8 GAUGE FINISH ANGLE NAILER MODEL H5570 INSTRUCTION MANUAL COPYRIGHT © SEPT, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear a protective hair covering to contain long hair. 12. ALWAYS USE SAFETY GLASSES. Also use a face or dust mask if cutting operation is dusty.
Basic Nailer Safety In addition to the rules stated in the previous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new nailer: 1. 2. 3. 4. 5. 6. 7. 8. READ THIS ENTIRE MANUAL BEFORE OPERATING THE NAILER. ALWAYS DISCONNECT AIR FROM THE NAILER WHENEVER SERVICING OR INSTALLING NAILS. During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury. DO NOT PLACE HANDS NEAR NAIL POINT OF ENTRY.
INTRODUCTION Commentary We are proud to offer the Grizzly Model H5570 18 Gauge Finish Angle Nailer. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. We are pleased to provide this manual with the Model H5570.
Compressed Air System Safety Yoke Mechanism The Model H5570 is designed to be operated at 70-100 psi. DO NOT exceed the maximum operating pressure for your model. A safety yoke mechanism (bump fire) on the nose of the nailer acts as a secondary safety device. When the trigger is pressed, the nailer will not fire until the safety yoke mechanism is depressed. Before using your new nailer, install the included 1⁄4" NPT male quick connect fitting on the nailer and a 1⁄4" NPT female fitting on the air hose.
OPERATION Oiling Nailer Loading Nailer Special oil has been included with your new Grizzly nailer to help maintain its useful life. Place one drop of oil in the nailer air inlet (as shown in Figure 1) before every use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replace with Grizzly Model G2820 Pneumatic Tool Oil.
Operating Nailer 3. If you have not read the safety instructions in this manual, DO NOT operate the nailer. Before you operate your nailer, place one drop of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer: 1. 2. Connect the air supply to the quick connect fitting. Test the loaded nailer for proper nail penetration.
Clearing Jammed Nails To clear a jammed nail from the discharge area on the Model H5570: 1. Disconnect the nailer from the air supply! Pull the spring loaded pusher all the way back and remove the nail stick. Flip up the quick release latch located on top of the nailer nose assembly as shown in Figure 6. Remove the driver guide cover as shown in Figure 7. The jammed nail should now be visible; remove it from the discharge area with needle nose pliers.
Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft becomes worn out. Always disconnect air from nailer whenever servicing! During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury! To replace a piston: 1. 2. 3. 4. Disconnect the nailer from the air supply! Remove all nails from the magazine cartridge.
H5570 PART BREAKDOWN -10- H5570 18 Gauge Finish Angle Nailer
REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PSB113M BTN CAP SCR M5-.8 X 11 40 PSB33M CAP SCREW M5-.8 X 12 02 PH5570002 EXHAUST COVER 41 PH5570041 DRIVER GUIDE 03 PH5570003 SEAL 43 PSB97M CAP SCREW M5-.8 X 6 04 PSB15M CAP SCREW M5-.8 X20 43-1 PLW01M LOCK WASHER 5MM 05 PSS08M SET SCREW M4-.
TROUBLESHOOTING PROBLEM CAUSE ACTION Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety yoke must be checked. Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Loose air fitting. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting. Air leaking between housing and cap assembly. 1. Damaged seal. 1. Replace damaged seals. Tool skips nails while discharging. 1.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name __________________________________________________________ Street __________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #_______________Serial#________________Order #______________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
