MODEL T26417/T26418 OSCILLATING SPINDLE SANDER OWNER'S MANUAL (For models manufactured since 11/13) COPYRIGHT © NOVEMBER, 2013 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #DM16072 PRINTED IN CHINA V1.11.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Contact Info.................................................... 2 Manual Accuracy............................................ 2 Identification.................................................... 3 SECTION 1: SAFETY........................................ 8 Safety Instructions for Machinery................... 8 Additional Safety for Spindle Sanders.......... 10 SECTION 2: POWER SUPPLY....................... 11 Availability.....
INTRODUCTION Contact Info Manual Accuracy We stand behind our machines. If you have any questions or need help, use the information below to contact us. Before contacting, please get the serial number and manufacture date of your machine. This will help us help you faster. We are proud to provide a high-quality owner’s manual with your new machine! Grizzly Technical Support 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Email: techsupport@grizzly.
Identification Spindle Dust Port Spindle Hex Nut Drum and Sanding Sleeve Table Tilt Lock Table Backside Identification Sanding Drum Assembly Storage ON/OFF Paddle Switch with Disabling Key Table Tilt Control Table Inserts Stand (T26418 Only) Figure 1. Identification. To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model T26417/T26418 (Mfd.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL T26417 BENCHTOP OSCILLATING SANDER Product Dimensions: Weight................................................................................................................................................................ 73 lbs. Width (side-to-side) x Depth (front-to-back) x Height........................................................................... 15 x 15 x 24 in.
Construction Materials Base.............................................................................................................................................. Formed Steel Stand............................................................................................................................................. Formed Steel Table....................................................................................................................................................
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL T26418 FLOOR-MODEL OSCILLATING SANDER Product Dimensions: Weight.............................................................................................................................................................. 126 lbs. Width (side-to-side) x Depth (front-to-back) x Height........................................................ 20-1/4 x 19-5/8 x 45-1/2 in.
Spindle Sander Info Sanding Drum Diameters................................................................................................................. 3/4, 2, 3 in. Sanding Drum Length.................................................................................................................... 4-1/2, 9, 9 in. Spindle Speed................................................................................................................................... 1725 RPM Spindle Oscillation.................
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating This Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. HAZARDOUS DUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk. HEARING PROTECTION.
Additional Safety for Spindle Sanders FEED RATE. Never jam a workpiece against the sanding surface. This can cause the workpiece to kick back or damage the machine. Firmly hold the workpiece and ease it against the spindle using light pressure. Allow the machine to do the work— do not force the workpiece. AVOIDING ENTANGLEMENT. Keep loose clothing articles such as sleeves, belts, or jewelry items away from the spindle. These items could get entangled in the spindle, resulting in serious personal injury.
SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.
Grounding & Plug Requirements This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. This machine is equipped with a power cord that has an equipment-grounding wire and a grounding plug (similar to the figure below). The plug must only be inserted into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.
SECTION 3: SETUP Unpacking Needed for Setup Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover any damage, please call us immediately at (570) 546-9663 for advice. The following are needed to complete the setup process, but are not included with your machine. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.
Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. NOTICE T26418 Inventory Box 2 (Figure 4) Qty A. Oscillating Sander....................................... 1 B. Wrench Open-Ends 19-22mm..................... 2 C.
Cleanup The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Mounting T26417 to Bench Anchoring T26418 to Floor The base of this machine has mounting holes that allow it to be fastened to a workbench or other mounting surface to prevent it from moving during operation and causing accidental injury or damage. Anchoring machinery to the floor prevents tipping or shifting and reduces vibration that may occur during operation, resulting in a machine that runs slightly quieter and feels more solid.
Assembly Place the spindle assemblies and table inserts in the appropriate-sized accessory slots beneath the table (see Figure 10). A sanding drum assembly does not need to be installed until after the test run. Table Insert Holder Spindle Assembly Holder Figure 10. Table insert and spindle assembly holder. Dust Collection This machine creates substantial amounts of dust during operation. Breathing airborne dust on a regular basis can result in permanent respiratory illness.
Test Run Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components function properly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix the problem BEFORE operating the machine again. The Troubleshooting table in the SERVICE section of this manual can help. To test run machine: 1. Clear all setup tools away from machine. 2. Connect machine to power supply. 3. Turn machine ON.
SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand. Due to the generic nature of this overview, it is not intended to be an instructional guide.
