MODEL G0555/G0555P ULTIMATE 14" BANDSAW OWNER'S Manual Model G0555P Model G0555 252923 Copyright © AUGUST, 2002 By Grizzly Industrial, Inc., Revised JUNE, 2011 (TSJBCR) Warning: No portion of this manual may be reproduced in any shape Or form without the written approval of Grizzly Industrial, inc.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
Table of Contents INTRODUCTION................................................ 2 Manual Accuracy............................................ 2 Contact Info.................................................... 2 Machine Description....................................... 2 Identification.................................................... 3 Machine Data Sheet....................................... 4 SECTION 1: SAFETY........................................ 6 Safety Instructions for Machinery...................
INTRODUCTION Manual Accuracy Contact Info We are proud to offer this manual with your new machine! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the machine we used when writing this manual. However, sometimes we still make an occasional mistake. We stand behind our machines. If you have any questions or need help, use the information below to contact us. Before contacting, please get the serial number and manufacture date of your machine.
Identification L A M N P B O D Q E C F R G I H J S T K Front View U Rear View Figure 1. G0555/G0555P identification. A. B. C. D. E. F. G. H. I. J. K. Upper Wheel Cover ON/OFF Switch w/Disabling Padlock Fence Blade Guard Upper Blade Guide Assembly Table Pin Miter Gauge Assembly Lower Wheel Cover Fence Lock Lever Front Table Lock Knob Stand Assembly L. Blade Tension Adjustment Knob M. Blade Tension Quick Release Lever N. Guide Post O. Guide Post Lock Knob P. Blade Tension Scale Q.
maCHiNe data SHeet © Grizzly Industrial, Inc. • Customer Service: (800) 523-4777 • Website: www.grizzly.com model G0555/G0555P ultimate 14" BaNdSaW Product Dimensions: Weight ........................................................................................................................................................................... 167 lbs. Length/Width/Height .................................................................................................................................
Blade Information Standard Blade Length..............................................................................................................................................931⁄2" Blade Length Range....................................................................................................................................... 921⁄2"–931⁄2" Blade Width Range ..........................................................................................................................................
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
DISCONNECTING POWER SUPPLY.Alwaysdisconnect machine from power supply before servicing, adjusting, or changing cutting tools (bits, blades, cutters, etc.). Make sure switch is in OFF positionbeforereconnectingtoavoidanunexpectedorunintentionalstart. APPROVED OPERATION. Untrained operators can be seriously hurt by machinery. Only allow trained or properly supervised people to use machine.
Additional Safety for Bandsaws BLADE CONDITION. Do not operate with dull, cracked or badly worn blade. Dull blades require more effort to perform the cut and increase the risk of kickback. Inspect blades for cracks and missing teeth before each use. HAND PLACEMENT. Never position fingers or hands in line with the blade. If the workpiece or your hands slip, serious personal injury could occur. WORKPIECE MATERIAL.
SECTION 2: POWER SUPPLY Availability Circuit Information Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards.
Grounding Requirements This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current. Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment-grounding wire.
Extension Cords Voltage Conversion We do not recommend using an extension cord with this machine. If you must use an extension cord, only use it if absolutely necessary and only on a temporary basis. The voltage conversion MUST be performed by a electrician or qualified service personnel. To perform the voltage conversion, install the correct plug and rewire the motor to the new voltage, according to the provided wiring diagram on Page 56.
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine! Wear safety glasses during the entire setup process! This machine and its components are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy items. The following are needed to complete the setup process, but are not included with your machine.
Hardware Recognition Chart Model G0555/G0555P (Mfg.
Inventory A The following is a description of the main components shipped with your machine. Lay the components out to inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. Shipping Inventory: (Figures 4–6) Qty A. Bandsaw Assembly......................................1 B. Upper Stand Braces.....................................2 C. Stand Top.....................
Cleanup The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.
Assembly 2. Attach the remaining stand side to the assembly, as shown in Figure 9, with (8) M6-1 x 16 hex bolts, (8) 6mm flat washers, and (8) M6-1 flange nuts. Some metal parts may have sharp edges that can cause minor injury. Please examine the edges of all metal parts BEFORE handling them and be careful WHILE handling them. To assemble the bandsaw: 1.
