MODEL G0710/G0710P 1HP WALL HANGING DUST COLLECTOR OWNER'S Manual (For models manufactured since 11/11) 247570 Copyright © january, 2012 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape Or form without the written approval of Grizzly Industrial, inc.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Manual Accuracy............................................ 2 Contact Info.................................................... 2 Machine Description....................................... 2 Components & Terminology........................... 3 Machine Data Sheet....................................... 4 SECTION 1: SAFETY........................................ 6 Safety Instructions for Machinery...................
INTRODUCTION Manual Accuracy Contact Info LZ VgZ egdjY id d[[Zg i]^h bVcjVa l^i] ndjg cZl bVX]^cZ LZ kZ bVYZ ZkZgn Z[[dgi id WZ ZmVXi l^i] i]Z ^chigjXi^dch! heZX^[^XVi^dch! YgVl^c\h! VcY e]did\gVe]h d[ i]Z bVX]^cZ lZ jhZY l]Zc lg^i^c\ i]^h bVcjVa# =dlZkZg! hdbZi^bZh lZ hi^aa bV`Z Vc dXXVh^dcVa b^hiV`Z# LZ hiVcY WZ]^cY djg bVX]^cZh# >[ ndj ]VkZ Vcn fjZhi^dch dg cZZY ]Zae! jhZ i]Z ^c[dgbVi^dc WZadl id XdciVXi jh# 7Z[dgZ XdciVXi^c\! eaZVhZ \Zi i]Z hZg^Va cjbWZg V
Components & Terminology Wall Mounting Bracket Safety Paddle Switch Collection Bag Figure 1. Model G0710 shown. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. Model G0710/G0710P (Mfg.
Machine Data Sheet 0$&+,1( '$7$ 6+((7 Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 02'(/ * /G0710P +$1*,1* '867 &2//(&725 Product Dimensions: Weight................................................................................................................................................................ 51 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 19-1/2 x 18 x 44 in.
Bag Information Upper Bag Capacity................................................................................................................................ 2 cu. ft. No of Lower Bags............................................................................................................................................. 1 Upper Bags Total Area........................................................................................................................... 2 cu. ft. Upper Bag Diameter......
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
DISCONNECTING POWER SUPPLY. 6alVnh Y^h" XdccZXi bVX]^cZ [gdb edlZg hjeean WZ[dgZ hZg" k^X^c\! VY_jhi^c\! dg X]Vc\^c\ Xjii^c\ iddah W^ih! WaVYZh! XjiiZgh! ZiX# # BV`Z hjgZ hl^iX] ^h ^c D;; edh^i^dc WZ[dgZ gZXdccZXi^c\ id Vkd^Y Vc jcZmeZXi" ZY dg jc^ciZci^dcVa hiVgi# APPROVED OPERATION.
Additional Safety for Dust Collectors INTENDED USE. I]^h Yjhi XdaaZXidg ^h dcan ^ciZcYZY [dg XdaaZXi^c\ lddY Yjhi VcY X]^eh [gdb lddYldg`^c\ bVX]^cZh# 9D CDI jhZ i]^h Yjhi XdaaZXidg id XdaaZXi bZiVa! Y^gi! eZWWaZh! YgnlVaa! VhWZhidh! aZVY eV^ci! h^a^XV! a^fj^Yh! VZgdhdah! dg Vcn [aVbbVWaZ! XdbWjhi^WaZ! dg ]VoVgYdjh bViZg^" Vah# HAZARDOUS DUST.
