Instructions / Assembly

ManualsBrandsGronomics ManualsOutdoor Benches6 ft. White Oak Wood Signature with Brown Finish Wood Outdoor Bench

WWW.gronomics.com East Bethel, MN USA

763-753-7374

Gronomics Signature Bench 6 FT.

Assembly Instruction

Continued

Parts List

ITEM QTY. PART # DESCRIPTION

1 6 GSB7200 Surface Panel Boards - Prefinished 72”

2 1 GSBLHL LH Leg Assembly

3 1 GSBRHL RH Leg Assembly

4 2 GSBF-Spacer Spacer (Seat)

5 2 GSBB-Spacer Spacer (Backrest)

6 28 RSS14-212ZY Screw 1/4” x 2-1/2”

7 8 RSS516-312ZY Screw 5/16” x 3-1/2”

Stack matching pieces in piles. Using the parts list,

locate and count the individual pieces and verify that

you have received the correct number of pieces.

If any pieces are missing or replacement parts are

required, contact Gronomics at 1-855-299-6727.

NOTE: It is recommended to place a protective layer

between the ground and the pieces during assembly.

This will help prevent damage to the pieces.

Parts Identification

Item #: GSB-6FT

Torx® T30

Torx® T25

Packaged & Inspected by: Date:

Summary of content (6 pages)

PAGE 1
Gronomics Signature Bench 6 FT. Assembly Instruction 1 Parts Identification Item #: GSB-6FT Stack matching pieces in piles. Using the parts list, locate and count the individual pieces and verify that you have received the correct number of pieces. 1 2 3 If any pieces are missing or replacement parts are required, contact Gronomics at 1-855-299-6727. Torx® T25 Torx® T30 NOTE: It is recommended to place a protective layer between the ground and the pieces during assembly.
PAGE 2
Seat / Leg Assembly Place three surface panel boards (Item 1) onto a table or work bench. 3 3 Place the RH leg assembly (Item 3) as shown. Repeat procedure at opposite end for the LH leg assembly. 9” 9” 1 3 Seat / Leg Assembly Continued NOTE: Make sure the inner surface panel board (Item 1) is tight against the leg assemblies (Items 2 & 3) back rest supports. 6 3 2 NOTE: Screws will only be installed to the inner surface panel board in this step.
PAGE 3
4 Seat / Leg Assembly Continued Place the seat spacers (Item 4) between the inner surface panel board and center surface panel board as shown. This will allow a 1/2” gap between the boards. 6 NOTE: Make sure the center surface panel board is snug to the seat spacers and that the boards are flush at each end. Install two 1/4” x 2-1/2” screws (Item 6) into the pre-drilled holes of the leg assemblies at each end and tighten. Center Board Remove the seat spacers.
PAGE 4
6 Seat / Leg Assembly Continued Install six 1/4” x 2-1/2” screws (Item 6) into the predrilled holes of the leg assembly. Repeat procedure for the leg assembly at opposite end. 6 6 7 Backrest Assembly Remove the bench from the work table and place the bench on the ground as shown. 1 Place the backrest spacers (Item 5) and backrest surface panel board (Item 1) as shown. This will allow a 1-3/8” gap between the backrest surface panel boards.
PAGE 5
8 Backrest Assembly Continued Place the backrest spacers (Item 5) at the top of the lower backrest board. Place the upper backrest board (Item 1) onto the spacers. 1 5 5 NOTE: Make sure the top backrest surface panel board ends are flush with the bottom backrest surface panel board ends. Install four 5/16” x 3-1/2” screws (Item 7) into the pre-drilled holes and tighten. Remove the backrest spacers. 7 9 Backrest Top Rail Assembly Place the backrest top rail surface panel board (Item 1) as shown.
PAGE 6
10 Completed Assembly Gronomics Signature Bench completed assembly. WWW.gronomics.