4. Turn the stand assembly upright and attach the top, as shown in Figure 11, with (8) M8-1.25 x 16 carriage bolts and (8) M8-1.25 flange nuts. 7. With the help of other people, lift the bandsaw assembly onto the stand and align the mounting holes. 8. Secure the bandsaw assembly to the stand with (4) M8-1.25 x 35 hex bolts, (8) 8mm flat washers, (4) 8mm lock washers, and (4) M8-1.25 hex nuts, as shown in Figure 13. x8 x4 Figure 11. Stand top attached. 5.
10. Thread the remaining M8-1.25 hex nut onto the M8-1.25 x 80 positive stop hex bolt, then thread the bolt into the trunnion so that approximately 2" protrudes above the trunnion (see Figure 15). This will allow the table to rest approximately level when it is installed during the following steps. 12.
15. Attach the front fence rail to the table with the (2) M6-1 x 20 hex bolts, (2) 6mm lock washers, and (2) 6mm flat washers (see Figure 18). 17. Thread (1) M8-1.25 hex nut onto the fence lock handle, then thread the handle into the fence and secure it in place by tightening the hex nut against the fence. Note: There is a small amount of vertical play in the rail holes. Make sure to position the rail evenly along its length before tightening the hex bolts.
Blade Center Tracking Blade tracking is affected by the tilt of the upper wheel (known as center tracking) and the alignment of both wheels (known as coplanar tracking). The wheels on this bandsaw were aligned at the factory, so center tracking is the only adjustment that needs to be performed when the saw is new (refer to the Wheel Alignment on Page 49 for detailed instructions on coplanar tracking). Note: Changes in the blade tension may change the blade tracking.
6. Dust Collection Unlock the blade tracking adjustment knob so the knob will rotate for adjustments in the next steps. Note: The blade tracking adjustment knob controls the tilt of the upper wheel which, in turn, controls the center tracking of the blade. 7. Spin the upper wheel with one hand and use the blade tracking adjustment knob with the other hand to make the blade ride in the center of the bandsaw wheel tire. 8.
Power Connection Test Run After you have completed all previous setup instructions and circuit requirements, the machine is ready to be connected to the power supply. Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. To avoid unexpected startups or property damage, use the following steps whenever connecting or disconnecting the machine.
Tensioning Blade 4. Turn the machine OFF. 5. Insert the switch disabling padlock through the green ON button, as shown in Figure 27. Padlock Shaft A properly tensioned blade is essential for making accurate cuts, extending the life of the blade, and making many other bandsaw adjustments. Note: Before you performed the Test Run, you tensioned the blade according to the blade tension scale, which is only an approximate tension.
5. Look at what the tension gauge reads and use that as a guide for tensioning that blade in the future. Note: Do not rely on this setting for long periods of time because the blade will stretch with use. Additionally, with extended use, the blade tensioning system may need to be reset for correct operation. Refer to the Resetting Blade Tensioner in the Service section on this manual. When using a 3 ⁄4" blade, the blade tensioning system may need to be reset for correct operation.
6. Tighten the guide assembly lock bolt to secure the setting. 7. Loosen the thumbscrew on the support bearing adjustment shaft. 8. Use the knurled knob to position the support bearing approximately 0.016" behind the blade, as illustrated in the figure below. 0.016'' Adjusting Blade Guide Bearings Properly adjusting the blade guides provides sideto-side support to help keep the blade straight while cutting, which is essential to making accurate cuts. Tool Needed Qty Hex Wrench 4mm.....................
4. Loosen the thumbscrew shown in the figure above, then use the knurled knob to adjust the guide bearings laterally so that the bearing faces are just behind the blade gullet, as illustrated in the following figure. 6. Loosen both cap screws behind the guide bearings, then rotate the adjustment cap screws so the bearings evenly and lightly touch the sides of the blade (see the illustration in the following figure).
Table Tilt Calibration When properly adjusted, the positive stop bolt enables the table to be quickly returned perpendicular with the blade. 5. Completely raise the upper blade guide assembly, then place the machinist's square flat on the table and against the side of the blade, as illustrated in the figure below. To tilt the table to the left, the positive stop bolt must be lowered from its correct height, then readjusted after the table is returned to 0°.
