WET SHARPENER MODEL H6069 INSTRUCTION MANUAL COPYRIGHT © APRIL, 2004 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lum ber. Your risk from these exposures varies, depending on how often you do this type of work.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
Additional Safety Instructions For Wet Sharpeners 1. 2. 3. 4. 5. READ THIS MANUAL. This manual contains proper operating instructions for this machine. DO NOT jam the workpiece against the sharpening surface. Firmly grasp the workpiece in both hands and ease it against the sharpener using light pressure. DO NOT wear loose clothing while operating this machine. Roll up or button sleeves at the cuff. DO NOT place hands near, or in contact with, sharpening surfaces during operation.
INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model H6069 Wet Sharpener. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
FEATURES & CONTROLS The set up and operation instructions will be easier to understand if you are familiar with the basic features of the Model H6069 Wet Sharpener. Match up the feature list below with the letters in Figure 1 to identify the wet sander feature locations. A C B D E Figure 1. Model H6069 features and controls. A. B. C. D. E.
OPERATIONS Filling Reservoir To fill the water reservoir: 1. DISCONNECT FROM THE POWER SOURCE. 2. Loosen the tool rest adjustment lock handles and move the tool rest away from the sharpening stone. 3. Fill the water reservoir. See Figure 2 Fill Here Reduce the risk of electrocution by keeping all connections dry and off the ground. DO NOT touch plugs with wet hands. Failure to follow these warning could result in serious injury. Figure 2. Tool rest moved away from sharpening wheel.
Tool Rest Sharpening Equipped with an adjustable tool rest, the Model H6069 enables precise control over the sharpening operation. Figure 3 shows the height and angle adjustment lock handles for the tool rest. The Model H6069 Wet Sharpener, if properly used, will help you maintain the quality and life of your tools by keeping them sharp.
MAINTENANCE Reservoir Rinsing With use, the water reservoir will begin to fill with ground material from the objects being sharpened and wheel particles removed during the sharpening process. Keep the water reservoir clean and free of residue build up. To rinse the water reservoir: 1. UNPLUG THE SHARPENER FROM THE POWER SOURCE. 2. Tilt the sharpener to drain any water in the reservoir through the drain trough on the back of the sharpener. 3. Move the tool rest away from the grinding wheel. 4.
NOTES Model H6069 Wet Sharpener -9-
H6069 Wet Sharpener Parts Breakdown 3 16 10 11 9 2 4 13 1 17 19 18 12 37 17 20 42 8 49 14 48 47 41 25 5 6 7 15 43 39 40 12 21 35 22 24 36 26 34 38 23 12 28 32 45 27 31 44 29 24 30 33 REF 1 2 3 4 5 6 7 8 9 10 11 -10- PART # PH6069001 PCB14 PH6069003 PH6069004 PH6069005 PH6069006 PH6069007 PRP61M PH6069009 PR16 PH6069011 DESCRIPTION UPPER HOUSING CARRIAGE BOLT #10-32 X 3/8" LEFT SUPPORT RIGHT SUPPORT PLASTIC WASHER 3/16" LOCK HANDLE NUT 3/16-32 LOCK HANDLE LEVER ROLL PIN
Model H6069 REF 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 47 48 49 PART # PHTEK29 PH6069013 PH6069014 PH6069015 PS86M PW03M PH6069018 PH6069019 PLN03M PH6069021 PC006 PH6069023 PHTEK6M PH6069025 PH6069026 PH6069027 PH6069028 PH6069029 PS25M PH6069031 P6200 PH6069033 PH6069034 PB97M PW05M PH6069037 PH6069038 PS17M PTLW11M PH6069041 PH6069042 PH6069043 PH6069044 PH6069045 PH6069047 PH6069048 PH6069049 Model H6069 Wet Sharpener DESCRIPTION TAP SCRE
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _________________________________________________________ Street _________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________Serial # ________ 1. How did you learn about us? ___Advertisement ___Friend ___Catalog ___Card Deck ___World Wide Web ___Other__________________________ 2.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
