DUST COLLECTOR MODEL G1032 INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 1997. PRINTED IN USA DISCONTINUED MACHINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE LAST CONFIGURATION OF THE MACHINE BEFORE IT WAS DISCONTINUED. MACHINE CONFIGURATIONS MAY HAVE CHANGED AS PRODUCT IMPROVEMENTS WERE INCORPORATED.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 SAFETY RULES FOR ALL TOOLS ....................................................................2 ADDITIONAL SAFETY INSTRUCTIONS FOR DUST COLLECTORS................3 2. CIRCUIT REQUIREMENTS...................................................................................... 4 G110 VOLT WIRING.................................................................
SECTION 1: SAFETY WARNING: For Your Own Safety Read Instruction Manual Before Operating Collector a) Always wear eye protection. b) Always keep guards in place and in proper operating condition. c) Keep hands away from inlet during operation. Safety Instructions For Power Tools These safety rules cannot cover every situation in a work shop. Consider your conditions when setting up or operating your dust collector. 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool. 17. DON’T OVERREACH. Keep proper footing and balance at all times. 14. DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like. 18. CHECK FOR DAMAGED PARTS.
SECTION 2: CIRCUIT REQUIREMENTS 110V Wiring Your Model G1032 Dust Collector operates ideally at 110V, single phase power. The 1 HP motor will draw roughly 8 amps at 110 volts. These loads are not excessive, but if you operate your machine on any circuit that is already close to capacity, it might blow a fuse or trip a circuit breaker. If an unusual load does not exist, and power failure still occurs, consult a qualified electrician. Otherwise, consider a dedicated circuit for your machine.
SECTION 3: GENERAL INFORMATION Grizzly Industrial, Inc. is proud to offer the Model G1032 Dust Collector. This dust collector is a part of Grizzly’s growing family of fine machinery. When used according to the guidelines set forth in this manual, you can expect years of troublefree, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. The G1032 Dust Collector is the smallest stand up model in our broad line of dust collectors.
Unpacking Piece Inventory The Model G1032 Dust Collector is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. After all the parts have been removed from the carton, you should have: Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise filing a freight claim can be difficult.
Site Considerations When placing the G1032 Dust Collector in your shop, three major considerations should be addressed: working clearances, lighting and electrical, and circuit loading. 1. 2. Outlets: Electrical circuits should be dedicated or large enough to handle motor amp loads and proper lighting. Outlets should be located near each machine so power or extension cords are not obstructing high-traffic areas.
SECTION 4: ASSEMBLY Beginning Assembly Base Assembly of the G1032 is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Position the base plate upside down and locate the casters so they are within easy reach. Mount the casters to the base plate using sixteen 10 - 24 x 1⁄2" Phillips Head Screws provided. Figure 2. Caution: All die-cut metal parts have a sharp edge (called “flashing”) on them after they are formed. This is removed at the factory.
Support Column Fan / Motor There is one support column that holds the collector body & fan/motor assembly and the collector. Attach it to the base plate using the four (4) 5 ⁄16" - 18 x 3⁄4" hex bolts provided. Figure 3. The collector body includes the fan assembly, switch, and motor which are preassembled at the factory. Set the collector body on top of the upper column plate so the intake portion faces the long portion of the base.
Collector Bags The collector attaches to each support bracket. The inside of the collector is funnel shaped and directs the air around in a cyclone motion. Make sure that the inside taper (funnel) is faced downward and the collector inlet faces toward the collector body. Figure 5. Slip the collection bag over the bottom edge of the collector and pull the strap tight to secure. slip the filter bag over the top edge of the collector and pull the strap tight to secure. Figure 6. Figure 6. Figure 5.
SECTION 6: OPERATIONS Test Run Set Up Please review the safety rules if you are not sure about the risks associated with operating this machine. Turn on the power supply at the main panel if not already on. Flip toggle switch on and be ready to switch off just in case there is a problem. The dust collector should run smoothly and be free of vibration or rubbing noises. Unusual or strange sounds or symptoms must be investigated and the problem corrected before proceeding further.
Mobile Stationary For mobility, the G1032 is mounted on casters and can be moved within close proximity to one or two woodworking machines, depending on the model. You will need a flexible duct to connect each machine with a collection hood. If you wish to specifically direct air flow while the dust collector is attached to more than one machine, you will need to add a blast gate for each machine.
System Grounding Since plastic hose is abundant, relatively inexpensive, easily assembled, and airtight, it is a very popular material for conveying dust from woodworking machines to the dust collector. We recommend using flexible hose (flex-hose) to connect the woodworking machine to the dust collector. However, plastic piping, including plastic flex-hose, is an insulator, and dust particles moving against the walls of the pipe create a static electrical charge build-up.
SECTION 7: MAINTENANCE General Lubrication Periodic maintenance will ensure safe operation, long dust collector life, and low overall cost of operation. Shielded and pre-lubricated ball bearings require no lubrication on your part for the life of the bearings. Bearing life is dependent upon use. All bearings are common sizes. Routinely check the condition of the following items and repair or replace as necessary: 1. Loose mounting bolts, collector body, outlet, and support bracket mounting bolts. 2.
SECTION 8: CLOSURE The following pages contain parts diagram, parts list, general machine data and Warranty/Return information for your Model G1032 Dust Collector. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call the appropriate regional Service Department. Our trained service technicians will be glad to help you.
25 23 16 15 18 21 19 14 22 8 26 24 10 12 12-1 11 20 9 13 7 14 6 4 5 1 REF 01 02 04 05 06 07 08 09 10 11 12 13 14 -16- PART # P1032001 PS01 P1032004 PS06 P1032006 P1032007 P1032008 P1032009 P1032010 P1032011 PW07 P1032013 PFB02 2 DESCRIPTION CASTOR PHLP HD SCREW 10-24 X 1⁄2 BASE PHLP HD SCREW 10-24 X 3⁄8 INLET COVER SPECIAL CAP SCREW SETSCREW SPECIAL WASHER FAN COLLECTOR BODY FLAT WASHER 5⁄16'' BOLT FLANGE BOLT REF 15 16 18 19 20 21 22 23 24 25 26 28 29 PART # DESCRIPTION PFB03 PS
GRIZZLY MODEL G1032 DUST COLLECTOR Design Type:........................................................................................Single Stage - Upright on Casters Overall Dimensions & Specifications: Base......................................................................................................................15" x 25 5⁄8" x 1⁄2" Height ....................................................................................................................................
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name ____________________________________________________________________________________ Street ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________________________ MODEL # ______________________________Order #______________________________________________ The following information is given on a
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
