Install Instructions
Table Of Contents
- English (US)
- 1. Limited warranty
- 2. Symbols used in this document
- 3. General information
- 4. Mechanical installation
- 5. Electrical installation
- 5.1 Supply voltage
- 5.2 Connection to the power supply (models 40-XX, 50-XX, 65-XX, 80-XX, 100-XX)
- 5.3 Connection to the power supply (models 32-XX)
- 5.4 Connection diagram
- 5.5 Input/output communication
- 5.6 Analog input for external sensor
- 5.7 Electrical connection for external sensor
- 5.8 Priority of settings
- 6. First start-up
- 7. Settings
- 8. Menu overview
- 9. Control panel
- 10. Menu structure
- 11. "Home" menu
- 12. "Status" menu
- 13. "Settings" menu
- 14. "Assist" menu
- 15. Selection of control mode
- 16. Fault finding
- 17. Sensor
- 18. Accessories
- 19. Technical data
- 20. Disposal
41
English (US)
18.2.1 Description of CIM modules
Module
Fieldbus
protocol
Description Functions
CIM 050
TM05 3812 1612
GENIbus
CIM 050 is a Grundfos
communication interface
module used for
communication with a
GENIbus network.
CIM 050 has terminals for the GENIbus connection.
CIM 100
TM05 3813 1612
LonWorks
CIM 100 is a Grundfos
communication interface
module used for
communication with a
LonWorks network.
CIM 100 has terminals for the LonWorks connection.
Two LEDs are used to indicate the actual status of the
CIM 100 communication.
One LED is used for indication of correct connection to the
pump, and the other is used to indicate LonWorks
communication status.
CIM 150
TM05 3814 1612
PROFIBUS DP
CIM 150 is a Grundfos
communication interface
module used for
communication with a
PROFIBUS network.
CIM 150 has terminals for the PROFIBUS DP connection.
DIP switches are used to set line termination.
Two hexadecimal rotary switches are used to set the
PROFIBUS DP address.
Two LEDs are used to indicate the actual status of the
CIM 150 communication.
One LED is used for indication of correct connection to the
pump, and the other is used to indicate PROFIBUS
communication status.
CIM 200
TM05 3815 1612
Modbus RTU
CIM 200 is a Grundfos
communication interface
module used for
communication with a
Modbus RTU network.
CIM 200 has terminals for the Modbus connection.
DIP switches are used to select parity and stop bits, to
select transmission speed and to set line termination.
Two hexadecimal rotary switches are used to set the
Modbus address.
Two LEDs are used to indicate the actual status of the
CIM 200 communication.
One LED is used for indication of correct connection to the
pump, and the other is used to indicate Modbus
communication status.
CIM 250
TM05 4432 2212
GSM/GPRS
CIM 250 is a Grundfos
communication interface
module used for GSM/GPRS
communication.
CIM 250 is used to
communicate via a GSM
network.
CIM 250 has a SIM-card slot and an SMA connection to
the GSM antenna.
CIM 250 also has an internal backup battery. Two LEDs
are used to indicate the actual status of the CIM 250
communication. One LED is used for indication of correct
connection to the pump, and the other is used to indicate
GSM/GPRS communication status.
Note: The SIM card is not supplied with CIM 250. The SIM
card from the service provider must support data/fax
service to use call service from PC Tool or SCADA.
The SIM card from the service provider must support
GPRS service to use Ethernet service from PC Tool or
SCADA.