SECTION 2: POWER SUPPLY Availability Circuit Information 7Z[dgZ ^chiVaa^c\ i]Z bVX]^cZ! Xdch^YZg i]Z VkV^a" VW^a^in VcY egdm^b^in d[ i]Z gZfj^gZY edlZg hjeean X^gXj^i# >[ Vc Zm^hi^c\ X^gXj^i YdZh cdi bZZi i]Z gZfj^gZbZcih [dg i]^h bVX]^cZ! V cZl X^gXj^i bjhi WZ ^chiVaaZY# Id b^c^b^oZ i]Z g^h` d[ ZaZXigdXj" i^dc! [^gZ! dg Zfj^ebZci YVbV\Z! ^chiVaaVi^dc ldg` VcY ZaZXig^XVa l^g^c\ bjhi WZ YdcZ Wn V fjVa^[^ZY ZaZXig^X^Vc ^c VXXdgYVcXZ l^i] Vaa Veea^XVWaZ XdYZh VcY hiVcYVgYh# 6 edlZg hj
Grounding Requirements I]^h bVX]^cZ BJHI WZ \gdjcYZY# >c i]Z ZkZci d[ XZgiV^c bVa[jcXi^dch dg WgZV`Ydlch! \gdjcY^c\ gZYjXZh i]Z g^h` d[ ZaZXig^X h]dX` Wn egdk^Y^c\ V eVi] d[ aZVhi gZh^hiVcXZ [dg ZaZXig^X XjggZci# For 120V operation: I]^h bVX]^cZ ^h Zfj^eeZY l^i] V edlZg XdgY i]Vi ]Vh Vc Zfj^ebZci"\gdjcY" ^c\ l^gZ VcY V \gdjcY^c\ eaj\ hZZ [daadl^c\ [^\" jgZ # I]Z eaj\ bjhi dcan WZ ^chZgiZY ^cid V bViX]" ^c\ gZXZeiVXaZ djiaZi i]Vi ^h egdeZgan ^chiVaaZY VcY \gdjcYZY ^c
Extension Cords 2. LZ Yd cdi gZXdbbZcY jh^c\ Vc ZmiZch^dc XdgY l^i] i]^h bVX]^cZ# >[ ndj bjhi jhZ Vc ZmiZch^dc XdgY! dcan jhZ ^i ^[ VWhdajiZan cZXZhhVgn VcY dcan dc V iZbedgVgn WVh^h# Open the motor junction box, then HiVgi remove 8VeVX^idg 120 Volt Motor '%%B;9 the wire nuts indicated in Figure 4.
SECTION 3: SETUP Unpacking This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! Needed for Setup The following are needed to complete the setup process, but are not included with your machine.
Inventory B I]Z [daadl^c\ ^h V YZhXg^ei^dc d[ i]Z bV^c Xdbed" cZcih h]^eeZY l^i] ndjg bVX]^cZ# AVn i]Z Xdbed" cZcih dji id ^ckZcidgn i]Zb# >[ Vcn cdc"egdeg^ZiVgn eVgih VgZ b^hh^c\ Z#\# V cji dg V lVh]Zg ! lZ l^aa \aVYan gZeaVXZ i]Zb0 dg [dg i]Z hV`Z d[ ZmeZY^ZcXn! gZeaVXZbZcih XVc WZ dWiV^cZY Vi ndjg adXVa ]VgYlVgZ hidgZ# C D F E Box 1: Qty A. Collector Body and Fan/Motor Assembly (Not Shown)................................................. 1 B. Wall Mounting Bracket...............
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine and the dust collection bag when full. Additionally, consider the weight of any dynamic loading that may occur when operating the machine. The physical environment where the machine is operated is important for safe operation and longevity of machine components.
Assembly For adequate motor cooling, the motor fan intake must not be restricted by a wall or cabinet. To assemble and mount the dust collector: 1. Fasten the motor bracket to the motor base with the four included flange bolts, and install the adhesive foam strip on the dust collector outlet port at the location shown in Figure 8. — If mounting to a wood framed wall (with or without drywall), the bracket must be mounted directly to a support board that is wide enough to span and mount onto two wall studs.
Collection System Material Selection Be sure that you extend the bare copper wire down all branches of the system. Do not forget to connect the wires to each other with wire nuts when two branches meet at a “Y” or “T” connection. You have many choices regarding dust collection ducting, but flexible hose is the most common for this size of machine.
Dust Collection Since each machine produces a different amount of sawdust, the requirements for the minimum amount of CFM to move that sawdust is unique to the machine (for example, a planer produces more sawdust than a table saw). Knowing this required CFM is important to gauging which size of duct to use. Based on the dust port size of the machine to be connected to the dust collector, Figure 14 will give you a close estimation of the CFM that is reduced because of dust port size.
Power Connection After you have completed all previous setup instructions and circuit requirements, the machine is ready to be connected to the power supply. Disconnecting Power 1. Ijgc i]Z bVX]^cZ edlZg hl^iX] OFF# 2.
Test Run Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. 4. Turn the machine OFF. 5. Remove the switch disabling key, as shown in Figure 18. The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) the safety disabling mechanism on the switch works correctly.
SECTION 4: OPERATIONS General To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. Damage to your eyes and lungs could result from using this machine without proper protective gear. Always wear safety glasses and a respirator when operating this machine. Operating your Model G0710/G0710P is simple and straightforward.
SECTION 5: ACCESSORIES Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly. G3181—Dust Collection Kit #1 Designed for a one machine hook-up, kit #1 comes complete with installation instructions and an accessories list for expanding your dust collection system in the future.
G2752—4" Rolling Floor Sweep G2753—4" Bench Dust Collection Attachment G2754—4" Floor Dust Collection Attachment These attachments are indispensable for collecting dust at machines without a port. The rolling floor sweep is also a convenient way to keep the shop floor or workbench top clean! Designed for use with 4" flexible hose (not included). G2752 H6396—Small Downdraft Table H6397—Large Downdraft Table Capture the dust produced by your portable sanders right on your benchtop. G2753 Figure 24.
