Owner's Manual IP Cameras & Domes GCI-K1812W GCI-K1812W.59.1.18.05.
Content: 15. View User Information 47 1. Introduction 1 16. View Parameters 49 2. Important Safety Instructions 2 17. Factory Default 49 3. Package Contents 2 18. Software Version 50 4. Installation 2 19. Software Upgrade 51 20. Maintenance 52 1. Camera Overview 3 2. System Requirements 3 3. Ethernet Connection 3 4. Installation and Connection 4 5. Accessing the Camera 4 6. Video Resolution Setup 9 7. Browser-based Viewer Introduction 12 8. Home Page 13 9.
With the Power over the Ethernet (IEEE 802.3af) feature, the need of power outlets could be totally eliminated. Likewise installation and cabling cost can be significantly reduced. Additionally, its light weight and compact size offer a quick and simple installation on ceilings or walls of houses and vehicles. 2. Important Safety Instructions Be sure to use only the standard adapter that is specified in the specification sheet.
4.1. Camera Overview 4.2. System Requirements To perform the IP Camera via web browser, please ensure your PC is in good network connection, and meets the system requirements as described below. Personal Computer : 1.) Intel Pentium M, 2.16 GHz or Intel Core 2 Duo, 2.0 GHz 2.) 2 GB RAM or more Operating System : Windows XP / Windows VISTA / Windows 7 Web Browser : Microsoft Internet Explorer 6.
4.4. Installation and Connection To make sure that the camera is waterproof, please follow the following installation procedure: Step 1: Please refer to 4.3. Ethernet Installation to connect the cable. Step 2: Put the Rubber Washers into the holes that are located on both sides of the Bottom Plate of the Camera. Step 3: Aim the installation holes at the target installation position and fasten the screws to attach the Camera to the ceiling.
Step 2: The security alert window will pop up. Click “Unblock” to continue. Device Search : Step 3: Click “Find Device” again, afterwards all IP devices found will be listed on the page, as shown in the picture below. The IP Camera’s default IP address is: 192.168.1.1. Step 4: Double-click or right-click and select “Browse” to access the camera directly via the web browser.
Step 5: Then the dialogue box for entering the default user name and password (as shown below) will appear for login to the IP Dome Camera. The default login ID and password for the Administrator are: Login ID: admin Password: 1234 NOTE: ID and password are case sensitive. It is strongly advised to alter the administrator’s password due to security concerns. Please refer to section 9.2. Security for further details.
Step 2: The “Network Setup” page will come out. Select “DHCP,” and click on the “Apply” button at the bottom of the page. Step 3: Click on “OK” in the Note of setting the change. Wait for one minute to search again for the IP Camera. Step 4: Click on the “Find Device” button to search all the devices. Then select the IP Camera with the correct MAC address. After double-clicking on the IP Camera, the login window will appear. Step 5: Enter User name and Password to access the IP Camera.
The Information Bar (just below the URL bar) may come out and ask for permission to install the ActiveX Control for displaying video in browser (see the picture below). Right-click on the Information Bar and select “Install ActiveX Control…” to allow the installation. Then the security warning window will pop up. Click “Install” to carry on with the software installation. Click on “Finish” to close the GRUNDIG Viewer window when download is finished.
6. Video Resolution Setup The users can set up the Video Resolution on the Video Format page of the user-friendly browser-based configuration interface. The page “Video Format” can be found in the IP camera menu under the path: Streaming > Video Format.
English 10
For more streaming combinations with several streams, please refer to "Streaming" > "Video Format" in the camera menu.
7. Browser-based Viewer Introduction The picture below shows the Home page of the IP Camera’s viewer window. There are four tabs on the left (System, Streaming, Camera and Logout) and one tab on the right (Languages). System setting : The administrator can set host name, system time, admin password, network related settings, etc. Further details will be interpreted in chapter 9. System Related Settings.
8. Home Page In the Home page, there are several function buttons that are specified below. Display Mode (Screen Size Adjustment) : The display size of the image can be adjusted to x1/2 and full screen. Snapshot button : After pressing this button, the JPEG snapshots will automatically be saved in the appointed place. The default place of saving snapshots is: C:\. For changing the storage location, please refer to section 9.13. 'File Location (on PC)' for further details.
