO NOT operate this machine. CUTTERHEAD ALIGNMENT.
PAGE 13
Additional Safety Instructions for Planers 1. INSTRUCTION MANUAL. This machine presents significant safety hazards to untrained users. Read/understand this entire manual before starting the planer. 2. REACHING INSIDE PLANER. Never reach inside planer or remove covers when the planer is connected to power. 3. INFEED CLEARANCE SAFETY. The infeed roller is designed to pull material into the cutterhead.
PAGE 14
SECTION 2: CIRCUIT REQUIREMENTS 220V Operation Serious personal injury could occur if you connect the machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so. Grounding In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connected to the grounding prong on the plug; likewise, the outlet must be properly installed and grounded.
PAGE 15
SECTION 3: SET UP Set Up Safety This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire set up process! The Model G0633/G0634 is a heavy machine. DO NOT over-exert yourself while unpacking or moving your machine—get assistance.
PAGE 16
Inventory The following is a description of the main components shipped with your machine. Lay the components out to inventory them. E Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes. Common Components (Figure 3 & 3) Qty A. Jointer/Planer Assembly (Not shown) ........ 1 B. Push Blocks................................................ 2 C.
PAGE 17
Hardware Recognition Chart G0633/G0634 Jointer/Planer Combo Machine -15-
PAGE 18
The unpainted surfaces are coated with a waxy oil to prevent corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Citrus Degreaser. To clean thoroughly, some parts must be removed. For optimum performance from your machine, clean all moving parts or sliding contact surfaces. Avoid chlorine-based solvents, such as brake parts cleaner that may damage painted surfaces.
PAGE 19
Moving & Placing Base Unit The Model G0633/G0634 is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment to move the shipping crate and remove the machine from the crate. Brackets Figure 9. Front and right rear lifting hole locations. Unbolt the jointer/planer from the pallet, and use a forklift to lift the machine off the pallet and onto a suitable location as shown in Figure 8.
PAGE 20
Setting Outfeed Table Height The outfeed table height MUST be level with the knives or carbide inserts when they are at topdead-center. If the outfeed table is set too low, the workpiece will be tapered from front to back. If the outfeed table is set too high, the workpiece will hit the edge of the outfeed table during operation, increasing the chance of kickback. Cutterhead Guard To install the cutterhead guard: 1.
PAGE 21
Knife Setting Gauge To connect a dust collection hose: 1. Assemble the knife setting gauge using the knife setting gauge rod, feet and 9mm e-clips as shown in Figure 14. Fit the 4" dust hose over the jointer dust port, (see Figure 15), or over the planer dust port (see Figure 16), depending upon which operation mode is setup, and secure in place with a hose clamp. Figure 15. Dust hose attached to jointer dust port. Figure 14. Knife setting gauge assembly.
PAGE 22
Test Run Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. The test run consists of verifying the following: 1) The motor powers up and runs smoothly and without vibration and 2) the stop button safety feature works correctly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 37. �� Figure 17.
PAGE 23
Recommended Adjustments For your convenience, the adjustments listed below have been performed at the factory and no further setup is required to operate your machine. However, because of the many variables involved with shipping and storage, some of these adjustments may need to be repeated to ensure optimum cutting results. Keep this in mind as you start to use your new jointer/planer. Step-by-step instructions for these adjustments can be found in SECTION 7: SERVICE ADJUSTMENTS. 1.
PAGE 24
SECTION 4: OPERATIONS Operation Safety Basic Jointer Controls Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. This section covers the basic controls used during routine jointer operations.
PAGE 25
Table Movement: Loosen the cap screws on the infeed handgrip and outfeed table adjustment knob before moving the infeed and outfeed tables (Figure 19). Use an adjustable wrench to turn the outfeed adjustment knob. Cap Screw Cap Screw To move the fence to 45° outward, loosen the tilt lock and fence height knobs, move the fence flush against the table (see Figure 21), and tighten the height knobs and tilt lock. Verify the angle with a 45° square.
PAGE 26
Jointer-Planer Conversion Basic Planer Controls This section covers the basic controls used during routine planer operations. See Page 22 for a description of START/STOP/ EMERGENCY OFF buttons. Table Height Handwheel: To move the planer table, rotate the table height handwheel (Figure 22). Table Lock Lever: Turn the lever clockwise to prevent the table moving during planer operations; loosen to move the table handwheel. The Model G0633/G0634 is ready for jointer operations after it is setup.
