HOME 7500 User Guide www.americanbst.
SDoC statement This publication provides instructions for installing Cellular Signal Booster Home 7500. Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: HOME 7500 Responsible Party – U.S. Contact Information Copyright© 2019, American Booster Inc. All Rights Reserved. FCC Compliance Statement (e.g., products subject to Part 15) This device complies with Part 15 of the FCC Rules.
WARRANTY Opening or tampering with the Signal Booster will void all warranties. INDEX American Booster provides a 2-year warranty with all of its equipment. Every product of American Booster is guaranteed to be free of material defects or component malfunctions. This warranty does not cover any Signal Boosters that have been exposed to any misuse, abuse, Product Introduction 4 physical damage or inadequate maintenance.
HOME 7500 IC Warning Statements RSS-GEN, Sec. 7.1.2 – (transmitters) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
FCC Warning Statements Package Contents FCC Part 15.105 statement Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Application Application Example Example Safety Guidelines WARNING ELECTRIC SHOCK Opening the Signal Booster could result in electric shock and may cause severe injury. DAMAGE TO EQUIPMENT Use only the power supply provided in this package. Operating the Signal Booster with antennas in very close proximity facing each other could lead to a severe damage to the Signal Booster.
HOME 7500 Optional Kit Specifications Parameter Downlink 700MHz LTE 734~757MHz 850MHz Cellullar 1900MHz PCS 2100MHz AWS Composite Power Maximum Gain Noise Figure Impedance RF Connector Power Connector Power Size, inch Weight, lbs Operation Temperature Humidity 869~894MHz 1930~1990MHz 2110~2155MHz 7dBm Uplink Remark 704~716MHz 776~787MHz 824~849MHz 1850~1910MHz 1700~1755MHz 25dBm Band 17 & 13 Band 17 Band 5 Band 25 Band 4 70dB 5dB nominal 50 Ohm SMA Female DC Jack(DC-045B) DC 12V/3A Adaptor 6.
Installation Guide Troubleshooting Instructions to fix flashing or solid red. STEP 1. Find the Strongest Signal If you have a good voice signal and fast data speeds even though one or two of LEDs are solid red, you may continue to use the Signal Booster as it is. However, if one of the LED’s has flashing or solid red, your voice signal is weak and data speeds are low, Then follow the troubleshooting steps below. 1-1. Using an iPhone Dial *3001#12345#*, then press Call. 1-2.
HOME 7500 LED LED Indicators STEP 1. Find the Strongest Signal Note The stronger signal you receive from the base station, the better coverage you will have inside your house/office. -70dBm Flashing Green After the Signal Booster is powered on, flashing green will last for 20 seconds. It means that the Signal Booster is being set up for optimal performance. The Signal Booster will need a few minutes to adapt to the network environment and start boosting the signal at the highest power.
STEP 2. Install the Outside Antenna STEP 6. Power up the Booster The outside antenna is shaped like a triangle. This antenna must be mounted as high as possible on the exterior of the house or office. Mount the outside antenna on the side of the house where you detected the strongest cell phone signal.
STEP 5. Install the Signal Booster Choose a location for the signal booster, preferably away from excessive heat, direct sunlight, moisture and free from high temperatures. Do not place the signal booster in an air-tight enclosure. Attic installations may expose the booster to high heat. STEP 2. Install the Outside Antenna Install the outside antenna in a location where you can receive the strongest signal according to the instructions described in STEP 1.
STEP 3. Run the Outside Antenna Cable When mounting the outside antenna to the outside wall of your building, the easiest way is to run the cable on the outside of the wall and attach it to the exterior of your house or office. STEP 4. Install the Inside Antenna Inside Panel Antenna is directional, so the signal will be distributed from its front side in one direction. We would not recommend to install the Inside Antenna close to the floor.