Multiple Languages Support : Multiple languages are supported for the viewer window interface. NOTE: The following functions are not available for the Browsers Firefox, Chrome, Safari and Opera: Full Screen Mode, Snapshot, Playback and Recording.
9. System Related Settings The picture below shows all categories under the “System” tab. Each category in the left column will be explained in the following sections. NOTE: The “System” configuration page is only accessible by the Administrator. 9.1. Host Name & System Time Setting Click on the first category in the left column; the page is shown below.
Host Name : The name is for camera identification (max. 30 characters). If an alarm function is enabled and is set to send an alarm message by Mail/FTP, the host name entered here will be displayed in the alarm message. Time Zone : Select the time zone you are in from the drop-down menu. Enable Daylight Saving Time : To enable DST, please check the item and then specify the time offset and DST duration.
Admin Password : Change the administrator’s password by putting in the new password in both text boxes. The input characters/numbers will be displayed as dots for security purposes. After clicking , the web browser will ask the Administrator for the new password for access. The maximum length of the password is 14 digits. NOTE: The following characters are valid: A-Z, a-z, 0-9, !#$%&’-.@^_~. Add User : Type in the new user name and password and click to add the new user.
: allows secure connections between the IP Camera and the web browser using the or the , which prevent others from snooping on your camera settings or Username/Password. It is required to install a self-signed certificate or a CA-signed certificate for implemention of . After clicking on the tab, the HTTPS setting page will be shown as in the figure below.
Create self-signed certificate : Before a CA-issued certificate is obtained, users can create and install a self-signed certificate first. Click on the button under “Create self-signed certificate” and provide the requested information to install a self-signed certificate for the IP Camera. Please refer to the last part of this section: "Provide the Certificate Information" for more details.
Install signed certificate : Click on the “Create Certificate Request” button to create and submit a certificate request in order to obtain a signed certificate from the CA (Certificate Authority). When the request is complete, the subject of the Created Request will be shown in the field. Click “Properties” below the Subject field, copy the PEM-formatted request and send it to your selected CA. When the signed certificate is returned, install it by uploading the signed certificate.
Provide the Certificate Information : To create a Self-signed HTTPS Certificate or a Certificate Request to CA, please enter the information as requested: - Country: Enter a 2-letter combination code to indicate the country the certificate will be used in. For instance, type in “GB” to indicate Great Britain. - State or province: Enter the local administrative region. - Locality: Enter other geographical information.
- Organisation Unit: Enter the name of the organisational unit to which the entity identified in “Common Name” belongs. - Common Name: Indicate the name of the person or other entity that the certificate identifies (often used to identify the website). - Valid days (Self-signed Certificate Only): Enter the period in days (1~9999) to indicate the valid period of the certificate. Click “OK” to save the Certificate Information after completing.
: The IP Camera can access a network protected by 802.1X/EAPOL (Extensible Authentication Protocol over LAN). To do this, users need to contact the network administrator to receive certificates, user IDs and passwords. CA Certificate : The CA certificate is created by the Certification Authority for the purpose of validating itself. Upload the certificate for checking the server’s identity.
9.3. Network When you click on the category , there will be a drop-down menu with several tabs including , , , and . : Users can choose to connect to the IP Camera through a fixed or dynamic (DHCP) IP address. The IP Camera also provides PPPoE (Point-to-Point Protocol over Ethernet) support for users who connect to the network via PPPoE.
Get IP address automatically (DHCP): The camera’s default setting is “Use fixed IP address”. Please refer to the previous section 6. Accessing the Camera for login with the default IP address. If “Get IP address automatically” is selected, after the IP Camera restarts, users can search the IP address through the installer program “GRUNDIG Finder.exe”, that is on the supplied CD. NOTE: The DHCP function can only be used if you have a DHCP server in the used network.
- Secondary DNS: Secondary DNS is a secondary domain name server that backs up the primary DNS. Use PPPoE : The PPPoE users need to enter the PPPoE Username and Password into the fields, and need to click on the “Save” button to complete the setting. Advanced : - Web Server port: The default web server port is 80. Once the port is changed, all users must be informed about the change for the connection to be successful.