Installing Sanding Drum/Sleeve To complete a typical operation, the operator does the following: 1. Examines workpiece to make sure it is suitable for sanding. 2. If necessary, tilts table to correct angle and locks it in place. 3. Install sanding drum assembly. (Refer to Installing Sanding Drum/Sleeve sub-section on this page.) 4. Selects table insert best suited to accommodate size of the sanding drum and tilt of the table. 5. Puts on safety glasses and a respirator. 6.
Changing Spindle Sanding Sleeve 1. DISCONNECT MACHINE FROM POWER! 2. Secure sanding spindle in the machine spindle or with a vice. 3. 4. Pull sanding drum and sleeve off of sanding spindle. 5. Pull sanding sleeve off of sanding drum. 6. Re-assemble new sanding sleeve and sanding drum. Remove sanding spindle hex nut and top washer (see Figure 14).
Tilting Table 2. Loosen locking ring that holds table tilt by rotating it counterclockwise (see Figure 16). To tilt the table: 1. Loosen locking lever shown in Figure 15 by rotating counterclockwise. Locking Ring Adjustment Handle Locking Lever Figure 16. Loosening locking ring. Table Angle Scale 3. Set table tilt using angle scale while rotating adjustment handle. 4. Tighten locking lever and locking ring. Figure 15. Loosening table tilt lock lever. -22- Model T26417/T26418 (Mfd.
Table Inserts Sanding To ensure the workpiece is supported during sanding operations, use the table insert that matches the corresponding drum and sleeve (see table below). It is important to keep the gap between the table insert and drum as small as possible to reduce the risk of a pinch hazard. Use the oval inserts when sanding with the table tilted. T26417 Sanding Sleeves Sanding Drums Table Inserts ⁄4" 1" 1" 1" 11⁄4" 2" 2" 21⁄4" 3 ⁄4" 3 To sand a workpiece: 1.
ACCESSORIES SECTION 5: ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. T20501—Face Shield Crown Protector 4" T20502—Face Shield Crown Protector 7" T20503—Face Shield Window T20452—"Kirova" Anti-Reflective S. Glasses T20451—"Kirova" Clear Safety Glasses H7194—Bifocal Safety Glasses 1.5 H7195—Bifocal Safety Glasses 2.
Grizzly offers a wide variety of rigid aluminum oxide sanding sleeves that are perfect for use with popular sanding drum kits. H3632—Respirator Facepiece H3635—Particulate Aerosol Cartridges, 2 pk. This lightweight elastomeric facepiece has cradle suspension, easy adjust headstraps and low profile for greater field of vision and compatibility with normal use of glasses or goggles. Purchase cartridges separately depending upon intended application. Figure 21. 3-pack of hard sanding sleeves.
SECTION 6: MAINTENANCE Lubrication To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily Check: • Loose mounting bolts. • Sanding drums and sleeves for wear or damage. • Worn or damaged wires. Any other unsafe condition.
SECTION 7: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Symptom Possible Cause Possible Solution Motor will not start; fuses or circuit breakers blow. 1. Switch disabling key removed. 2. Loose connections at motor or switch.
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
T26417 Wiring Diagram MOTOR 110V 110 VAC 5-15 Plug (Prewired) Gnd Start Capacitor 24MFD 300VAC Neutral See Figure 27 Hot Gnd Ground PADDLE SWITCH (Viewed from Behind) See Figure 26 Figure 26. T26417 switch connections. Model T26417/T26418 (Mfd. Since 11/13) Figure 27. T26417 capacitor connections.
T26418 Wiring Diagram MOTOR 110V Gnd Start Capacitor 45MFD 300VAC 110 VAC 5-15 Plug (Prewired) See Figure 29 Neutral Hot Gnd Ground PADDLE SWITCH (Viewed from Behind) See Figure 28 Figure 28. T26418 switch connection. -30- READ ELECTRICAL SAFETY ON PAGE 26! Figure 29. T26418 motor connections. Model T26417/T26418 (Mfd.
SECTION 9: PARTS T26417 Main 31 59 60 61 6 53 54 44 43 45 5 41 37 26 37 47 140 28 21 22 7 35 9 34 48 57 58 46 55 56 63 35 17 68 14 18 3 25 18 67 16 14 67 2 17 8 21 22 10 13 14 27 66 67 11 19 1 38 65 23 12 14 66 42 39 40 15 20 14 24 33 49 67 51 4 36 19 62 50 52 Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase.
