MODEL H8209 14-PIECE AIR TOOL KIT INSTRUCTION MANUAL COPYRIGHT © SEPTEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
7. AVOID ENTANGLEMENTS. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry, which may get caught in moving parts, when operating this tool. Wear a protective hair covering to contain long hair. 8. USE CORRECT AIR PRESSURE. Exceeding the maximum PSI rating of this tool may cause unpredictable operation or bursting. 9. DISCONNECT AIR PRESSURE before servicing, changing accessories, or moving to another location. Never leave this tool unattended when connected to air. 10.
Inventory Case ⁄2" Impact Wrench 1 Tool Oil Bottle Blow Gun Tire Inflator ⁄2" Impact Socket Set 1 Teflon Tape Air Hose 4mm Hex Wrench Quick Connect Fittings Quick Coupler Figure 1. Model H8209 Inventory.
OPERATIONS Impact Wrench Specifications Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. Drive Size................................................1⁄2" No Load Speed..........................7000 RPM Max. Torque...................230 ft/lb (310N.m) Air Inlet.....................................................
3. Pull the trigger until the appropriate air pressure is reached. EYE INJURY HAZARD! Wear protective equipment when using these tools. 4. If the pressure in the tire is too high, push the pressure release valve to bleed the excess pressure. Pressure Gauge Impact Wrench Your new single hammer 1⁄ 2" drive impact wrench (Figure 2) will generate up to 230 ft/lbs. of torque. Release Valve Inflator Only use thick-walled impact sockets with this air tool.
AIR IMPACT WRENCH �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� � � �� �� �� � � �� � � �� � �� �� �� �� �� �� REF PART # DESCRIPTION REF PART # �� �� DESCRIPTION 1 PH8209001 HOUSING 24 PH8209024 CYLINDER 2 PH8209002 VALVE BUSHING 25 PH8209025 ROTOR 3 PH8209003 REVERSE VALVE 26 PH8209026 ROTOR BLADE 4 PH8209004 TRIGGER 27 PH8209027 REAR END PLATE 5 PRP02M 28 P6001 6 PH8209006 VALVE STEM 29 PH8209029 FRONT END PLATE
ACCESSORIES 102 101 103 104 105 107 108 106 109 111 110 REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PH8209101 TIRE INFLATOR 107 PH8209107 FEMALE CONNECT FITTING 102 PH8209102 HEX WRENCH 4MM 108 PH8209108 MALE CONNECT FITTING 103 PH8209103 SOCKET 14MM 109 PH8209109 AIR HOSE 104 PH8209104 SOCKET 17MM 110 PH8209110 QUICK COUPLER 105 PH8209105 SOCKET 19MM 111 PH8209111 TEFLON TAPE 106 PH8209106 BLOW GUN