DSCP Settings : The DSCP value range is from 0 to 63. The default DSCP value is 0, which means that DSCP is disabled. The IP Camera uses the following QoS Classes: Video, Audio and Management. - Video DSCP: This class consists of applications such as MJPEG over HTTP, RTP/RTSP and RTSP/HTTP. - Audio DSCP: This setting is only available for the IP Cameras which support audio. - Management DSCP: This class consists of the HTTP traffic: Web browsing. Click the “Save” button to complete the setting.
Traps for SNMP v1/v2 : Traps are used by the IP Camera to send messages to a management system about important events or status changes. - Enable Traps: Check the box to activate trap reporting. - Trap address: Enter the IP address of the management server. - Trap community: Enter the community to use when sending a trap message to the management system. Trap option : - Warm start: A Warm start SNMP trap signifies that the SNMP device, i.e. the IP Camera, performs a software reload.
UPnP Setting : - Enable UPnP: When UPnP is enabled, whenever the IP Camera is presented to LAN, the icon of the connected IP Cameras will appear in My Network Places to allow for direct access as shown below. NOTE: To enable this function, please make sure the UPnP component is installed on your computer. Please refer to chapter 16. Install UPnP Components for UPnP component installation procedure.
9.4. DDNS The Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronised with a dynamic IP address. In other words, it allows those using a dynamic IP address to be associated to a static domain name so that others can connect to it through this name. Enable DDNS : Check the item to enable DDNS. Provider : Select one DDNS host from the provider list. Host name : Enter the registered domain name in the field.
9.5. Mail The Administrator can can set up the sending of an e-mail via Simple Mail Transfer Protocol (SMTP) when a motion is detected. SMTP is a protocol for sending e-mail messages from server to server. SMTP is a relatively simple, text-based protocol, where one or more recipients of a message are specified and to whom the message text is transferred. The configuration page is shown below: Two sets of SMTP can be configured.
9.6. FTP The Administrator can set the sending of alarm messages to a specific File Transfer Protocol (FTP) site when motion is detected. Users can assign an alarm message to up to two FTP sites. The FTP setting page is shown below. Enter the FTP details, which include server, server port, user name, password and remote folder, into the fields. Click “Save” when the setting is finished.
9.7. HTTP A HTTP Notification server can listen for notification messages from IP Cameras by triggered events. The HTTP setting page is shown below. Enter the HTTP details, which include the server name (for instance, http://192.168.1.1/admin.php), user name, and password into the fields. triggered and notifications can then be sent to the specified server. Click “Save” when the setting is finished. Please refer to: 9.8. Motion Detection for HTTP Notification settings.
9.8. Motion Detection The Motion Detection function allows detecting suspicious motion and triggers alarms when motion volume in the detected area reaches/exceeds the determined sensitivity threshold value. In the Motion Detection setting page a frame (Motion Detection Window) is displayed in the Live View Pane. The Motion Detection Window is for defining the motion detection area. To change the size of the Motion Detection Window, move the mouse cursor to the edge of the frame and draw it outward/inward.
When a motion is detected, the signals will be displayed in the Motion window as shown below: The detailed settings of Motion Detection are described as follows: Motion Detection : You will be able to turn the Motion Detection on/off in the System section "Motion Detection". The default setting is: Off. Motion Detection Setting : Users can adjust various parameters of Motion Detection in this section. - Sampling pixel interval [1-10]: The default value is 1.
The pre-trigger buffer recording function allows users to check what happened to trigger the alarm. The pretrigger buffer time range is from 1 to 3 seconds. Select to set the recording duration after the alarm is triggered. The setting range is from 1 to 99999 seconds. Select to record the triggered video until the trigger is turned off.
The recording function allows users to check what happened to trigger the alarm. The pretrigger buffer time range is from 1 to 20 frames. On the other hand, the is for uploading a certain amount of images after the alarm input is triggered. The post-trigger buffer time range is from 1 to 20 frames. Check the box to upload the triggered images during a certain time or keep uploading until the trigger is off.
9.9. Network Failure Detection This function is used to detect network failure that might happen during camera operation. Detection Switch : Here you can turn the Network Failure Detection on and off. Detection Type : Here you can set an IP address that should be pinged in order to detect network failure. Please also set the interval (in minutes) for this pinging. Triggered Action (Multi-option) : The Administrator can specify alarm actions that will take place when motion is detected.