PAGE 27
5. Turn the table lock lever (Figure 24) clockwise, pull it out, and turn the table up. The table will lock into place when raised to its highest position as shown in Figure 25. 8. Connect the dust hose to the planer dust port. 9. Flip the change lever (Figure 22) up. To change the machine for jointer operations: Table Lock Lever 1. Lower the planer table to below the 4" mark on the table height scale. 2. Reverse Steps 2-9 in the previous subsection.
PAGE 28
Stock Inspection and Requirements �� Here are some rules to follow when choosing, jointing, and planing stock on a jointer or thickness planer: DO NOT joint or surface plane stock that contains knots. Injury to the operator or damage to the workpiece can occur if the knots become dislodged during the cutting operation. • DO NOT joint or surface plane against the grain direction. Cutting against the grain increases the likelihood of stock kickback, as well as tear-out on the workpiece.
PAGE 29
Squaring Stock 12" Min. 1" Min. 12" Min. ⁄2" Min. 1 ⁄2" Min. Squaring stock involves four steps performed in the order below: 1. Surface Plane on the Jointer—The concave face of the workpiece is surface planed flat with a jointer. 2. Surface Plane on the Thickness Planer— The opposite face of the workpiece is surface planed flat with a thickness planer. 1" Min. 1 Figure 30. Minimum dimensions for edge jointing and surface planing (jointer).
PAGE 30
Surface Planing To surface plane on the jointer: 1. The purpose of surface planing on the jointer is to make one flat face on a piece of stock (see Figures 32 & 33) to prepare it for surface planing on the thickness planer. Read and understand SECTION 1: SAFETY, beginning on Page 8. 2. Make sure your stock has been inspected for dangerous conditions as described in the Stock Inspection & Requirements instructions, beginning on Page 26. NOTICE 3. Set the cutting depth for your operation.
PAGE 31
Edge Jointing The purpose of edge jointing is to produce a finished, flat-edged surface (see Figures 34 & 35) that is suitable for joinery or finishing. It is also a necessary step when squaring rough or warped stock. NOTICE If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation. To edge joint on the jointer: 1.
PAGE 32
Bevel Cutting The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see Figures 36 & 37). The Model G0633/G0634 has preset fence stops at 45˚ outward and 90˚. If your situation requires a different angle, the preset fence stops can be easily adjusted for your needs. NOTICE If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below.
PAGE 33
Basic Planer Operation The G0633/G0634 table moves approximately 1 ⁄16" with one turn of the handwheel. The basic steps of operating the planer are as follows: 1. Put on safety glasses. 2. Unless your workpiece is very flat, surface plane the workpiece on the jointer until it is flat—having the face flat will ensure that it sits flat on the planer table during operation. 3.
PAGE 34
SECTION 5: ACCESSORIES G1738—Rotacator™ Precision Planer Tool The Rotacator is a dial indicator on a magnetic base and is designed for quickly and accurately setting the critical tolerances needed when adjusting any planer, so that nasty surprises such as non-parallel and chattered cuts can be eliminated. A great setup tool for other machines! Accurate to 0.001". Indicator rotates 360˚. Figure 38. Rotacator™ Precision Planer Tool. G5562—SLIPIT® 1 Qt.
PAGE 35
G7984—Face Shield H1298—Dust Sealed Safety Glasses H1300—UV Blocking, Clear Safety Glasses H2347—Uvex® Spitfire Safety Glasses H0736—Shop Fox® Safety Glasses Safety Glasses are essential to every shop. If you already have a pair, buy extras for visitors or employees. You can't be too careful when it comes to shop safety! H1300 H7319—Carbide Inserts (10 Pack) These indexable carbide inserts can be rotated to provide four factory sharp edges before replacement. H1298 G7984 Figure 44. H7319 Carbide Inserts.
PAGE 36
SECTION 6: MAINTENANCE V-Belts Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. V-belt removal and replacement involves removing the V-belts, rolling them off of the pulleys, replacing them with new belts, then retensioning them. Schedule Always replace V-belts as a set, or belt tension may not be even among the belts and may cause premature belt failure.
PAGE 37
4. Using a 14mm wrench, loosen the four adjustment nuts and raise the motor (see Figure 47) to remove V-belt tension. It may help to use a 2x4 to lift the motor. 8. Replace the motor access cover, fence bracket, and fence. Lubrication Since all bearings are sealed and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them. Adjustment Nuts Proper lubrication of other jointer/planer components is essential for long life and trouble-free operation.
