User manual

ManualsBrandsGROTHE ManualsOutlets & SocketsFlush mount PIR motion detector 180 ° Relay White IP20

McGuard UP

WALL SWITCH

PRESENCE DETECTOR

INSTRUCTION MANUAL

Rated Voltage 220-240V~ 50 / 60Hz

Load

Incandescent Lamp : Max. 2000W

AC Halogen Lamp : Max. 1000W

LV Halogen Lamp : Max. 1000VA / 600W

(traditional)

Max. 1000VA / 900W

(electronic)

Fluorescent Lamp : Max. 900VA / 100μF

25 x (1 x 18W); 12 x (2 x 18W);

5 x (1 x 36W); 7 x (2 x 36W);

10 x (1 x 58W); 5 x (2 x 58W)

LED Lamp : Max. 400W

Energy Saving Lamp : Max. 600VA / 400W

(incl. CFL and PL Lampe)

Power Approx. 0,5W

consumption:

Detection 180° up to 8m forward und 6m each sideward

Range at hight of 1.2m

LUX Adjustable from approx. 10Lux to (∞) and

Adjustment “ ” (learning range: 10Lux - 2000Lux)

Auto Off Time Adjustable from approx. 10Sek to 30Min, and

Adjustment Test &

Mic. Sensitivity + (max.) / -(off)

TECHNICAL SPECIFICATIONS

Operation Mode Manual ON / AUTO / Manual OFF

Operating Temperature 0C° bis +45C°

Environmental Protection IP40

TECHNICAL SPECIFICATIONS

Installation and assembly of electrical equipment

must be carried out by qualified electricians.

Contact a qualified electrician in the event of fault

or break down.

CAUTION!

- A circuit breaker (250VAC, 10A) type C according to EN60898-1 of load shall be

installed in the fixed wiring for protection.

- Do not mount on conductive surface.

- Do not open the enclosure frequently.

- Turn off power when change the light sources.

- High in-rush current would be caused when bulbs of certain brands burned which

might damage the unit permanently.

1 PACKAGE CONTENTS

Pattern

Item

Quantity

Detector

Lens shield label

Manual

2 PRODUCT DESCRIPTION

Der Mc Guard is an indoor wall switch presence detector, and is ideally to

be located in small-scaled stores or factories, offices, homes, at the places

such as corridors, staircase, archive rooms, cellars, rest rooms, play rooms,

garages, etc.

2.1 Features

- The stylish cosmetic design of integrating lens with front housing and

invisible knobs for restricting the liberty of unauthorized operation.

- Superior lens pattern and well distributed as well as concentrated

detecting beams provide high sensitivity.

- In addition to PIR sensing, the detector can be properly triggered by the

sound too.

- Excepting the provided Lux values, the ambient light level can be read-in

as the Lux value for more flexible application.

- Three practical operation modes (Manual ON / AUTO / Manual OFF)

available for user’s flexible application.

- The connected lighting can be manually switched on/off by connecting a

push button switch to the detector.

- The decorative Frame of 50 x 50 mm fits most European standard wall

switches.

2.2 Dimension

80 x 80 x 51,5mm (See FIG. 1)

FIG. 1

Bild 3

3.2.2 Manual on / off switching by using push button to activate R

terminal

An additional push button can be connected between terminal R and L

for manual on / off operation (case 1: on --> off; case 2: off -->on). While

pressing push button (≤1sec):

Case 1: Manual off switching (Lux settings is invalid):

Under the light on status, the light can be manually switched off by short

pressing ( 1sec) the push button. During this operation mode, once the

detector is triggered by movement, the light keeps off within the set switch

off delay time. Until there is no movement detected and the pre-set switch

off delay time has reached, the detector resumes to work according to the

previous operation mode set by knobs or IR. To press the push button

(≤1sec) during the light manual off period will activate the manual light on

function (working as the Case 2).

Case 2: Manual on switching (Lux settings is invalid): Under the light

off status, the light can be manually switched on by short pressing ( 1sec)

the push button. During this operation mode, once the detector is triggered

by movement, the light keeps on within the pre-set switch off delay time.

Until there is no movement detected and the pre-set switch off delay time

has elapsed, the detector resumes to work according to the previous

operation mode set by knobs or IR. To press the push button (≤1sec) during

the light manual on period will activate the manual light off function (working

as the Case 1).

3.2.3 Auto sensitivity adjustment function To raise the sensitivity of

detector after load is switched on can reduce the possibility of false-off

problem. When the load is on, the sensitivity of detector will be raised

automatically. When the load is off, the sensitivity of detector will return to

normal standby condition.

3.2.4 Acoustic control function

By setting the Mic. knob to “+” position, this function is enabled. This

function is only available when detector works in auto mode and the

detector is activated by movement at first, then the acoustic sensor control

function is workable. Once the detector is firstly triggered by movement to

turn on the load, then within 8sec, the acoustic sensor is used as an

auxiliary sensor to be activated by sound in order to renew the delay off

time and to continuously switch on the load. If there is no sound detected

within 8sec. after the first triggering by movement, the acoustic sensor is

ineffective.

3.3 Wiring

3.3.1 Normal operation (See FIG.5)

3.3.3 One detector controls staircase time switch (Time knob sets at )

(See FIG.7)

FIG. 5

FIG. 7

Bild 2

3.3.2 Two detectors control a load (See FIG.6)

3.2 Function

3.2.1 Ambient light appraisal

According to the changeable ambient light level, detector can postpone

delay time of switching light on and off to avoid unnecessarily switching due

to rapid ambient light change:

Ambient light level changes from bright to dark:

If the ambient light level keeps be lower than the preset Lux value for

10sec, the light will be automatically switched on after 10sec. (LED will be

on 10sec for indication).

Ambient light level changes from dark to bright:

If the ambient light level continuously exceeds the switch off Lux value for

5min, there are different reactions according to the time setting value.

Time setting ≥ 5min, the light will be automatically switched off after 5min.

Time setting < 5min, the light will be automatically switched off when the set

time reached if no movement is detected during the 5min. But if there is

movement detected within the 5min, the time will be reset upon detection

and until 5min later, the light is switched off.

3.1.3 Helpful tips for installation

Since the detector is in response to temperature change, the

following conditions should be avoided (See FIG.4-A & FIG.4-B):

- Avoid aiming the detector toward the objects which may be swayed in the

wind, such as curtain, tall plants, miniature garden, etc.

- Avoid aiming the detector toward the objects whose surfaces are highly

reflective, such as mirror, monitor, etc.

- Avoid mounting the detector near heat sources, such as heating vents, air

conditioning, vents as dryers, lights, etc.

3.1.2 Pay attention to the walking direction in the test proceeding. It is more

sensitive to movement across the detector and less sensitive to

movement directly toward to detector which will reduce the detection

coverage (See FIG.3).

3 INSTALLATION AND WIRING

Please disconnect power completely and read the

entire instruction manual carefully before installation.

3.1 Select a proper location

3.1.1 Detection coverage

It is recommended to install at the height of 0.8m - 1.5m. The forward

detection distance can reach up to 8m and 180 detection angle (See

FIG.2).

Side view

Top view

Side view

FIG. 4-B

FIG 4-A

Taster

Last

Push button

Load

Push button

FIG. 6

Staircase time switch

Push button

Load

Push button