Mixer User Manual

ManualsBrandsGrizzly ManualsMixerH8172

MODEL H8172

CEMENT MIXER

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR9030 PRINTED IN CHINA

Summary of content (24 pages)

PAGE 1
MODEL H8172 CEMENT MIXER OWNER'S MANUAL COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PAGE 2
��
PAGE 3
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .................................................................................................................................... 2 Machine Data Sheet................................................................................................................... 2 Contact Info ..........................................................
PAGE 4
INTRODUCTION Foreword Contact Info We are proud to offer the Model H8172 Cement Mixer. This machine is part of a growing Grizzly family of fine machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
PAGE 5
��
PAGE 6
��
PAGE 7
Additional Safety for Cement Mixers 1. HAZARDOUS DUST. All cement, mortar, grout, and silicate dusts are hazardous to respiratory systems. Protect yourself and any bystanders by always wearing a respirator approved to guard against these kinds of dusts. 5. ENTANGLEMENT. The spinning drum and engaging gears present an entanglement hazard. When using the cement mixer, tie back long hair, roll up long sleeves, and remove loose clothing or jewelry to reduce the risk of an entanglement injury. 2.
PAGE 8
SECTION 2: CIRCUIT REQUIREMENTS 110V Operation Serious personal injury could occur if you connect the machine to the power source before you have completed the set up process. DO NOT connect the machine to the power source until instructed to do so. Circuit Recommendations We recommend connecting your machine to a dedicated and circuit that is rated for the amperage given below.
PAGE 9
SECTION 3: SETUP Setup Safety This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Unpacking Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover the machine is damaged, please immediately call Customer Service at (570) 546-9663 for advice.
PAGE 10
Inventory After all the parts have been removed from the carton, you should have: Main Components (Figures 1 & 2) Qty A. Lower Drum ................................................ 1 B. Motor Assembly.......................................... 1 C. Tipping Wheel ............................................ 1 D. Upper Drum ................................................ 1 E. Support Leg ................................................ 1 F. Frame ......................................................... 1 G.
PAGE 11
Assembly 3. To assemble the cement mixer: 1. Insert the wheels on the axles and secure them in place with the hairpin cotter pins, as shown in Figure 3. Connect the upper and lower plunger rods together with an M6-1 x 25 hex bolt and M61 lock nut, then insert the cotter pin where shown in Figure 5. Bend each leg of the cotter pin outward so it can't fall out. �� Figure 5.
PAGE 12
5. With the help of another person, place the lower drum on the frame assembly, as shown in Figure 7. The gear guard MUST remain installed on the lower drum. If, for any reason, it is not installed in the location shown in Figure 7, then install it now. 7. Place the upper bracket over the pivot shaft, and attach the upper bracket to the frame with two M8-1.25 x 20 hex bolts on one side and two 8mm flat washers, lock washers, and hex nuts on the other side (Figure 9). Gear Guard Figure 9.
PAGE 13
9. Place the upper drum on the lower drum with the gasket between them. Align the arrows shown in Figure 11, and secure the upper and lower drum pieces together with ten M81.25 x 20 hex bolts, 8mm lock washers, and 8mm flat washers. Note: Tighten these hex bolts progressively in a criss-cross pattern for even tension all the way around the drum. 11. Slide the motor assembly onto the bearing block shaft, then secure the motor assembly to the frame (Figure 13).
PAGE 14
SECTION 4: OPERATIONS Operation Safety Operation Tips Follow the tips below when using the cement mixer: Damage to your eyes and lungs could result from using this machine without proper protective gear. Always wear safety glasses and a respirator when operating this machine. Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing and long hair away from moving machinery.
PAGE 15
SECTION 5: MAINTENANCE Cleaning Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. • Always unplug the cement mixer before cleaning. • Avoid getting water on the motor or switch while cleaning. If you do, allow the components to thoroughly dry before plugging in the motor. • The easiest way to clean the drum is by hosing it out with water.
PAGE 16
Wiring Diagram �� Figure 16. Switch wiring.
PAGE 17
Parts Breakdown �� H8172 Cement Mixer �� -15-
PAGE 18
Parts Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PH8172001 PB03M PH8172003 PFH28M PH8172005 PH8172006 PH8172007 PB09M PH8172009 PH8172010 PH8172011 PH8172012 PB10M PW01M PH8172015 PH8172016 PH8172017 PLW04M PN03M PLN03M PH8172021 PH8172022 PH8172023 PH8172024 PH8172025 PR05M PR62M PH8172028 PH8172029 PLN04M P6202 PH8172032 PH8172033 PH8172034 PH8172035 P6206 UPPER DRUM HEX BOLT M8-1.
PAGE 19
Safety Labels Breakdown �� REF PART # DESCRIPTION REF PART # DESCRIPTION 101 102 103 104 PH8172101 PH8172102 PH8172103 PH8172104 MACHINE ID LABEL SMALL DISCONNECT PWR LABEL SMALL DRUM PINCH LABEL LARGE DRUM PINCH LABEL 105 106 107 108 PH8172105 PH8172106 PH8172107 PPAINT-1 SMALL EYE/LUNG LABEL SMALL READ MANUAL LABEL MOTOR/WATER SHOCK LABEL GRIZZLY GREEN TOUCH-UP PAINT Safety labels warn about machine hazards and ways to prevent injury.
PAGE 20
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
PAGE 21
��
PAGE 22
��
PAGE 23
PAGE 24
��