OSCILLATING SPINDLE SANDER MODEL G9922 INSTRUCTION MANUAL COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA.
-B- G9922 Oscillating Spindle Sander
Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR ALL TOOLS ......................................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ....................................................................................................5 FUSING ....................................................................................................................5 EXTENSION CORDS .........
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
Additional Safety Instructions For Sanders 1. BE AWARE OF SPINDLE rotation when sanding. 2. KEEP FINGERTIPS AWAY from the moving spindle. Serious injury could result if skin contacts abrasives or moving parts. 6. IF THERE IS ANY doubt as to the stability or integrity of the material to be sanded, don’t sand it. 7. DO NOT OPERATE SANDER with a damaged or badly worn sanding sleeve. 3. NEVER USE EXCESSIVE FORCE when sanding.
SECTION 2: CIRCUIT REQUIREMENTS 110V Operation Grounding The Model G9922 is wired for 110/120V, single phase operation only. The 1⁄2 HP motor will safely draw 4.5 amps at 110V. If you operate this sander on any circuit that is already close to its capacity, it might blow a fuse or trip a circuit breaker. However, if an unusual load does not exist and a power failure still occurs, contact a qualified electrician or our service department.
SECTION 3: INTRODUCTION Commentary We are proud to offer the Grizzly Model G9922 Oscillating Spindle Sander. The Model G9922 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. The Model G9922 is a stationary sander that is capable of a wide variety of operations.
Unpacking Parts Inventory This Oscillating Spindle Sander is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier. Save the containers and all packing materials for possible inspection by the carrier or its agent. Without the packing materials, filing a freight claim can be difficult.
Clean Up Unpainted machine surfaces may be coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or Grizzly’s G7895 citrus-based degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usage instructions on the product you choose for clean up.
SECTION 4: ASSEMBLY Overview Most of your G9922 Oscillating Spindle Sander has been assembled at the factory. The few pieces that remain should go together quickly and easily. Only a few common tools are required to assemble your oscillating spindle sander. 12 x 14mm and 17 x 19mm double-end wrenches, as well as an 8mm Allen® wrench are provided with the machine.
SECTION 5: Operations Test-Run General Sanding Before you put your oscillating spindle sander into use, give it a quick inspection. Before inspecting, ensure that the machine is switched off and disconnected from its power source. For general wood sanding, position and secure table, turn the machine on and place workpiece on table. While securely holding workpiece, slowly feed against the spindle and maintain constant pressure against the table. Use caution when sanding end-grain. 1.
SECTION 6: MAINTENANCE General Sanding Sleeves Make a habit of inspecting your sander each time you use it. Check for the following conditions and repair or replace when necessary. The spindle accepts 2" x 51⁄2" sanding sleeves. For spindle sanding, we recommend a 100 grit (medium) material for general purpose sanding, a 60 grit (coarse) material for rough work, and a 150 grit (fine) material for finish jobs. 1. Loose mounting bolts. 2. Worn switch. 3. Worn or damaged cords and plugs. 4.
SECTION 7: CLOSURE The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G9922 Oscillating Spindle Sander. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service technicians will be glad to help you.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G9922 OSCILLATING SPINDLE SANDER Design Type .................................................................................................... Floor Model Overall Dimensions and Specifications: Table ........................................................................................................141⁄2" x 141⁄2" Floor to Table Height ..........................................
G9922 Oscillating Spindle Sander
REF 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 PART # G2902 P992202 P992203 P992204 P992205 P992206 P992207 P992208 P992209 P992210 P992211 P992212 P992213 P992214 PW02M PN06M PW03M PB10M P992219 P992220 P992221 PSB17M P992223 P992224 P992225 P992226 P992227 P992228 P992229 P992230 P992231 P992232 P992233 P992234 P992235 P992236 P992237 P992238 PSB17M PW05M PW02M P992242 P992243 P992244 P99224
TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE Motor will not start. 1. Low voltage. 1. Check power line for proper voltage. 2. Open circuit in motor or 2. Inspect all lead connections on motor for loose connections. loose or open connections. CORRECTIVE ACTION Motor will not start; 1. Short circuit in line cord 1. Inspect cord or plug for damaged insulation or plug. fuses or circuit breakand shorted wires. 2. Short circuit in motor or 2. Inspect all connections on motor for loose ers blow. loose connections.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
NOTES -18- G9922 Oscillating Spindle Sander
WARRANTY CARD Name ____________________________________________________________________________________ Street ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________________________ MODEL # G9922 Oscillating Spindle Sander Order #______________________________________________ The following information is given o
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
