Submittal Sheet
GL-3.14
PROJECT INFORMATION APPROVAL STAMP
Project:
q
Approved
Address:
q
Approved as noted
Contractor:
q
Not approved
Engineer: Remarks:
Submittal Date:
Notes 1:
Notes 2:
FITTINGS FOR GROOVED-END PIPE
C to E
C to E
O.D.
C to E
C to E
O.D.
q
FIG. 7060
Tee
Cast Fabricated
All are Fabricated Steel.
See Fitting Size chart on page 59 for O.D.
q
FIG. 7076
Gr x Thd
Concentric Reducers
Nominal
Size
End
to End
Approx.
Wt. Ea.
In./DN(mm) In./mm Lbs./Kg
1
1
⁄2 x 1 2
1
⁄2 0.6
40 x 25 6 4 0.3
2 x
3
⁄4 2
1
⁄2 1.0
50 x 80 64 0.5
2 x 1 2
1
⁄2 0.8
50 x 25 64 0.4
2 x 1
1
⁄4 2
1
⁄2 1.3
50 x 32 64 0.6
2 x 1
1
⁄2 2
1
⁄2 1.3
50 x 40 64 0.6
2
1
⁄2 x 1 2
1
⁄2 1.0
65 x 25 64 0.5
2
1
⁄2 x 1
1
⁄4 2
1
⁄2 1.0
65 x 32 64 0.5
2
1
⁄2 x 1
1
⁄2 2
1
⁄2 1.3
65 x 40 64 0.6
2
1
⁄2 x 2 2
1
⁄2 1.2
65 x 50 64 0.5
3 x
3
⁄4 2
1
⁄2 1.2
80 x 80 64 0.5
3 x 1 2
1
⁄2 1.2
80 x 25 64 0.5
3 x 1
1
⁄2 2
1
⁄2 1.3
80 x 40 64 0.6
3 x 2 2
1
⁄2 1.3
80 x 50 64 0.6
3 x 2
1
⁄2 2
1
⁄2 1.5
80 x 65 64 0.7
E to E
O.D.
FIGURE 7076 CONCENTRIC REDUCER– GROOVE BY THREAD
Nominal
Size
End
to End
Approx.
Wt. Ea.
In./DN(mm) In./mm Lbs./Kg
3
1
⁄2 x 3 3 1.8
90 x 80 76 0.8
4 x 1 3 2.2
100 x 25 76 1.0
4 x 1
1
⁄2 3 2.3
100 x 40 76 1.0
4 x 2 3 2.3
100 x 50 76 1.0
4 x 2
1
⁄2 3 2.3
100 x 65 76 1.0
4 x 3 3 2.6
100 x 80 76 1.2
4 x 3
1
⁄2 3 2.5
100 x 90 76 1.1
5 x 4 3
1
⁄2 4.5
125 x 100 89 2.0
6 x 1 4 6.0
150 x 25 102 2.7
6 x 2 4 6.0
150 x 50 102 2.7
6 x 3 4 6.0
150 x 80 102 2.7
6 x 4 4 5.9
150 x 100 102 2.7
6 x 5 4 5.8
150 x 125 102 2.6
FIGURE 7060 TEE
Nominal
Size
O.D.
Center
to End
Approx.
Wt. Ea.
In./DN(mm) In./mm In./mm Lbs./Kg
1 1.315 2
1
⁄4 C 0.9
25 33.4 57 0.4
1
1
⁄4 1.660 2
3
⁄4 C 1.5
32 42.2 70 0.7
1
1
⁄2 1.900 2
3
⁄4 C 1.8
40 48.3 70 0.8
2 2.375 3
1
⁄4 C 2.4
50 60.3 83 1.1
2
1
⁄2 2.875 3
3
⁄4 C 4.0
65 73.0 95 1.8
3 O.D. 2.996 4 C 4.6
76.1 76.1 101 2.1
3 3.500 4
1
⁄4 C 5.8
80 88.9 108 2.6
3
1
⁄2 4.000 4
1
⁄2 C 9.8
90 101.6 114 4.4
4
1
⁄4 O.D. 4.250 4
3
⁄4 C 9.3
108.0 108.0 121 4.2
4 4.500 5 C 10.3
100 114.3 127 4.7
5
1
⁄4 O.D. 5.236 5
1
⁄4 C 14.1
133.0 133.0 133 6.4
5
1
⁄2 O.D. 5.500 5
1
⁄2 C 16.1
139.7 139.7 140 7.3
5 5.563 5
1
⁄2 C 16.2
125 141.3 140 7.3
6
1
⁄4 O.D. 6.259 6 C 20.8
159.0 159.0 152 9.4
6
1
⁄2 O.D. 6.500 6
1
⁄2 C 24.4
165.1 165.1 165 11.1
6 6.625 6
1
⁄2 C 25.7
150 168.3 165 11.7
8 8.625 7
3
⁄4 C 41.1
200 219.1 197 18.6
10 10.750 9 C 74.5
250 273.1 229 33.8
12 12.750 10 C 94.7
300 323.9 254 43.0
14 14.000 11 118.0
350 355.6 279 53.5
16 16.000 12 146.0
400 406.4 305 66.2
18 18.000 15
1
⁄2 218.0
450 457.2 394 98.9
20 20.000 17
1
⁄4 275.0
500 508.0 438 125
24 24.000 20 379.0
600 609.6 508 172
For Listings/Approval Details and Limitations,
visit our website at www.anvilintl.com or
contact an Anvil
®
Sales Representative.
C - Cast ductile iron, all others are fabricated steel.
See Fitting Size chart on page 59 for O.D.