T26417 Main REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 31 33 34 35 36 STAND TABLE BRACKET (RH) TABLE BRACKET (LH) GRIZZLY SAFETY PADDLE SWITCH WORK TABLE SPINDLE 10MM X 3-1/2" TILT BRACKET (LH) TILT BRACKET (RH) ADJUSTABLE HANDLE M6-1 X 10 TILT GEAR 21T TILT RACK LOCKING THUMBWHEEL TILT SHAFT FLAT WASHER 6MM FLAT WASHER 5MM HEX BOLT M6-1 X 12 HEX BOLT M8-1.25 X 16 HEX BOLT M8-1.25 X 20 HEX BOLT M6-1 X 16 HEX BOLT M5-.
T26417 Oscillator Assembly 126 129 27 128 125 101 114 107 124 131 116-1 116-2 116-5 111 108 109 137 127 138 106 112 110 112 115 116-3 116-4 116-6 125 116 120 139 132 117 104 117 107 137 111 130 124 109 118 113 135 108 131 119 103 122 122 123 130 102 121 133 134 136 REF PART # DESCRIPTION REF PART # DESCRIPTION 27 101 102 103 104 106 107 108 109 110 111 112 113 114 115 116 116-1 116-2 116-3 116-4 116-5 116-6 117 OSCILLATOR ASSEMBLY MOTOR MOUNT SPINDLE BASE QUILL OSCILLATOR
T26417 Machine Labels & Cosmetics 208 201 207 206 205 202 204 203 REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 203 204 MACHINE ID LABEL MODEL NUMBER LABEL GRIZZLY.COM LABEL ENTANGLEMENT HAZARD LABEL 205 206 207 208 READ MANUAL LABEL EYE/LUNG HAZARD LABEL GRIZZLY GREEN TOUCH-UP PAINT DISCONNECT WARNING LABEL PT26417201 PT26417202 PT26417203 PT26417204 PT26417205 PT26417206 PT26417207 PT26417208 Safety labels help reduce the risk of serious injury caused by machine hazards.
T26418 Main 54 56 4 51 23 14 36 26 44 51 22 48 12 47 35 23 17 28 58 70 71 31 1 22 23 16 13 5 24 40 19 59 25 22 41 61 62 16 63 64 6 65 2 57 67 35 42 59 14 36 17 3 21 11 15 60 53 66 22 28 55 68 69 9 10 72 32 8 33 20 27 23 22 46 23 7 16 20 24 43 49 38 52 37 37 23 30 29 18 Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase.
T26418 Main REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 TILT BRACKET (LH) TILT BRACKET (RH) ANGLE RACK WORK TABLE TABLE BRACKET (LH) TABLE BRACKET (RH) GRIZZLY SAFETY PADDLE SWITCH TILT HANDLE TILT SHAFT LOCKING THUMBWHEEL TILT GEAR 21T DUST DEFLECTOR (LOWER) DUST DEFLECTOR (UPPER) ECCENTRIC SPACER OSCILLATOR ASSEMBLY HEX BOLT M8-1.25 X 16 HEX BOLT M6-1 X 16 HEX BOLT M8-1.
T26418 Oscillator Assembly 126 129 15 128 125 101 114 107 124 131 116-1 116-2 116-5 111 108 109 116-3 116-4 116-6 137 127 138 106 112 110 112 140 115 125 116 135 120 139 132 117 104 117 107 137 111 130 124 109 118 113 108 131 119 103 122 123 122 130 102 121 133 134 136 REF PART # DESCRIPTION REF PART # DESCRIPTION 15 101 102 103 104 106 107 108 109 110 111 112 113 114 115 116 116-1 116-2 116-3 116-4 116-5 116-6 117 OSCILLATOR ASSEMBLY MOTOR MOUNT SPINDLE BASE QUILL OSCILLAT
T26418 Machine Labels & Cosmetics 201 208 207 206 202 205 203 204 REF PART # DESCRIPTION REF PART # DESCRIPTION 201 202 203 204 MACHINE ID LABEL GRIZZLY GREEN TOUCH-UP PAINT GRIZZLY.COM LABEL ENTANGLEMENT HAZARD LABEL 205 206 207 208 DISCONNECT WARNING LABEL EYE/LUNG HAZARD LABEL MODEL NUMBER LABEL READ MANUAL LABEL PT26418201 PT26418202 PT26418203 PT26418204 PT26418205 PT26418206 PT26418207 PT26418208 Safety labels help reduce the risk of serious injury caused by machine hazards.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email _________________________________________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