PAGE 38
Lead Screw: The lead screw should be lubricated with multi-purpose grease once a month. See Figure 50 and Parts Beakdown, P0633411, Page 61 for location. Remove the left side access panel for ingress. Fence: Lubricate with multi-purpose grease when needed in the locations shown in Figure 51. Lead Screw Planer Column Figure 51. Fence lubrication locations. Figure 50. Planer column and lead screw. Planer Column: Clean with solvent, wipe dry, and relubricate with multi-purpose grease when needed.
PAGE 39
SECTION 7: SERVICE Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Motor will not start 1. Emergency off button depressed. or fuses or circuit 2. Short circuit in line cord or plug. breakers blow. 1.
PAGE 40
Cutting (Jointer and Planer) Symptom Possible Cause Possible Solution Excessive snipe 1. Outfeed table is set too low. 1. Align outfeed table with cutterhead knife at top dead (gouge in the end center (Page 18). of the board that is 2. Operator pushing down on trailing end of 2. Reduce/eliminate downward pressure on trailing end uneven with the rest of workpiece. workpiece. of the cut). 3. Workpiece is not supported as it leaves the 3. Support the workpiece as it leaves the outfeed end of the planer.
PAGE 41
Checking/Adjusting Jointer Table Parallelism The outfeed table is preset by the factory parallel with the cutterhead. However, it is critical to check this setting. If the tables are not parallel with the cutterhead or each other, then poor cutting results and kickback can occur. —If the feeler gauge(s) do not fit between the ruler and cutterhead, or if there is a gap, adjust the table height until the feeler gauge slides with slight resistance between the ruler and table.
PAGE 42
Correcting Outfeed Cutterhead Parallelism Table to This procedure involves turning the table stop bolts to raise or lower the front of the tables until they are parallel with the cutterhead. �� To correct outfeed table parallelism: 1. Loosen the lock nuts on both stop bolts shown in Figure 54 at the front of the table. Figure 55. Infeed and outfeed tables set evenly.
PAGE 43
Adjusting Jointer Table Parallelism —If the front of the infeed table is higher or lower than the outfeed table, adjust the infeed table stop bolts (see Correcting Infeed Table to Cutterhead Parallelism on Page 40). For safe and proper cutting results, the tables must be parallel to the cutterhead. Adjusting them to be parallel is a task of precision and patience, and may take up to one hour to complete.
PAGE 44
Inspecting Knives (G0633 Only) —If both outside legs of the gauge sit firmly on the cutterhead and the middle pad just touches the knife, then that knife is set correctly. (Repeat this inspection with the other knives.) Tools Needed: Qty Knife Setting Gauge .......................................... 1 Straightedge ...................................................... 1 —If the gauge does not sit firmly on the cutterhead and touch the knife edge as described, then reset that knife.
PAGE 45
—The knives are set correctly when they just touch the bottom of the straightedge in each of the straightedge positions. —If the knives do not touch the straightedge or they lift it up in any of the positions, then those knives need to be adjusted. Adjusting/Replacing Knives (G0633) Tools Needed: Qty Straightedge ...................................................... 1 Hex Wrench 3mm.............................................. 1 Wrench 8mm .....................................................
PAGE 46
Jack Screws: Using a 3mm hex wrench, find the jack screws through the access holes in the cutterhead (Figure 62) and rotate them to raise/lower the knife. When the knife is set correctly, it will barely touch the middle pad of the knife setting gauge. For now, only tighten the gib bolts enough to hold the knife in place. Repeat Steps 5–7 with the other knives. To adjust/replace the knives: 1. DISCONNECT THE JOINTER/PLANER FROM THE POWER SOURCE! 2.
PAGE 47
Replacing Carbide Inserts (G0634) Tools Needed: Qty T-Handle Wrench w/T-20 Torx Bit..................... 1 The cutterhead is equipped with 56 indexable carbide inserts. Each insert can be rotated to reveal any one of its four cutting edges. Therefore, if one cutting edge becomes dull or damaged, simply rotate it 90˚ to reveal a fresh cutting edge (Figure 64). In addition, each insert has a reference dot on one corner.
