8 GAUGE BRAD NAILER MODEL G6045/G6046/G6047 INSTRUCTION MANUAL Model G6046 Model G6047 Nailer With Case Model G6045 not shown COPYRIGHT © OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools 10. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
Basic Nailer Safety In addition to the rules stated in the previous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new nailer: 1. 2. 3. 4. 5. 6. 7. 8. READ THIS ENTIRE MANUAL BEFORE OPERATING THE NAILER. ALWAYS DISCONNECT AIR FROM THE NAILER WHENEVER SERVICING OR INSTALLING NAILS. During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury. DO NOT PLACE HANDS NEAR NAIL POINT OF ENTRY.
INTRODUCTION Commentary We are proud to offer the Grizzly Model G6045/G6046/G6047 18 Gauge Brad Nailer. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below.
Compressed Air System Safety Yoke Mechanism The Models G6045 & G6046 are designed to be operated at 60-100 psi. The Model G6047 is designed to be operated at 70110 psi. Do not exceed the maximum operating pressure for your model. A safety yoke mechanism (bump fire) on the nose of the nailer acts as a secondary safety device. When the trigger is pressed, the nailer will not fire until the safety yoke mechanism is depressed. Before using your new nailer, install the included 3⁄8" quick connect fitting.
OPERATION Loading Nailer Operating Nailer To load your nailer: If you have not read the safety instructions in this manual, do not operate the nailer. 1. 2. Disconnect the air supply from the nailer! Flip the magazine latch in the direction shown in Figure 1. Before you operate your nailer, place one drop of the included oil into the quick connect fitting where the nailer connects to the air supply.
4. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. Press the trigger. If the brad nail drove into the wood far enough, continue with your intended operations. If the brad nail either went too far or not far enough, then adjust the air pressure. More air pressure will make the brad nail go deeper and less air pressure will decrease the brad nail penetration.
Clearing Jammed Nails 6. The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. The two places where a nail can get jammed are the magazine and the discharge area. Replace the driver guide cover and snap the quick release latch back into operating position. Quick Release Latch Driver Guide Cover Figure 5. Removing guide cover. To clear a jammed nail from the discharge area on the Model G6046: 1.
Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft becomes worn out. To replace a piston: Figure 7. Removing rear cap. 6. Always disconnect air from nailer whenever servicing! During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury! 1. 2. 3. 4. 5.
G6045 PART BREAKDOWN 59 43 63 61 58 54 55 39 36 33 34 35 37 62 57 40A 38 60 76 50 52 65 67 66 68 53 47 31 64 32 51 44 49 48 76 25 26 23 24 27 45 43 42 41A 46 13 14A 18 19A 21 19 22 20 71 72 3 1 2 74 75 4 5 6 7 8 9 10 11 12 8A G6045/G6046/G6047 18 Gauge Brad Nailer -10-
REF PART # DESCRIPTION REF PART # 01 02 03 04 05 06 07 08 08A 09 10 11 12 13 14A 18 19 19A 20 21 22 23 24 25 26 27 31 32 33 34 35 36 37 38 39 40A 41A P6045001 P6045002 P6045003 P6045004 P6045005 P6045006 P6045007 P6045008 P604500A P6045009 P6045010 P6045011 P6045012 P6045013 P6045014A P6045018 P6045019 P6045019A P6045020 P6045021 P6045022 P6045023 P6045024 P6045025 P6045026 P6045027 P6045031 P6045032 P6045033 P6045034 P6045035 P6045036 P6045037 P6045038 P6045039 P6045040A P6045041A CAP SCREW LOCK WAS
G6046 PART BREAKDOWN 59 43 63 61 58 54 55 39 36 33 34 35 37 62 57 40A 38 60 76 50 52 65 67 66 68 53 47 31 64 32 51 44 49 48 25 26 23 24 27 41 45 43 42 46 13 14A 18 19A 21 19 22 20 71 72 3 74 1 2 75 4 5 6 7 8 9 10 11 12 8A G6045/G6046/G6047 18 Gauge Brad Nailer -12-
REF PART # DESCRIPTION REF PART # 01 02 03 04 05 06 07 08 08A 09 10 11 12 13 14A 18 19 19A 20 21 22 23 24 25 26 27 31 32 33 34 35 36 37 38 39 40A P6046001 P6046002 P6046003 P6046004 P6046005 P6046006 P6046007 P6046008 P604600A P6046009 P6046010 P6046011 P6046012 P6046013 P6046014A P6046018 P6046019 P6046019A P6046020 P6046021 P6046022 P6046023 P6046024 P6046025 P6046026 P6046027 P6045031 P6046032 P6046033 P6046034 P6046035 P6046036 P6046037 P6046038 P6046039 P6046040A CAP SCREW LOCK WASHER CAP SEAL S
G6047 PART BREAKDOWN 59 43 63 61 58 54 55 39 36 33 34 35 37 62 57 40A 38 60 76 50 52 65 67 66 68 53 47 31 64 32 51 49 48 44 76 25 26 23 24 27 45 43 42 41A 46 13 71 72 3 1 2 74 75 4 14A 18 5 10 9 8 7 6 19A 21 19 22 20 11 12 8A G6045/G6046/G6047 18 Gauge Brad Nailer -14-
REF PART # DESCRIPTION REF PART # 01 02 03 04 05 06 07 08 08A 09 10 11 12 13 14A 18 19 19A 20 21 22 23 24 25 26 27 31 32 33 34 35 36 37 38 39 40A 41A P6047001 P6047002 P6047003 P6047004 P6047005 P6047006 P6047007 P6047008 P604700A P6047009 P6047010 P6047011 P6047012 P6047013 P6047014A P6047018 P6047019 P6047019A P6047020 P6047021 P6047022 P6047023 P6047024 P6047025 P6047026 P6047027 P6047031 P6047032 P6047033 P6047034 P6047035 P6047036 P6047037 P6047038 P6047039 P6047040A P6047041 CAP SCREW LOCK WASH
TROUBLESHOOTING PROBLEM CAUSE ACTION Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety yoke must be checked. Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Damaged bumper. 1. Tighten screws. 2. Replace O-ring. 3. Replace bumper. Air leaking between housing and cap assembly. 1. Damaged seal. 1. Replace damaged seals. Tool skips nails while discharging. 1. Air leaks. 1.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name __________________________________________________________ Street __________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #___________________________ Order #_______________________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
