Wood Lathe MODEL G1067Z InStruction Manual Copyright © 1996 By Grizzly Industrial, Inc. Revised July, 2009 (tr) Warning: No portion of this manual may be reproduced in any shape or form without the written approval of Grizzly Industrial, inc. #5983 printed in taiwan.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
Table Of Contents SECTION 1: SAFETY........................................................................................................................2 Safety Instructions For Power Tools ..........................................................................................2 Additional Safety Instructions For The Lathe..............................................................................4 SECTION 1: INTRODUCTION ...............................................................................
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
Additional Safety Instructions For The Lathe 1. MAKE SURE ALL GUARDS are in place and that the Lathe sits on a flat, stable surface. 2. ALWAYS WEAR EYE PROTECTION or a face shield when operating the Lathe. All safety equipment should be ANSI approved. 3. USE A RESPIRATOR TO AVOID INHALING DUST. All safety equipment should be ANSI approved. 4. 5. 6. 7.
SECTION 1: INTRODUCTION Commentary Lack of familiarity with this manual could cause serious personal injury. Become familiar with the contents of this manual, including all the safety warnings. We are proud to offer the Model G1067Z. This machine is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
Unpacking Piece Inventory The Model G1067Z Wood Lathe is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. After all the parts have been removed from the carton, you should have: Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.
Site Considerations Clean Up Floor Load The Model G1067Z weighs 179 lbs. Most commercial floors are suitable for your machine. Some floors may require additional reinforcement to support the machine, the operator, and the workpiece. The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed.
Circuit Requirements Amperage Draw The Model G1067Z motor is wired to operate at 110V and will draw the following load: Circuit Breaker Requirements We recommend that the circuit you use your machine on should be dedicated. Because the machine motors are different sizes, please use the following guidelines when choosing a circuit breaker for your machine (circuit breakers rated any higher are not adequate to protect the circuit): Motor Load..............................................
Grounding Extension Cords In the event of an electrical short, grounding reduces the risk of electric shock by providing a path of least resistance to disperse electric current. This tool is equipped with a power cord that has an equipment-grounding prong. The outlet must be properly installed and grounded in accordance with all local codes and ordinances.
SECTION 2: ASSEMBLY Pre-assembly Assembly of the G1067Z is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Stand 1. Tools Required: Only a few common tools are needed to assemble this machine. Specifically, a 6" adjustable wrench, 12mm open end wrench, regular and Phillips head screwdriver and an 8mm Hex wrench. Locate all four stand legs and the two end panels.
3. Attach the long stand supports to each end assembly using the 5⁄16''-18 x 3⁄4'' carriage bolts provided (Figure 3). Installing the Switch Do not plug cord in until you are ready to test run the lathe. See Test Run section for instructions before initial run. 1. Locate the paddle switch. 2. Press the paddle switch into the cut-out on the face of the leg as shown in Figure 5. Figure 3. 4.
Note—The paddle switch is equipped with a removable safety key (Figure 7). When the lathe is not be in use, the safety key should be removed from the paddle switch and placed in a safe location. The lathe cannot be turned on when the safety key is removed from the paddle switch. Figure 8. Figure 7. Tool Rest Tailstock Thread the handle onto the tailstock handwheel and tighten down the jam nut (Figure 9). The tool rest is equipped with a cam-action clamping system to secure it to the lathe bed.
Spur Center Face Plate The G1067Z is supplied with a #2 Morse taper spur center for use when spindle turning. The spur center is used in conjunction with the tailstock live center. Install the spur center by inserting into the hole in the inboard spindle (Figure 10). The G1067Z is supplied with a 6'' face plate.The faceplate is used for bowl and plate turning. Install the face plate by threading the face plate onto the inboard spindle.
SECTION 3: ADJUSTMENTS Headstock The Model G1067Z headstock can be swiveled 180˚ as well as positioned anywhere along the bed. 1. Loosen the quick release lever by pushing it down (Figure 13). 2. Move the headstock to the desired position and re-engage the quick release lever (Figure 14). Note—The large hex nut under the headstock will require occasional adjusting to assure proper clamping pressure to the bed. Turn the hex nut in small increments to fine tune the clamping pressure. Figure 14. 1.
