Instructions / Assembly

ManualsBrandsGronomics ManualsKitchen32 in. W x 45 in. H x 9 in. D Vertical Garden Bed

www.gronomics.com East Bethel, MN USA 763-753-7374

Continued

Using the parts list, locate and count the individual

pieces and verify that you have received the correct

number of pieces.

Check all the pieces for damage. If any pieces are

damaged or missing, contact Gronomics at www.

gronomics.com.

Vertical Garden Bed Pre-Assembled

32” x 45” Assembly Instruction

Parts List

ITEM QTY. PART # DESCRIPTION

1 1 VG32-45 Vertical Garden Bed 32”W x 45”H x 9”D

2 1 YFL Fabric Liner 36” x 10-1/4”

3 2 Screw, RSS GRK 10 x 2-3/4”

4 1 GBDIK Garden Bed Irrigation Kit (Contains Items 5 - 7)

5 1 Irrigation Tubing 18’

6 1 Hose Connector

7 5 Eyelet Screws

Parts Identiﬁ cation

Summary of content (6 pages)

PAGE 1
Vertical Garden Bed Pre-Assembled 32” x 45” Assembly Instruction 1 Parts Identification 1 Using the parts list, locate and count the individual pieces and verify that you have received the correct number of pieces. 2 Check all the pieces for damage. If any pieces are damaged or missing, contact Gronomics at www. gronomics.com. 3 5 6 4 7 ITEM 1 2 3 4 5 6 7 QTY.
PAGE 2
Angled Front Shelf Board Removal Remove the five angled front shelf boards. Remove Angled Shelf Boards Remove Angled Shelf Boards Position Logo Upside Down 3 Irrigation Kit Assembly NOTE: The irrigation tubing can be routed through the left side or the right side panel hole. LEFT SIDE PANEL ROUTING- Locate and install five eye bolts (Item 7) into the side rails. Install the eye bolts into the pre-drilled holes in the side panels marked with a Red “X”. (Left side panel (Red “X”) routing shown).
PAGE 3
4 Irrigation Kit Assembly Continued Irrigation Tubing End With Plug NOTE: Left side panel routing shown. Locate the irrigation tubing (Item 5). Route the irrigation tubing (end with plug) through the hole of the left panel and weave the irrigation tubing through the eye bolts (bottom to top). 5 Left Side Panel Hole 5 Right Side Panel Hole Irrigation Kit Assembly Continued Locate the hose connector and screen (Item 6). Install the screen inside the hose connector (screen facing out).
PAGE 4
Position Logo Upside Down 6 Irrigation Kit Assembly Continued Remove the plug from the end of the irrigation tubing. Cut the tubing to the desired length. Re-install the plug into the end of the irrigation tubing. NOTE: If the irrigation tubing needs to be cut shorter, always cut the hose in front of or behind the drip section (enlarged section) of the irrigation tubing.
PAGE 5
Position Logo Upside Down 8 Stabilizing The Garden Bed NOTE: The angled front shelf board with logo may need to be removed to access screws while fastening the vertical garden to the structure. NOTE: The garden bed is not intended for hanging on a wall or struture. 3 Angled Front Shelf Boards w/Logo Locate and install the two screws (Item 3) into the pre-drilled holes of the top back board. Fasten the vertical garden to a stable structure.
PAGE 6
Position Logo Upside Down 10 Planting Bedding NOTE: Before adding the plant bedding, verify that the vertical garden is securely fastened to a stable structure. Verify that all back rails and shelf rails are completely installed. CAUTION: When filling the vertical garden with plant bedding, support the irrigation tubing while filling. This will help prevent damage to the irrigation tubing. Slowly place the plant bedding into the top of the vertical garden.