- Send Alarm Message by FTP: The Administrator can select whether to send an alarm message by FTP when Network Failure is detected. - Send Alarm Message by E-Mail: The Administrator can choose to send an alarm message by E-Mail when Network Failure is detected. 9.10. Tampering The Tampering Alarm function helps the IP Camera against tampering such as deliberate redirection, blocking, spray paint, lens covering, etc.
- Record Stream to SD Card: When you check this item, the alarm-triggered recording will be stored on your Micro SD/SDHC card when Tampering is detected. The pre-trigger buffer recording function allows users to check what happened to trigger the alarm. The pretrigger buffer time range is from 1 to 3 seconds. Select to set the recording duration after the alarm is triggered. The setting range is from 1 to 99999 seconds.
- Upload Image by E-Mail: After selecting this item, the Administrator can assign an e-mail address and configure various parameters as shown in the figure below. When tampering is detected, event images will be sent to the appointed e-mail address. The recording function allows users to check what happened to trigger the alarm. The pretrigger buffer time range is from 1 to 20 frames.
NOTE: Please format the Micro SD/SDHC card when using it for the first time. Formatting will also be required when a memory card has already been used on one device and was later transferred to another device with a different software platform. Device Information : When users insert the Micro SD/SDHC card, the card information such as the memory capacity and status will be shown in the Device Information section.
When the recording mode is set to “Always” (consecutive recording) in the submenu "Recording" and the Micro SD/SDHC card recording is also allowed to be enabled when triggered by events, once the events occur, the system will immediately implement the recorded events to the memory card. After event recording, the device will return to regular recording mode. - Remove: To remove a file, select the file first, and then click on the “Remove” button.
9.12. Recording (on Camera) In the Recording setting page, users can specify the recording schedule that fits the present surveillance requirement. Activating Micro SD/SDHC Card Recording : Two types of schedule mode are offered: "Always" and "Only during time frame". You can set up the time frame according to your requirements or you can choose “Always” to allow the Micro SD/SDHC Card Recording to be activated all the time. Please click on the “Save” button to confirm the schedule mode.
9.13. File Location (on PC) Users can specify a storage location for the snapshots and the live video recording. The default setting is: C:\. Once the setting is confirmed, click on “Save,” and all the snapshots and recordings will be saved in the designated location. NOTE: Please make sure the selected file path contains valid characters such as letters and numbers. NOTE: Users with the Windows 7 operating system on their PC need to follow the following procedure to be able to use the Snapshot function.
9.14. View Log File Click on the link to view the system log file. The content of this file provides useful information about configuration and connections after system boot-up.
9.15. View User Information The Administrator can view each user’s login information and their privileges (see section 9.2. Security). View User Login Information : All the users in the network will be listed in the “User Information” zone, as shown below.
View User Privilege : If you click on “Get user privacy” at the bottom of the page, the Administrator will be able to view each user’s privileges. As the picture above shows: User: 1:1:0:1 1:1:0:1 = I/O access : Camera control : Talk : Listen (see 9.2. Security) This denotes that the user has been granted the privileges of I/O access, Camera control and Listen.
9.16. View Parameters Click on this item to view the entire system’s parameter setting. 9.17. Factory Default The factory default setting page is shown below. Follow the instructions to reset the IP Camera to factory default setting if needed.
Set Default : Click on the “Set Default” button to recall the factory default settings. After 30 seconds the system will restart. NOTE: The IP address will also be restored to default (192.168.1.1). Reboot : When you click on the “Reboot” button, the system will restart without changing the current settings. 9.18. Software Version The current software version is displayed in the software version page, which is shown in the picture below.
9.19. Software Upgrade Software upgrade can be carried out on the “Software Upgrade” page, as shown below. NOTE: Make sure the upgrade software file is available before carrying out the software upgrade. The procedure of a software upgrade is as follows: Step 1: Click on “Browse” and select the following binary file to be uploaded: uImage+userland. NOTE: Do not change the upgrade file name, or the system will fail to find the file.
9.20. Maintenance Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera. This is especially convenient if you want to have the same configuration for multiple cameras. Export: Users can save the system settings by exporting the configuration file (.bin) to a specified location for future use. When you click on the “Export” button, the File Download window will pop up as shown below.
