Instructions / Assembly

ManualsBrandsGronomics ManualsStorage & Organization3 ft. x 10 ft. x 8 ft. Pergola Planter Safe Finish

www.gronomics.com East Bethel, MN USA 763-753-7374

Continued

Parts Identiﬁ cation Box 1

Remove contents from Box 1 of 3.

Stack matching pieces in piles. Using the

parts list, locate and count the individual

pieces and verify that you have received

the correct number of pieces.

NOTE: It is recommended to place a

protective layer between the ground and

the pieces during assembly. This will help

prevent damage to the pieces.

1 2

3 4

Box 1 of 3

ITEM QTY. PART # DESCRIPTION

1 2

FL2236

Fabric Liner, 22” x 36”

2 4 3100 Post Cap, 4” x 4” x 1-1/2”

3 4 1451 Narrow Center Side Rail, 14-1/2” x 2-1/2” x 1”

4 4 1551 Corner Notched Bottom Board, 15-1/2” x 4-1/2” x 1”

5 8 1450 Side Rail, 14-1/2” x 5-1/2” x 1”

6 8 1550 Bottom Board, 15-1/2” x 5-1/2” x 1”

7 4 3103 Narrow Center Side Rail, 31” x 2-1/2” x 1”

8 4 3102 Side Rail w/Cleat, 31” x 5-1/2” x 1”

9 4 3101 Side Rail, 31” x 5-1/2” x 1”

10 2 3101L Side Rail w/Logo, 31” x 5-1/2” x 1”

11 4 3201 Corner Post, 4” x 4” x 32”

12 2 7022 Support Plate

13 2 7021 Pentagon Cap

14 12 CS8-112ZY 8 x 1-1/2” GRK Screw (Trellis)

15 20 RSS516-234ZY RSS 5/16 x 2-3/4” GRK Screw (Support Plate)

16 8 RSS516-234ZY RSS 5/16 x 2-3/4” GRK Screw (Posts)

17 12 R410-4ZY R4 10 x 4” GRK Screw (Crosspieces into Trusses)

ergola Planter 18” x 34”

Assembly Instruction

ITEM #: PP2 18-34

ITEM #: PP2 18-34S

Packaged & Inspected by: Date:

Torx® T15

Torx® T25

Torx® T30

If any pieces are missing or replacement

parts are required, contact Gronomics at

1-855-299-6727.

Summary of content (8 pages)

PAGE 1
Pergola Planter 18” x 34” Assembly Instruction 1 ITEM #: PP2 18-34 ITEM #: PP2 18-34S Parts Identification Box 1 Remove contents from Box 1 of 3. Stack matching pieces in piles. Using the parts list, locate and count the individual pieces and verify that you have received the correct number of pieces. 11 1 2 3 4 5 7 6 8 9 10 If any pieces are missing or replacement parts are required, contact Gronomics at 1-855-299-6727.
PAGE 2
Parts Identification Box 2 Remove contents from Box 2 of 3. Stack matching pieces in piles. Using the parts list, locate and count the individual pieces and verify that you have received the correct number of pieces. 19 18 If any pieces are missing or replacement parts are required, contact Gronomics at 1-855-299-6727. NOTE: It is recommended to place a protective layer between the ground and the pieces during assembly. This will help prevent damage to the pieces. Box 2 of 3 ITEM 18 19 3 QTY.
PAGE 3
4 5 Corner Post Assembly Locate one 4” x 4” x 80” corner post (Item 21) marked with an “X” and one 4” x 4” x 80” corner post (Item 22) marked with an “O”. Place the two posts flat on the ground with slots facing up and slots facing the inside. Ensure that the notches face outward. Locate and install one 31” x 5-1/2” side rail w/cleat (Item 8) (with cleat facing you) into the upper (wide) part “X” of the slot on the two posts.
PAGE 4
6 7 Side Rail Assembly Locate and install one 31” x 5-1/2” side rail w/cleat (Item 8) (cleat facing down) into the upper (wide) part of the slot on the two posts and slide down to the bottom of the slot. Truss Assembly Locate two 2” x 8” x 64” trusses (Item 18), one pentagon cap (Item 13) and one support plate (Item 12). Place the pentagon cap on the ground (face down). Place the two trusses on the pentagon cap.
PAGE 5
8 Planter Box Assembly Option Assembled Pergola Planter with planter boxes facing in. Assembled Pergola Planter with planter boxes facing out. Planter Boxes Facing In Planter Boxes Facing Out NOTE: The pergola planter boxes can be assembled with the planter boxes facing in. If assembling the planter boxes facing in, see steps 9 & 10. 9 NOTE: The pergola planter boxes can be assembled with the planter boxes facing out. If assembling the planter boxes facing out, see steps 11 & 12.
PAGE 6
10 Planter Box Installation (Facing In) Continued Place the second truss assembly on the top of the planter box assemblies (pentagon cap facing up). Pentagon Cap Facing Up Angled Notch Position the outside of the corner posts approximately 11” from the end of the truss assembly. Angled Notch 11” 11” 16 16 Verify that the truss assembly is contacting the angled notch on both 80” posts. Install two 5/16 x 2-3/4” (Item 16) screws through the slot in the 80” post and into the truss assembly.
PAGE 7
12 Planter Box Installation (Facing Out) Continued Place the second truss assembly on the top of the planter box assemblies (pentagon cap facing up). Angled Notch Position the outside of the 80” corner posts approximately 18” from the end of the truss assembly. Angled Notch Pentagon Cap Facing Up 18” 18” 16 16 Verify that the truss assembly is contacting the angled notch on both 80” posts. Install two 5/16 x 2-3/4” (Item 16) screws through the slot in the 80” post and into the truss assembly.
PAGE 8
14 16 Cap Assembly Trellis Assembly Locate the 29” x 52” trellis assemblies (Item 20). Extend one trellis assembly. Place the trellis assembly onto the top of the planter box and slide over until all the boards contact the 80” post. This will help square up the trellis before installing. Remove the rubber cap from the corner posts studs of the planter boxes. 20 Align the hole of the 4” x 4” post cap (Item 2) with stud and tighten until the cap makes contact with the post.