Aligning Table 5. To ensure cutting accuracy when the table is first installed, the table should be aligned so the miter slot is parallel to the bandsaw blade. Tools Needed Qty Straightedge 2'....................................................1 Fine Ruler............................................................1 Masking Tape......................................As Needed Wrench 10mm.....................................................
Aligning Fence To ensure accurate cutting when using the fence, the face of the fence must be parallel to the table miter slot and, thus, to the side of the blade. Tools Needed Qty Hex Wrench 5mm................................................1 4. Loosen the four fence adjustment cap screws shown in the figure below, adjust the fence parallel to the miter slot, then re-tighten the cap screws to secure the setting. Cap Screws To align the fence parallel with the miter slot: 1.
SECTION 4: OPERATIONS Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand. Due to the generic nature of this overview, it is not intended to be an instructional guide.
Disabling & Locking Switch Workpiece Inspection The ON/OFF switch can be disabled and locked by inserting a padlock through the ON button, as shown. Locking the switch in this manner can prevent unauthorized operation of the machine, which is especially important if the machine is not stored inside an access-restricted building. Some workpieces are not safe to cut or may require modification before they are safe to cut.
Guide Post Table Tilt The guide post, shown in the figure below, connects the upper blade guide assembly and blade guard to the bandsaw. The table can be tilted when making angle or bevel cuts. The guidepost allows these components to be positioned above the workpiece at a distance that provides the greatest support to the blade and minimizes operator exposure to the blade. We recommend positioning the blade guides so that they just clear the workpiece.
Blade Speed Adjustment Cap Screw The Model G0555/G0555P offers blade speeds of 1500 and 3200 FPM. For general woodworking and most cutting operations, we recommend using the 3200 FPM speed. Keep in mind, the results from different speeds are related to the type of workpiece, the blade being used for the operation, and the feed rate. Hinge Cap Screw Use the chart below as a general guide to blade speed: Type of Cutting Operation Figure 44. Locations of the motor adjustment and hinge cap screws.
Blade Information Blade Dimensions Length Range.................................... 92 1⁄ 2"–93 1⁄ 2" Width Range...............................................1⁄ 8"– 3 ⁄4" • Straight Cutting: Use the largest width blade that you own. Large blades excel at cutting straight lines and are less prone to wander.
Tooth Pitch Blade Breakage Measured as TPI (teeth per inch), tooth pitch determines the number of teeth. More teeth per inch (fine pitch) will cut slower, but smoother; while fewer teeth per inch (coarse pitch) will cut rougher, but faster. As a general rule, choose blades that will have at least three teeth in the material at all times. Use fine-pitched blades on harder woods and coarse-pitched blades on softer woods. Many conditions may cause a bandsaw blade to break.
Blade Change Blade Installation 1. DISCONNECT BANDSAW FROM POWER! 2. Perform Steps 2–6 in the previous Blade Removal procedure. Always disconnect power to the machine when changing blades. Failure to do this may result in serious personal injury. 3. Put on heavy leather gloves, position the blade so that the teeth are facing to the right and down toward the table, then slide it through the table slot. Note: If the teeth will not point downward in any orientation, the blade is inside-out.
Basic Cutting Tips Ripping Here are some basic tips to follow when operating the bandsaw: "Ripping" means cutting with the grain of the wood stock. For plywood and other processed wood, ripping simply means cutting down the length of the workpiece. • Replace, sharpen, and clean blades as necessary. Make adjustments periodically to keep the saw running in top condition. To make a rip cut: • Use light and even pressure while cutting.
Crosscutting Resawing Crosscutting is the process of cutting across the grain of wood. For plywood and other processed wood, crosscutting simply means cutting across the width of the material. "Resawing" means cutting the thickness of a board into two or more thinner boards (see the figure below for an example). The maximum board width that can be resawn is limited by the maximum cutting height of the bandsaw. To make a 90˚ crosscut: 1. Mark the workpiece on the edge where you want to begin the cut. 2.
Cutting Curves Stacked Cuts When cutting curves, simultaneously feed and turn the stock carefully so that the blade follows the layout line without twisting. Use either a narrower blade or a blade with more TPI (teeth per inch), or make more relief cuts, to avoid having to back the workpiece away from the blade, especially if the curve is sharp. One of the benefits of a bandsaw is its ability to cut multiple copies of a particular shape by stacking a number of workpieces together.