10. Streaming Settings 10.1. Video Format Video Resolution : Under the Video Resolution section, the available video resolution formats include MJPEG and H.264. Please refer to Chapter 6. Video Resolution Setup for more combination details. Click on “Save” to confirm the setting. Text Overlay Settings : Users can select these items to display data (date/time/text) on the live video pane. The maximum length of the string is 18 alphanumeric characters. Click “Save” to confirm the Text Overlay setting.
To rotate the image, users can select “Flip video”, for instance. Then the displayed image will be reversed as shown below. The following are descriptions of different video rotation types. - Flip video: If you select , the image will be rotated horizontally. - Mirror video: If you select , the image will be rotated vertically. - 90 degree counter-/clockwise: Selecting <90 degree counter-/clockwise> will inverse the image 90° counter-/clockwise.
10.2. Video Compression Users can specify the values for MJPEG/H.264 compression mode in the video compression page (see the picture below), depending on the application. MJPEG compression setting (MJPEG Q (Quality) factor): A higher value implies higher bit rates and a higher visual quality. The default setting is 35; the setting range is from 1 to 70. Click “Save” to confirm the setting. H.264-1 / H.264-2 / H.264-3 / H.264-4 bit rate: The default setting of H.264-1 is 4096 kdps and of H.264-2/H.264-3/H.
CBR mode setting : The CBR (Constant Bit Rate) mode can become the preferred bit rate mode if the available bandwidth is limited. It is important to take into account the image quality when you choose to use CBR mode. Click on “Save” to confirm the setting.
10.3. Video OCX Protocol In the Video OCX protocol setting page, users can select RTP over UDP, RTP over TCP, RTSP over HTTP or MJPEG over HTTP, for streaming media over the network. In the case of multicast networking, users can select the Multicast mode. The Video OCX Protocol page is as follows: Video OCX protocol setting options include: - RTP over UDP / RTP over RTSP (TCP) / RTSP over HTTP / MJPEG over HTTP (Select a mode according to your data delivery requirements.
10.4. Video Frame Rate Video frame skipping is for saving bandwidth if necessary. The setting page is shown below. MJPEG / H.264-1 / H.264-2 / H.264-3 / H.264-4 Frame Rate: The default setting of MJPEG/H.264-1/H.264-2/H.264-3/H.264-4 Frame Rate is 25 fps. The setting range is from 1 to 25. Click on to confirm the setting. NOTE: A lower frame rate will decrease video smoothness.
10.5. Video Mask There are five video masks which can be set by the users. Active Mask Function : - Add a Mask: When you check a Video Mask checkbox, a red frame will come out in the Live Video pane at the right side. Use the mouse to adjust the mask’s size and drag and drop the frame to place it on the target zone. NOTE: It is suggested to set the Video Mask twice as big as the object.
11. Camera Settings The picture below is the camera configuration page. Details of each parameter setting are described in the following subsections. 11.1. Exposure Setting Display of the Exposure pull-down menu: The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening, the amount of exposure by the sensor (shutter speed) and other exposure parameters. With this item, users can define how the Auto Exposure function works.
Manual Mode: - Fixed Shutter Mode: In this mode, a fixed shutter speed can be selected from the drop-down menu. The shutter speed range is from 1/10000 to 1/1.5 sec. With 18 options depending on the camera model. Users can choose a suitable shutter speed according to the environmental illumination. Click on < √ > to confirm the new setting. 11.2.
11.3. Picture Adjustment Display of the Picture Adjustment pull-down menu: Brightness: The users can adjust the image’s brightness by adjusting the item. Please select a number from the range of -12 to +13. To increase the video brightness, select a bigger number. Click on < √ > to confirm the new setting. Sharpness: Increasing the sharpness level can make the image look sharper. Please select a number from the range of +0 to +15. This function especially enhances the object’s edges.
11.6. WDR Function The Wide Dynamic Range (WDR) function is for solving high contrast or changing light issues to improve the video display. The WDR is adjustable from Low, Mid to Hi. A higher level of WDR represents a wider dynamic range, so that the IP Camera can catch a greater scale of brightness. Click on < √ > to confirm the new setting. 11.7. Noise Reduction The IP Camera provides multiple options for delivering an optimised image quality especially in extra low-light conditions.