H2499—Small Half-Mask Respirator H3631—Medium Half-Mask Respirator H3632—Large Half-Mask Respirator H3635—Cartridge Filter Pair P100 Wood dust has been linked to nasal cancer and severe respiratory illnesses. If you work aroundwood dust everyday, a half-mask respirator can be a lifesaver. Also compatible with safety glasses! T20501—Face Shield Crown Protector 4" T20502—Face Shield Crown Protector 7" T20503—Face Shield Window T20452—"Kirova" Anti-Reflective S.
SECTION 6: MAINTENANCE Impeller Tightening Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. DISCONNECT DUST COLLECTOR FROM POWER BEFORE ATTEMPTING THIS PROCEDURE! Periodically check the impeller to make sure it is tight on the motor shaft.
SECTION 7: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufacture date of your machine before calling.
Dust Collector Operation Symptom Possible Cause Possible Solution Dust collector does not adequately collect dust or chips; poor performance. 1. Dust collection bag is full. 2. Restriction in duct line. 1. Empty collection bag. 2. Remove dust line from dust collector inlet and unblock the restriction in the duct line. A plumbing snake may be necessary. 3. Relocate the dust collector closer to the point of suction, and rework ducting without sharp bends. Refer to Collection System, beginning on Page 16.
machine SECTION 8: WIRING I]ZhZ eV\Zh VgZ XjggZci Vi i]Z i^bZ d[ eg^ci^c\# =dlZkZg! ^c i]Z he^g^i d[ ^begdkZbZci! lZ bVn bV`Z X]Vc\" Zh id i]Z ZaZXig^XVa hnhiZbh d[ [jijgZ bVX]^cZh# 8dbeVgZ i]Z bVcj[VXijgZ YViZ d[ ndjg bVX]^cZ id i]Z dcZ hiViZY ^c i]^h bVcjVa! VcY hijYn i]^h hZXi^dc XVgZ[jaan# >[ i]ZgZ VgZ Y^[[ZgZcXZh WZilZZc ndjg bVX]^cZ VcY l]Vi ^h h]dlc ^c i]^h hZXi^dc! XVaa IZX]c^XVa Hjeedgi Vi *,% *)+".
Wiring Diagram HiVgi 8VeVX^idg '%%B;9 &'*K68 120 Volt Motor Li Gjc 8VeVX^idg (%B;9 '*%K68 Li Paddle Switch Figure 33. Start capacitor. 120 VAC 5-15 Plug
SECTION 9: PARTS G0710 Main Breakdown ((K' ( (' ) '% * (& + (, , &' . () - &' (* (+ &( &, &) &% && &+ '& & &&"& &- &&"( &.
G0710P Main Breakdown ( (, ) '% (+ (& * (' + , &' (( (* . - &' (- () &( &, &) &% && &+ '& & &&"& &- &&"( &. &* &&") ' &&"* &&"' &' &&"+ REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 11-1 11-2 11-3 11-4 11-5 11-6 12 WALL MOUNTING BRACKET MOTOR BRACKET PHLP HD SCR M5-.
WARRANTY CARD CVbZ TTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT HigZZi TTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT 8^in TTTTTTTTTTTTTTTTTTTTTTT HiViZ TTTTTTTTTTTTTTTTTTTTTTTTT O^e TTTTTTTTTTTTTTTTTTTTT E]dcZ TTTTTTTTTTTTTTTTTTTT :bV^a TTTTTTTTTTTTTTTTTTTTTTTT >ckd^XZ TTTTTTTTTTTTTTTTT BdYZa TTTTTTTTTTTTTTTTTTTT DgYZg TTTTTTTTTTTTTTTTTTTTTTT HZg^Va TTTTTTTTTTTTTTTTTT The following information is given on a voluntary basis.
;DA9 6ADC< 9DII:9 A>C: EaVXZ HiVbe =ZgZ '2)::,9 ).$5342)!, ).# 0 / "/8 "%,,).
WARRANTY & RETURNS cYjhig^Va! >cX# lVggVcih ZkZgn egdYjXi ^i hZaah [dg V eZg^dY d[ 1 year id i]Z dg^\^cVa ejgX]VhZg [gdb i]Z YViZ d[ ejgX]VhZ# I]^h lVggVcin YdZh cdi Veean id YZ[ZXih YjZ Y^gZXian dg ^cY^gZXian id b^hjhZ! VWjhZ! cZ\a^\ZcXZ! VXX^YZcih! gZeV^gh dg VaiZgVi^dch dg aVX` d[ bV^ciZcVcXZ# I]^h ^h
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777
