MODEL H8216 1 ⁄4" ANGLE DIE GRINDER INSTRUCTION MANUAL COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ����������������������������������������������������������������� ����������
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
7. AVOID ENTANGLEMENTS. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry, which may get caught in moving parts, when operating this tool. Wear a protective hair covering to contain long hair. 8. USE CORRECT AIR PRESSURE. Exceeding the maximum PSI rating of this tool may cause unpredictable operation or bursting. 9. DISCONNECT AIR PRESSURE before servicing, changing accessories, or moving to another location. Never leave this tool unattended when connected to air. 10.
INTRODUCTION Foreword Specifications The specifications, details, and photographs in this manual represent the Model H8216 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Collet Size...............................................1⁄4" No Load Speed.......................20,000 RPM Air Consumption...............................3 CFM Air Inlet....................................
OPERATIONS Installing Bits The Model H8216 uses bits and cutters with a 1/4" diameter shank. See the Grizzly catalog or www.grizzly.com for a complete listing of available bits and accessories. To install a bit: 1. DISCONNECT THE GRINDER FROM THE AIR SUPPLY! Read the manual before operation. Become familiar with this tool, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. 2.
Using the Grinder Always test the tooling bit on a scrap piece of material similar to the workpiece. Trial and error is the best way to determine the ideal setup. LUNG/EAR INJURY HAZARD! Wear protective equipment when using this tool. To use the grinder: ACCIDENTAL START HAZARD! Disconnect before service or tool changes. 1. Attach the 1/4" NPT male quick connect fitting to the air inlet plug. 2. Attach the grinder to an air supply set at 90 PSI. AIR PRESSURE HAZARD! Never exceed 120 PSI 3.
H8216 PARTS LIST �� �� �� �� �� �� �� �� �� �� � �� �� � �� �� � � �� � �� �� � �� �� �� �� �� �� REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 PART # PH8216001 PH8216002 PH8216003 PH8216004 PH8216005 PH8216006 PH8216007 PRP16M PORS004 POR0004 PH8216011 PH8216012 PH8216013 PORP007 PORP011-2 PH8216016 PH8216017 PH8216018 P625 PH8216020 PH8216021 PH8216022 PH8216023 �� � �� �� �� �� � �� �� �� � �� �� �� �� �� �� �� DESCRIPTION HOUSING VALVE STEM SEAT TRIGGER TR
