VERTICAL SPINDLE SANDER MODEL G1071 INSTRUCTION MANUAL COPYRIGHT © 1995 BY GRIZZLY INDUSTRIAL, INC. REG # TX 4 060 296 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 1999. PRINTED IN U.S.A.
-2 -
TABLE OF CONTENTS PAGE I. INTRODUCTION....................................................................................................................2 II. SAFETY RULES FOR ALL TOOLS ..................................................................................3-4 III. ELECTRICAL SERVICE REQUIREMENTS ........................................................................5 A. CIRCUIT LOADING ..................................................................................................5 B.
I. INTRODUCTION We are proud to offer the Model G1071 Oscillating Spindle Sander. The Model G1071 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of troublefree, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. The Model G1071 is intended for use in a home or small professional shop.
II. SAFETY RULES FOR ALL TOOLS The Model G1071 is inherently dangerous. Using the tool with respect and caution will lessen the possibility of mechanical damage or operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur. This machine is specifically designed for wood sanding operations. Modifications or improper use of this tool can result in damage to the machine and possible operator injury, and will void all warranties.
II. SAFETY RULES FOR ALL TOOLS - CONT’D 16. DISCONNECT TOOLS FROM POWER before servicing and when changing accessories such as sanding sleeves. 17. USE ONLY RECOMMENDED ACCESSORIES. Consult the current catalog for recommended accessories. Using improper accessories may be hazardous. 18. AVOID ACCIDENTAL STARTING. Make sure the switch is in the “OFF” position before plugging in the cord. 19. NEVER STAND OR LEAN ON TOOL.
III. ELECTRICAL SERVICE REQUIREMENTS The Model G1071 has a 1 HP motor that operates at 110V/220V. It has been pre-wired for 110V, single phase operation. Please consult the wiring diagram for information about conversion to 220V. C. GENERAL INFORMATION If converting to 220V, it will be necessary to connect a plug that matches your 220V receptacle. If you will be installing a new receptacle and plug, we recommend either of the following styles. A.
IV. SITE PLANNING V. UNPACKING A. FLOOR LOAD The sander is shipped from the factory in a carefully-packed carton. If you find the machine to be damaged after you’ve signed for delivery and the truck and driver are already gone, you will need to file a freight claim with the carrier. Save the containers and all packing materials for inspection by the carrier or its agent. Without the packing materials, filing a freight claim can be difficult.
VI. PIECE INVENTORY VII. CLEAN UP Take a quick inventory of the parts and put them aside for later assembly. The table is coated with a waxy oil to protect it from corrosion during shipment. Remove the protective coating with common paint thinner (mineral spirits) and paper towels. Since the majority of the spindle sander is pre-assembled at the factory, there aren’t a lot of items to inventory.
VIII. ASSEMBLY Assembly of the G1071 is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Review the parts diagrams and lists frequently to become familiar with all of the parts before you begin. ORDER OF ASSEMBLY A. Spindles B. Lubrication C. Table Inserts D. Sanding Sleeves E. Dust Collection TOOLS REQUIRED: Common hand tools are necessary to assemble this machine.
VIII. ASSEMBLY - CONT’D C. TABLE INSERTS The three inserts included with the Model G1071 are sized to provide free sanding spindle movement while minimizing the gap between the abrasive surface and the table top. The holes in the inserts are shaped to allow the sanding spindles to rotate freely even when the table is angled to its maximum 45° pitch. Place the insert with the smallest diameter which allows free movement of the spindle over the top of the spindle and lower it into the hole in the table top.
IX. TABLE ANGLE The Angle Adjustment Levers enable the table top to be tilted up to 45° to the front and 20° to the rear. Figure 3. Both levers must be released to allow the table to tilt. The levers are located under the table on both the left and right sides of the sander. The angle indicator shows the degree of pitch. There is a positive stop bolt (#54) that, when adjusted correctly, allows you to return the table square to the spindle with little effort.
X. SANDER SAFETY When the guidelines illustrated in this manual are followed, the Model G1071 is a safe and enjoyable tool to use, even for the novice 1. MAINTAIN A SECURE GRIP ON THE WORKPIECE. The spindle rotates at more than 1700 R.P.M. If control is lost, the workpiece could be shot from the machine at extreme speed. 2. CREATE A SAFETY ZONE AROUND THE SANDING SURFACE.
