MODEL H6141 AIR PALM NAILER OWNER'S MANUAL COPYRIGHT © DECEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Pneumatic Tools 8. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. 15. DISCONNECT TOOLS before servicing, changing accessories, or moving to another location. 9. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 16. USE THE RECOMMENDED ACCESSORIES. Consult owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury. 10. WEAR PROPER APPAREL.
Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source. Only use filtered, lubricated, and regulated compressed air. 3. 4.
INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model H6141 Air Palm Nailer. This model is part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
SET UP Unpacking Inventory Your Model H6141 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. After you open the nailer box, you should find the following. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. Model H6141 Inventory (Figure 1) A. Air Palm Nailer .......
Compressed Air System The Model H6141 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. DO NOT exceed the 120 PSI maximum operating pressure for your model. Before using your new nailer, regulate the air pressure on your air compressor to the minimum PSI for your model. An in-line filter/lubricator/regulator unit, depicted in Figure 2, can be installed and should be located as close to the nailer as possible.
OPERATIONS General Operations If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer: 1. Connect the air supply to the quick connect fitting. 2. Hold the nail firmly in place with one hand as if using a regular hammer. 3.
Replacing Pistons/ORings If you use your nailer day in and day out, replacement pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. 6. Push the ram pin towards the inside of the nailer. This will push the cylinder free of the housing. 7. Remove the piston from the cylinder by pulling it free by the ram pin. 8. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 9.
CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose piece and depth guide of the nailer. Always be sure that the nailer is dry before using it again. Special oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 4) before every use, or after 2 hours of continuous use. Do not allow dust, chips, sand, etc.
H6141 PARTS BREAKDOWN � �� � �� �� � �� � �� � �� � �� � �� � �� � �� � �� �� �� �� �� REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB15M CAP SCREW M5-.8 X 20 13 PH6141013 RAM PIN 2 PH6141002 CAP 14 PH6141014 O-RING 61.4 X 2.6 3 PH6141003 O-RING 53.5 X 2.6 15 PH6141015 BUMPER 16 X 40 X 8 4 PH6141004 RUBBER SEAL 54MM 16 PH6141016 AXLE SLEEVE 8MM 5 PH6141005 GASKET 17 PH6141017 HOUSING 6 PH6141006 O-RING 53.5 X 2.
TROUBLESHOOTING Symptom Possible Cause Possible Solution Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Loose air fitting. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting and use teflon tape. Air leaking between housing and cap assembly. 1. Damaged gasket. 1. Replace damaged gasket. Tool skips on nail head while discharging. 1. Air leaks. 1. Tighten screws and fittings. 2. Dirt in cylinder. 2. Clean cylinder and housing. 3.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _________________________ Zip _________ Phone # ____________________ Email ________________________ Invoice # _____ Model # ____________________ Order # _______________________ Serial # ______ The following information is given on a voluntary basis.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