ACCESSORIES SECTION 5: ACCESSORIES Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to the newest copy of the Grizzly Catalog for other accessories available for this machine. Order Online at grizzly.
G7315Z—Super Heavy-Duty SHOP FOX® Mobile Base This patented, super heavy-duty mobile machine base is the strongest mobile base on the market. 18" x 24 1⁄ 2" minimum and adjusts to 28 1⁄ 2" x 33 1⁄ 2". Maximum 1200 lb. capacity. This base is extremely stable with outrigger type supports and a four wheel system. Weighs 38 lbs. G1163—1HP Floor Model Dust Collector G0710—1HP Wall-Mount Dust Collector G3591—30 Micron Replacement Bag H4340—3.
SECTION 6: MAINTENANCE ALWAYS disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily • • • • Check/correct loose mounting bolts. Check/correct damaged or worn saw blade. Check/correct worn or damaged wires. Correct any other unsafe condition.
Lubrication The bearings on this bandsaw are pre-lubricated and sealed at the factory, and require no lubrication for the life of the bearings. All bearings are standard sizes, and replacements can be purchased from our parts department or a bearing supply store. Redressing Rubber Tires As the bandsaw ages, the rubber tires on the wheels may need to be redressed if they harden or glaze over. Redressing the rubber tires improves blade tracking and reduces vibration/blade lead.
SECTION 7: SERVICE Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Machine does not start or a breaker trips. 1. Power supply is at fault/switched OFF. 1.
Cutting Operations Symptom Possible Cause Possible Solution Machine slows when operating. 1. Feeding workpiece too fast. 2. Blade is dull. 1. Reduce feed rate. 2. Replace blade (Page 37). Ticking sound when the saw is running. 1. Blade weld contacting guide/support bearings 1. Use file or stone to smooth and round the back of the blade; slightly loosen the blade guides. (a light tick is normal). 2. Inspect and replace blade if necessary (Page 37). 2. Blade weld may be failing.
V-Belt Tension Tensioning V-Belt Tool Needed Qty Hex Wrench 6mm................................................1 To ensure optimum power transmission from the motor to the blade, the V-belt must be in good condition and operate under proper tension. To properly tension the V-belt: V-belt tension should be checked at least every month—more often if the bandsaw is used daily.
Replacing V-Belt To ensure optimum power transmission from the motor to the blade, the V-belt must be in good condition and operate under proper tension. If the belt shows signs of cracks, fraying, and excessive wear, replace it. Tools Needed Qty Hex Wrench 6mm................................................1 Wrench or Socket 13mm.....................................1 Replacement V-Belt (Part No. P0555068)..........1 To replace the V-belt: 1. DISCONNECT BANDSAW FROM POWER! 2.
Wheel Alignment Straightedge Heat, vibration, wandering, blade wear, tire wear and overall bandsaw wear are considerably decreased when the wheels are parallel and coplanar. Additionally, wheels that are parallel and coplanar automatically track the blade by balancing it on the crown of the wheel—this is known as “coplanar tracking.” Parallel, Not Coplanar Coplanar Wheel alignment is one of the most critical factors for optimal performance from your bandsaw.
—If the wheels are parallel and coplanar, the straightedge will touch the top and bottom rims on both wheels. No further adjustment is required. 3. —If the wheels are parallel but not coplanar, the straightedge will touch the top and bottom rims on one wheel, but will not touch either rim on the other wheel. In this case, shim the wheel that does not touch the straightedge, as instructed in the following Shimming a Wheel procedure.
Upper Wheel Lateral Adjustment If the upper wheel is tilted laterally (side to side), perform the following procedure to make it coplanar with the lower wheel. There are two set screws in the upper wheel bracket, shown in Figures 65–66, that adjust the wheel tilt from side to side. Front Adjustment Set Screw Tools Needed Qty Hex Wrench 2.5mm.............................................1 Wrench or Socket 19mm.....................................1 To adjust the upper wheel laterally: 1.
Blade Lead To skew your fence: 1. Cut a piece of scrap wood approximately 3⁄4" thick x 3" wide x 17" long. On the wide face of the board, draw a straight line parallel to the long edge. 2. Slide the bandsaw fence out of the way and cut halfway through the board on the line by pushing it into the blade. Turn the bandsaw OFF and wait for the blade to stop. Do not move the board. 3. Clamp the board to the bandsaw table, then slide the fence over to the board so it barely touches one end of the board. 4.