XI. OPERATIONS BEFORE STARTING YOUR SANDER FOR THE FIRST TIME, CHECK OIL LEVEL AND GREASE POINTS. See Maintenance Section for more information. Check at least monthly thereafter. Also before starting the sander, be sure you have followed all the guidelines for set up. If everything checks out, push the “ON” button and let the machine run. After a few moments, turn the machine off and use a piece of scrap wood to get a feel for the machine.
XII. MAINTENANCE Your Model G1071 Spindle Sander requires very little maintenance. Cleaning will increase the machine’s durability and efficiency by removing grime which can gum up moving parts. If you find that the machine sands less efficiently than usual, inspect the sanding sleeves and clean with a gum rubber belt cleaner (available in the Grizzly catalog) or replace them as needed.
XIII. TROUBLESHOOTING Turn switch off and disconnect from power source before troubleshooting the machine. SYMPTOM POSSIBLE CAUSE Motor will not start. 1. 2. Low or no voltage. 1. Open circuit in motor or 2. loose connections. Check power line for proper voltage. Inspect all lead connections on motor for loose or open connections. Motor will not start; 1. fuses or circuit breakers blow. 2. Short circuit in line cord 1. or plug. Short circuit in motor or 2. loose connections.
XIV. CLOSURE The following pages contain general machine data, parts diagram, parts list and Warranty/Return information for your Model G1071 Oscillating Spindle Sander. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call the appropriate regional Service Department. Our trained service technicians will be glad to help you.
MACHINE DATA SHEET Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1071 OSCILLATING SPINDLE SANDER Design Type...................................................................................................... Floor Model Overall Dimensions: Table..........................................................................................................251⁄8" x 251⁄8" Table Height ....................................................................
NOTES G1071 Oscillating Spindle Sander - 17 -
MAIN BODY PARTS DIAGRAM 84 83 1 84 113 84 2 83 83 73 118 112 82 119 72 123 3 81 66 7 85 74 4 5 71 82 6 80 82 70 75 62 89 11 65 107 108 88 81 82 81 14 82 89 80 82 4 6 5 55 92 82 A 82 85 54 69 103 104 86 8 60 87 97 9 117 61 66 67 68 89 114 25 35 10 89 23 101 82 93 20 24 23 101 76 91 90 21 89 102 17 21 12 20 89 89 22 100 121 95 98 94 97 96 15 18 13 19 18 16 99 A - 18 - G1071 Oscillating Spindle Sander
G1071 Oscillating Spindle Sander 110 49 34 77 110 34 36 32 33 110 106 79 105 110 89 115 116 89 48 78 109 30 31 110 63 28 29 110 26 110 27 106 34 105 110 53 59 111 109 34 110 52 111 58 64 34 110 51 111 57 34 110 50 111 57 SPINDLE PARTS DIAGRAM - 19 -
PARTS LIST REF# PART# DESCRIPTION REF# PART# 001 P1071001 TABLE 036 P1071036 SPINDLE 3/4" 002 P1071002 INSERT, 13/4" x 2" 048 P1071048 RUBBER GROMMET 3 DESCRIPTION 003 P1071003 INSERT, 2" x 3 /8" 049 P1071049 SPINDLE 1" 004 P1071004 BRACKET 050 P1071050 SPINDLE 11/2" 005 P1071005 TRUNNION 051 P1071051 SPINDLE 2" 006 P1071006 INNER TRUNNION 052 P1071052 SPINDLE 3" 007 P1071007 DUST HOOD 053 P1071053 SPINDLE 4" 008 P1071008 HOUSING CASTING 054 P1071054 HEX BOLT 3/8" - 16 x
PARTS LIST REF# PART# DESCRIPTION REF# PART# DESCRIPTION 082 PLW04 LOCK WASHER 3/8" 102 P1126153 DRAIN PLUG 083 PSS07 SETSCREW 1/4" - 20 x 1/2" 103 PN04 HEX NUT 5/8" - 11 084 PRP42M ROLL PIN 3 x 20mm 104 PLW06 LOCK WASHER 5/8" 085 PW02 FLAT WASHER 3/8" 105 PB19 HEX BOLT 1/4" - 20 x 1/2" 086 PN02 HEX NUT 5/16" - 18 106 PLW02 LOCK WASHER 1/4" 087 PSB38 CAP SCREW 10 - 32 x 3/8" 107 PB03 HEX BOLT 5/16" - 18 x 1" 088 PB16 HEX BOLT 3/8" - 16 x 1 1/2" 108 P1071108 5 089 PN08 HEX NU
WARRANTY AND RETURNS LIMITED WARRANTY Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name ____________________________________________________________________________________ Street ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________________________ MODEL # ______________________________Order #______________________________________________ The following information is given on a
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