PAGE 48
Calibrating Depth Scale The depth scale on the infeed table can be calibrated or "zeroed" if it is not correct. Tools Needed Qty Straightedge ...................................................... 1 Phillips Screwdriver ........................................... 1 To calibrate the depth scale: 1. DISCONNECT THE JOINTER/PLANER FROM THE POWER SOURCE! 2. Set the outfeed table height as described in the Setting Outfeed Table Height instructions on Page 18. 3.
PAGE 49
�� Figure 69. Pulleys properly aligned. V-belts are parallel and coplaner. — If the pulleys are aligned, then no adjustments are necessary. Setting Fence Stops The fence stops simplify the task of adjusting the fence to 45˚ and 90˚. Tools Needed Qty 45° Square ........................................................ 1 90° Square ........................................................ 1 Sliding Bevel......................................
PAGE 50
To set the 45° fence stop: 1. Loosen the fence tilt lock, and position the fence against the 45° stop bolt. 2. Loosen the lock nut on the 45˚ fence stop bolt (Figure 71). 45° Stop Bolt Adjusting Table Lock Levers The table lock levers can be adjusted if they do not lock. Tools Needed Qty Wrench 14 mm .................................................. 1 To adjust the table lock levers: Lock Nut Figure 71. Adjusting fence 45˚ outward. 3.
PAGE 51
Adjusting Gibs 3. The function of the table gibs is to eliminate excessive play in the table movement. The gibs also control how easy it is to move the tables. Repeat Steps 1-2 with the outfeed table gib control (Figure 74). Gib Nut Gib Set Screw Tools Needed Qty Adjustable Wrench ........................................... 1 Hex Wrench 8mm.............................................. 1 To adjust the table gibs: 1.
PAGE 52
Planer Table Parallelism �� Maximum Allowable Tolerances: Cutterhead/Table Side-to-Side .................. 0.002" Head Casting/Table Front/Back ................ 0.020" �� Tools Needed: Qty Rotacator ........................................................... 1 Wrench 12mm ................................................... 1 Hex Wrench 4mm.............................................. 1 Hex Wrench 8mm..............................................
PAGE 53
3. Cap Screw Tools Needed: Qty Hex Wrench 6mm .............................................. 1 Set Screw Lock Nut Cylinder Liner Figure 77. Adjusting table parallelism. —If the table is not parallel to the cutterhead side-to-side (Figure 75), loosen the two lock nuts on the right or left side of the cylinder liner. Adjust the set screws to raise or lower the table so it is parallel to the cutterhead.
PAGE 54
2. Adjust the tension screws counterclockwise so that they are five to seven turns below the top of the head casting. —If the workpiece slips when you feed it, turn the screws 1⁄2 to 1 turn counterclockwise to increase spring tension. —If the workpiece is abruptly grabbed when initially fed into the planer, turn the screws 1 ⁄2 to 1 turn clockwise to decrease spring tension. Anti-Kickback Fingers Anti-Kickback Fingers Figure 79. Anti-kickback fingers.
PAGE 55
Electrical Components Figure 82. Junction box and start capacitor. Figure 80. G0633/G0634 magnetic switch. Figure 83. Run capacitor. Figure 81. Emergency off switch. Figure 84. Jointer table limit switch.
PAGE 56
Wiring Diagram ��
PAGE 57
Stand Assembly Parts Breakdown �� G0633/G0634 Jointer/Planer Combo Machine �� -55-
PAGE 58
Stand Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 1-1 1-2 2 3 3-1 4 5 5-1 5-2 6 6-1 7 8 9 10 11 12 12-1 12-2 12-3 12-4 13 13-1 13-2 13-3 14 14-1 15 16 17 18 FRAME HINGE SHAFT BRACKET (RIGHT) HINGE SHAFT BRACKET (LEFT) DRIVE SHAFT COVER COVER FRAME COVER DOOR SIDE OPENING COVER HEX BOLT 5/16-18 X 1/2 FLAT WASHER 5/16 CARRIAGE BOLT 3/8-16 X 1 SPECIAL SCREW 3/8-16 X 1-1/2 FLAT WASHER 3/8 HEX NUT 3/8-16 MOTOR BRACKET PLANER SCALE RIVET REINFORCEMENT PLATE HEX BOLT 5/16-18 X 5/8 FLAT WASHER 5
PAGE 59
Table Assembly Parts Breakdown & List �� DESCRIPTION REF PART # DESCRIPTION 101 102 103 104-1 105 106 107 108 109 110 111 112 113 114 115 116 117 INFEED TABLE OUTFEED TABLE TABLE LIP JOINTER DUST PORT HINGE SHAFT A HINGE SHAFT B OUTFEED TABLE ADJ.
