CORDLESS MINI GRINDER MODEL H6156 INSTRUCTION MANUAL COPYRIGHT © JULY, 2004 BY GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 2005 (TR) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lum ber. Your risk from these exposures varies, depending on how often you do this type of work.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.
Additional Safety Instructions for this Cordless Mini Grinder 1. 2. 3. 4. 5. 6. 7. 8. READ THIS MANUAL. This manual contains proper operating instructions for this machine. DO NOT jam the grinder against the workpiece. Firmly grasp the grinder and ease it against the workpiece using light pressure. DO NOT wear loose clothing while operating this machine. Roll up or button sleeves at the cuff. DO NOT place hands near, or in contact with, mini grinder during operation. GRIP THE WORKPIECE FIRMLY.
INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model H6156 Cordless Mini Grinder. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
INVENTORY The set up and operation instructions will be easier to understand if you are familiar with the components of the Model H6156 Cordless Mini Grinder. Match up the list below with the letters in Figure 1 to identify the components. B A G C D E F Figure 1. Model H6156 inventory. A. Tool Case E. Tool Assortment B. Battery Charger F. Flashlight Base C. Battery G Sanding Drum/Disk Assortment D.
OPERATIONS Charging the Battery Installing Bits The Model H6156 is not shipped fully charged. It will have to be charged for 3 hours before use. DO NOT charge longer than this or damage to the battery may occur! The Model H6156 uses bits and cutters with an 1⁄ 8" diameter shaft. See the Grizzly catalog or website for a complete listing of available bits and accessories. To charge the battery: 1. Remove the battery from the mini grinder. 2. Insert the battery into the charger as shown in Figure 2.
3. Insert the end of a bit into the collet. At least 1⁄2" of the bit shaft should be mounted into the end of the collet. 4. Rotate the collet nut while depressing the collet lock to secure the bit. Only tighten 1/3 of a turn with the collet wrench. High RPM Uses High RPM's are best for general carving, cutting, routing, and grinding. The grinder remove material quicker at faster RPM's. Low RPM Uses Low RPM's are best for grinding and cutting materials that have low melting points.
Installing the Flashlight Base Daily Maintenance The flashlight base will give you the extra light that you need in low light situations. These items should be done after each use. To install the flashlight base: 1. Wipe the motor housing and tool bits with a dry cloth or blow off dust and debris with compressed air. 2. Check for damage to bits, cords, or the housing. 1. Unplug the tool from power! 2. Remove the collet shield. 3.
NOTES Model H6156 Cordless Mini Grinder -9-
H6156 Cordless Mini Grinder Parts Breakdown 1 3 8 5 7 4 6 2 REF 1 2 3 4 5 6 7 8 -10- PART # PH6156001 PH6156002 PH6156003 PH6156004 PH6156005 PH6156006 PH6156007 PHTEK3 DESCRIPTION UPPER HOUSING LOWER HOUSING COLLET LOCK COLLET SHIELD COLLET COLLET NUT ARMATURE TAP SCREW #5 X 1/2 Model H6156 Cordless Mini Grinder
9 16 10 15 13 12 11 14 REF 9 10 11 12 13 14 15 16 PART # DESCRIPTION PH6156009 A/C ADAPTOR PH6156010 BATTERY CHARGER PH6156011 BATTERY PH6156012 MINI GRINDER PH6156013 FLASHLIGHT BASE PH6156014 TOOL ASSORTMENT BAG PH6156015 SANDING ASSORTMENT BAG PH6156016 TOOL BIT ASSORTMENT BAG Model H6156 Cordless Mini Grinder -11-
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name ________________________________________________________________ Street _________________________________________________________ City____________________State________Zip ________________________ Phone Number____________E-Mail___________________Serial # _________ Model #_______________Serial#________________Order # _____________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