Blade Tensioner The blade tensioner may need to be reset for one of the following reasons: • The blade tension quick release lever will not move down into the horizontal position when the tension scale is correctly adjusted for the installed blade. • You have installed a blade of a different length. Tool Needed Qty Hex Wrench 2.5mm.............................................1 To reset the blade tensioner: 1. DISCONNECT BANDSAW FROM POWER! 2.
Fence Scale Calibration You may need to recalibrate the fence scale after changing or adjusting the blade, or if the scale is not producing accurate cuts. Recalibrate the fence scale by adjusting the hairline indicator on the fence and testing your adjustment by cutting a piece of scrap wood. 4. If the reading on the scale is not the same as the width of the cut workpiece, loosen the two screws on the magnifying window (see Figure 69) and adjust it to match the width of the cut workpiece.
machine SECTION 8: WIRING These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully. If there are differences between your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine.
Wiring Diagram Start/Stop Switch NO B1 A1 B2 A2 B3 A3 FFO Ground Figure 70. Motor and ON/OFF switch locations.
Model G0555/G0555P (Mfg.
Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 1 2 3 4 5 6 7 8 9 10 11V2 11V2-1 11V2-2 11V2-3 11V2-4 11V2-5 11V2-6 11V2-7 11V2-8 11V2-9 11V2-10 11V2-11 12 13 14V2 15 16 17 18 19 20 21 23 24 25 26 27 28 28 29 30A 30A-1 31 32 33A 34 35 35-1 35-2 35-3 38 39 40 41 42 43 44 P0555001 P0555P001 PB80M PW08M PN13M P0555005 P0555006 P6204LLU PK23M P0555009 PS16M P0555011V2 P0555011V2-1 P0555011V2-2 P0555011V2-3 P0555011V2-4 P0555011V2-5 P0555011V2-6 P0555011V2-7 P6202ZZ P6205ZZ P0555011V2-10 P0
Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 106 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 HEX BOLT M8-1.25 X 30 POINTER FLANGE SCREW M5-.8 X 6 KNOB M10-1.5 HEX BOLT M10-1.5 X 50 HEX BOLT M8-1.25 X 80 HEX NUT M8-1.25 MITER GAUGE ASSEMBLY CAP SCREW M8-1.25 X 25 LOCK WASHER 8MM FLAT WASHER 8MM STEEL BALL COMPRESSION SPRING 1.5 X 5 X 9 SET SCREW M10-1.5 X 10 SET SCREW M8-1 X 35 MICRO ADJUSTING NUT 1.
Stand 205 204 206 207 208 202 201 211 212 212 211 209 213 210 REF PART # DESCRIPTION REF PART # DESCRIPTION 201 201 202 204 205 205 206 207 STAND TOP (G0555) STAND TOP (G0555P) CARRIAGE BOLT M8-1.25 X 16 FLANGE NUT M8-1.
Fence 303 318 316 312 323 304 311 320 307 308 322 313 315 309 302 322 305 326 325 323 320 317 310 300 327 306 321 324 314 319 301 REF PART # DESCRIPTION REF PART # DESCRIPTION 300 301 302 303 304 305 306 307 308 309 310 311 312 313 FENCE KIT ASSEMBLY W/RAILS FRONT FENCE RAIL FENCE BASE FENCE MOUNT ROD LOCK SHAFT SPRING PLATE SPACER PLATE FENCE SLEEVE LOCK HANDLE FENCE STAND-OFF SCALE WINDOW CAP SCREW M6-1 X 60 LOCK CAM 314 315 316 317 318 319 320 321 322 323 324 325 326 327 REAR FENCE
Labels 146 144V2 216 144V2 155 145 145 148 155 148 147 148 147 148 157 149 156 218 217 214 REF PART # DESCRIPTION REF PART # DESCRIPTION 144V2 144V2 145 146 147 148 149 P0555144V2 P0555P144V2 PLABEL-11 P0555146 PLABEL-18 PLABEL-23 PLABEL-14 MACHINE ID LABEL V2.05.11 (G0555) MACHINE ID LABEL V2.05.
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email ________________________ Invoice # _________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary basis.
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O.
WARRANTY AND RETURNS WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777