8" & 10" Grinders Owner's Manual Model H7758/H7759

ManualsBrandsGrizzly ManualsGrinderH7758

MODEL H7758/H7759

8" & 10" Grinders

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR7764 PRINTED IN CHINA

Summary of content (28 pages)

PAGE 1
MODEL H7758/H7759 8" & 10" Grinders OWNER'S MANUAL COPYRIGHT © DECEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED APRIL, 2007 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PAGE 2
��
PAGE 3
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .................................................................................................................................... 2 Contact Info ................................................................................................................................ 2 H7758 Machine Data Sheet .....................................
PAGE 4
INTRODUCTION Foreword Contact Info We are proud to offer the Model H7758/H7759 8" & 10" Bench Grinders. These machines are part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
PAGE 5
H7758 Machine Data Sheet ��
PAGE 6
H7759 Machine Data Sheet ��
PAGE 7
Identification A B C E D A. B. C. D. E.
PAGE 8
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
PAGE 9
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys. 10. NEVER LEAVE WHEN MACHINE IS RUNNING.
PAGE 10
Additional Safety Instructions for Grinders 1. EYE PROTECTION. Grinding ejects small particles at a high rate of speed. ALWAYS wear safety glasses when using this machine. 2. MOUNTING TO BENCH/STAND. An unsecured grinder may become dangerously out of control during operation. Make sure grinder is FIRMLY secured to a bench/ stand before use. 3. WHEEL SPEED RATING. Wheels operated at a faster speed than rated for may break or fly apart.
PAGE 11
SECTION 2: CIRCUIT REQUIREMENTS 110V Operation Electrocution or fire could result if this machine is not grounded correctly or if your electrical configuration does not comply with local and state codes. Ensure compliance by checking with a qualified electrician! Serious personal injury could occur if you connect the machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so. Amperage Draw Model H7758 .................
PAGE 12
SECTION 3: SET UP Set Up Safety This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire set up process! The Model H7758/H7759 is a heavy machine. DO NOT over-exert yourself while unpacking or moving your machine—get assistance.
PAGE 13
Inventory & Assembly EYE SHIELDS are the first level of protection from flying debris or sparks and MUST be installed before operating the grinder. Use the list below and Figures 1 & 2 to inventory and assemble your grinder. H7758 Box Inventory Qty A. Grinder ....................................................... 1 B. Eye Shields (DO NOT OVERTIGHTEN) .... 2 C. Support Arms ............................................. 2 D. Support Retainers ...................................... 2 E.
PAGE 14
Mounting Test Run Mount the grinder on a workbench or stand (see Page 16) that is sturdy enough to hold the weight of the machine and any downward pressure that may be applied during operation. The test run ensures that the grinder and wheels did not get damaged during shipping. The workbench should have a level surface and be heavy, or attached to the floor, so it will not move during operation. 1. Review and understand the grinder safety information on Page 6. 2.
PAGE 15
SECTION 4: OPERATIONS Operation Safety Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing and long hair away from moving machinery.
PAGE 16
Wheel Care Wheel Selection Your safety when grinding depends, on a large part, on the condition of the wheel during grinding. A wheel in poor condition presents the possibility of breaking apart during rotation and injuring the operator and possibly causing property damage. The Model H7758 only accepts Type 1 wheels with a 5⁄8" bore. The Model H7759 only accepts Type 1 wheels with a 11⁄4" bore.
PAGE 17
Wheel Inspection Before mounting a new grinding wheel, it must be inspected. Do not assume that a wheel is in sound condition just because it is new—often damage can occur in shipping, with age, or with exposure to moisture. First, do a Visual Inspection. Look for any cracks, chips, nicks or dents in the surface of the wheel. If you see any of these, DO NOT use the wheel. Second, do a Ring Test. This test will give you an indication of any internal damage that may not be obvious during a visual inspection.
PAGE 18
Accessories ALWAYS visually inspect and perform a “ring test” on a wheel before assembly. DO NOT use damaged wheels! 5. Model H7763—Heavy Duty Grinder Stand Mount the new wheel as shown in Figure 4. Always make certain there is a paper or fiber disc between the wheel flanges and the wheel itself. Tighten the nut snugly but DO NOT over-tighten. Over-tightening can crack the wheel. NEVER assemble a grinding wheel on the arbor without paper or fiber discs between the wheel and the flange.
PAGE 19
SECTION 5: SERVICE Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Motor will not start. 1. 2. Low voltage. Open circuit in motor or loose connections. 1. 2. Check power line for proper voltage.
PAGE 20
� � -18- �� H7758 Parts Breakdown H7758/H7759 8" & 10" Bench Grinders
PAGE 21
H7758 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PHLP HD SCR M5-.8 X 10 FLAT WASHER 5MM WHEEL COVER HEX NUT M16-2 (LH) WHEEL FLANGE WHEEL TYPE-1 36-GRIT 8" X 1" X 5/8" LOCK WASHER 5MM LEFT SAFE GUARD HEX NUT M5-.8 LEFT TOOL REST HEX BOLT M8-1.25 X 10 LEFT SPARK DEFLECTOR FLAT WASHER 6MM HEX BOLT M6-1 X 6 BRACKET FLAT WASHER 8MM HEX BOLT M8-1.
PAGE 22
H7759 Parts Breakdown �� -20- H7758/H7759 8" & 10" Bench Grinders
PAGE 23
H7759 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PHLP HD SCR M5-.8 X 20 FLAT WASHER 5MM RUBBER FOOT BASE PLATE HEX BOLT M8-1.25 X 25 LOCK WASHER 8MM BASE PHLP HD SCR M5-.8 X 8 SELF-LOCK SWITCH CORD CLIP FIXED PLATE PHLP HD SCR M5-.8 X 8 WIRE BUSHING POWER CORD PHLP HD SCR M4-.7 X 10 FLAT WASHER 4MM EXT TOOTH WASHER 4MM CORD CLIP OUTER WHEEL FLANGE WHEEL TYPE-1 60 GRIT 10" X 1" X 1-1/4" HEX NUT M20-2.
PAGE 24
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
PAGE 25
��
PAGE 26
��
PAGE 27
PAGE 28
��