PAGE 60
Cutterhead & Motor Breakdown �� -58- G0633/G0634 Jointer/Planer Combo Machine
PAGE 61
Cutterhead & Motor Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 200 201 201 201-1 201-2 201-3 201-4 202 203 204 205 206 207 208 209 210 211 212 213 214 215 215-4 215-5 215-6 215-7 215-8 215-9 216 217 218 219 CUTTERHEAD BLOCK CUTTERHEAD (G0633) 12" SPIRAL CUTTERHEAD (G0634) INDEXABLE CUTTER (G0634) FLAT HD TORX T20 M6-1 X 15 (G0634) TORX T-HANDLE WRENCH 6MM (G0634) TORX BIT T-20 (G0634) KNIFE (G0633) GIB (G0633) GIB BOLT (G0633) COMPRESSION SPRING (G0633) OUTFEED ROLLER INFEED ROLLER COVER A
PAGE 62
Drive Assembly Breakdown & List �� REF PART # DESCRIPTION REF PART # DESCRIPTION 113 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 PLASTIC KNOB SPROCKET 66T SPROCKET 34T BUSHING SPROCKET 18T SPACER ARM BALL BEARING 6204-2RS TENSION SPRING BALL BEARING 608-2RS ROLLER CHAIN
PAGE 63
Planer Table Breakdown & List �� REF PART # DESCRIPTION REF PART # DESCRIPTION 401 402 403 404 405 406 407 408 408-1 408-2 409 410 411 412 413 414 415 417 418 419 PLANER TABLE COLUMN CYLINDER LINER LOCK SCREW COLLAR THICKNESS POINTER GEAR BOX BUSHING SELF-LUBRICATION BUSHING SELF-LUBRICATION BUSHING GEAR WORM SHAFT E
PAGE 64
Limit Switch Breakdown & List �� REF PART # DESCRIPTION REF PART # DESCRIPTION 501-1 501-2 501-3 502 503 504 505 506 507 SWING LEVER (F) SWING LEVER (M) LIMIT SWITCH BRACKET COMPRESSION SPRING EXTENSION SPRING SWITCH ACTIVATION ROD SWITCH ACTIVATION ROD SWITCH ACTIVATION ROD LOCK NUT 5/16-18 508 509 510 511 512 513 514 515 FLAT WASHER 5/16 HEX BOLT 5/16-18 X 1 HEX BOLT 5/16-18 X 1/2 HEX NUT 5/16-18 CAP SCREW
PAGE 65
Fence/Guard Breakdown & List �� G0633/G0634 Jointer/Planer Combo Machine �� -63-
PAGE 66
Fence/Guard List REF PART # 601 602 603 604 604-1 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 -64- DESCRIPTION P0633601 FENCE BASE P0633602 ADJUSTMENT TUBE W/RACK P0633603 TRUNNION BRACKET P0633604 TRUNNION P0633604-1 FENCE ANGLE SCALE P0633605 PIVOT STUD P0633606 SPACER P0633607 ADJUSTMENT SCREW P0633608 ADJUSTMENT ROD P0633609 FENCE P0633610 SLIDING BOLT P0633611 ECCENTRIC SHAFT PLN01 LOCK KNOB 3/8-16 P0633613 PINION SHAFT P0633614 FENCE SUPPORT P0633615
PAGE 67
Safety Labels and Cosmetic Parts 803 801 802 804 805 800 806 807 808 806 38 809 810 REF PART # DESCRIPTION REF PART # DESCRIPTION 38 800 801 802 803 804 805 GRIZZLY NAMEPLATE-SMALL READ MANUAL 2" X 3 5/16" RESPIRATOR/GLASSES LABEL MACHINE ID LABEL CUTTERHEAD GUARD WARNING LABEL EAR PROTECTION 2"X3 5/16"H DISCONNECT POWER LABEL 806 807 808 809 810 810 CHANGING OPERATIONS WARNING LABEL GRIZZLY GREEN PAINT GREY PUTTY TOUCH UP PAINT ELECTRICITY LABEL MODEL NUMBER LABEL G0633 MODEL NUMBER LABEL G0
PAGE 68
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
PAGE 69
��
PAGE 70
��
PAGE 71
PAGE 72
��