3. Release the set pin. Make sure the set pin has engaged in its detent by trying to rotate the headstock. 4. Now position the head stock along the bed as desired and engage the quick release lever. Never operate the lathe with the quick release lever loose. Serious personal injury may occur. Tailstock The tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. When the lever is thrown, a locking plate lifts up and secures the tool rest to the bed.
Live Center A #2 Morse taper live center is supplied with the lathe and is preinstalled from the factory (Figure 19). To remove it: 1. Turn the handwheel counter-clockwise until the tailstock barrel bottoms out in the tailstock housing. This causes the center to be forced out of the barrel. 2. Reinstall by turning the handwheel clockwise until the tailstock barrel sticks out of the tailstock housing about 1⁄2''. Insert the live center back into the tailstock barrel.
SECTION 4: OPERATIONS Test Run Tool Rest Once the assembly is complete and the adjustments are done to your satisfaction, you are ready to test the machine. Adjust the tool rest as close to the workpiece as possible without actually coming in contact with the workpiece. Test by hand turning the workpiece before turning lathe on. Ensure that the lathe chisel is fully supported by the tool rest.
Spindle Turning Before a workpiece is mounted into the lathe, the points of the installed spur center and the live center must align perfectly with one another (Figure 22). View the alignment from above the lathe and from the side. Live Center Spur Center Figure 23. 4. Once the spur center is firmly attached to the workpiece, insert the spur center (with the attached workpiece) into the headstock spindle. 5.
Outboard Turning Indexing Outboard turning is usually done when stock diameter is greater than 12''. For the size of this particular lathe and its minimum turning speed, we recommend a maximum diameter of 17'' and a maximum thickness of 2''. The headstock spindle indexes every 15˚ by inserting the indexing pin into one of the holes in the headstock. Indexing is desirable when locking the workpiece in position such as when routing flutes.
SECTION 5: MAINTENANCE General Lubrication Before performing any type of inspection or maintenance work on this lathe, be sure that the power cord is unplugged and all moving parts have come to a complete stop. Serious personal injury may occur. The G1067Z Lathe is equipped with a split pulley system which allows the speed of the lathe to be changed while its running. To assure the smooth operation of this pulley system, we recommend the main spindle and motor spindle be greased occasionally.
SECTION 6: CLOSURE The following pages contain general machine data, parts diagram, parts list and Warranty/Return information for your Model G1067Z Lathe. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call the appropriate regional Service Department. Our trained service technicians will be glad to help you.
Machine Data Sheet Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 Model G1067Z Wood Lathe Design Type ......................................................................................................Floor Model Overall Dimensions: Including Stand ....................................................................453⁄4" H x 20" W x 583⁄4" L Swing Over Bed........................................................................................................
105V2 G1067Z Wood Lathe -23-
59 46A 59 -24- G1067Z Wood Lathe
ref part # description 1 P1067Z001 BED 2 P1067Z002 HEADSTOCK 3 P6205 BEARING 6205 4 P1067Z004 INDEXING BLOCK 5 P1067Z005 MAIN SPINDLE 6 PFH08 FLAT HD SCR 10-24 x 1⁄2'' 7 pk88m KEY 4 X 4 X 74 8 P1067Z008 BRACKET 9 P6006 BEARING 6006 11 P1067Z011 LOCKING STUD 12 P1067Z012 SHIFTING ROD 13 P1067Z013 PINION SHAFT 14 P1067Z014 INDEXING PLATE 15 P1067Z015 DETENT PIN ASSEMBLY 16 P1067Z016 COLLAR 17 P1067Z017 SPEED CHANGE LEVER 18 PN05 HEX NUT 1⁄4''-20 19 P1067Z019 INDEXING PIN 20 P1067Z020 SPRING 21 P1067Z021 P
Warranty & Returns Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name ____________________________________________________________________________________ Street ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________________________ MODEL #_____________________Serial # __________________________ Order #______________________ The following information is given on
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value! Visit Our Website Today And Discover Why Grizzly® Is The Industry Leader! • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR -OR- Call Today For A FREE Full Color Catalog