12. Logout When you press the “Logout” tab at the top of the page, the login window will pop up. This permits login with another user name. 13. CMS Software Introduction The Central Management System (CMS) software bundles IP cameras and analogue cameras that are connected to the network via the Video Server into one system. Offering powerful functionalities via intuitive interface, it is a centralised monitoring solution for your video surveillance equipments.
14. Internet Security Settings If the ActiveX control installation is blocked, please either set the Internet security level to default or change ActiveX controls and plug-in settings. Internet Security Level : Default Step 1: Start the Internet Explorer. Step 2: Select from the main menu of the browser. Then click on . Step 3: Click on the tab, and select .
Step 4: Down the page, click on “Default level…” and then click “OK” to confirm the setting. Close the browser window, and open a new one later when accessing the IP Camera. ActiveX Controls and Plug-in Settings : Step 1~3: Please refer to the previous section above. Step 4: Down the page, click on “Custom level…” (see the picture below) to change ActiveX controls and plug-in settings.
The Security Settings screen is displayed as shown below: Step 5: Under “ActiveX controls and plug-ins”, set ALL items (as listed below) to or . Please note that the items may vary depending on the Internet Explorer version you are using. ActiveX controls and plug-in settings: 1. Allow previously unused ActiveX controls to run without prompt 2. Allow Scriptlets 3. Automatic prompting for ActiveX controls 4. Binary and script behaviors 5.
15. GRUNDIG Viewer Download Procedure The procedure of the GRUNDIG Viewer software download is specified as follows: Step 1: In the GRUNDIG Viewer installation page, click “Next” to start the installation. Step 2: Setup starts. Please wait for a while until the loading bar runs out.
Step 3: Click on “Finish” to close the GRUNDIG Viewer installation page. Then, the IP Camera’s Home page will be displayed as follows: NOTE: Please note that the function buttons may vary depending on the camera model.
16. Install UPnP Components Please follow the instructions below to install UPnP components. (The procedure is for Windows XP, for other systems please refer to the corresponding manuals.) Step 1: Go to “Start”, click on “Control Panel”, and then double-click on “Add or Remove Programs”. Step 2: Click on “Add/Remove Windows Components” in the Add or Remove Programs page.
Step 3: Select “Networking Services” from the Components list in the Windows Components Wizard window, and then click on “Details”. Step 4: Select “UPnP User Interface” in the Networking Services’ subcomponents list and then click on “OK”. Step 5: Click on “Next” in the Windows Components Wizard page.
Step 6: Click on “Finish” to complete the installation. 17. Deleting the Existing GRUNDIG Viewer Users who have installed the GRUNDIG Viewer for 1.3 Megapixel Series IP Cameras on the PC need to delete the existing GRUNDIG Viewer first from the PC before accessing this IP Camera. Deleting the GRUNDIG Viewer : Click on “Control Panel”, and then click on “Add or Remove Programs”.
STEP 1: Click on the “Tools” tab and select the option “Internet Options”. STEP 2: Click on “Delete” in the first pop-up window. Then tap “Delete Files” in the “Temporary Internet files” section in the next pop-up window.
Specifications GCI-K1812W Image Sensor 1/2.7" CMOS Omnivision, 2 Megapixel Pixels - Total 1920(H) x 1080(V) Sensitivity Colour 0.6 Lux@F1.5(IRE50), 0.1 Lux@F1.5(IRE30) Lens Focal Length 4 mm Viewing Angle 78° Motion Detection On/ Off/ Sensitivity/ Area setting Privacy zones 5 zones, rectangle White Balance ATW, AWB, Manual Shutter Speed 1 sec to 1/10,000 sec Web Browser MS Internet Explorer 6.
English 75
EC Declaration of Conformity GCI-K1812W 2 Megapixel Full HD Flat Fixed Dome IPCamera 4mm Soft D/N It is hereby certified that the products meet the standards in the following relevant provisions: EC EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC Applied harmonised standards and technical specifications: Measurement Procedure EMI: AS/NZS CISPR 22: 2006, EN55022 CLASS A: 2006 + A1: 2007 EN61000-3-2: 2006 + A2: 2009, EN61000-3-3: 2008 Measurement Procedure EMS: AS/NZS CISPR 22: 2006, EN 50130-4:
