V6 Vehicle intelligent Balance Charger AD TOO J DO 200W 7144 EO ROWE RICE Ass ir AD Mag FS Gh EE tare TA Thank you for: merchandising: GT: Power: V6: AC DC intelligent. charger/ discharge: This is a rapid. chargsi/discharger with built-in. microprocessor and brand new: program.
10. Warranty end Service... Contents Specification... Exterior of the unit Warnings and safety notes... How to Confirm Charging Current... Charging Mods Selection Program Setting Showing Screen . System Ratting Alarm and Error Information ..
E, Exterior of the Unit 3 IPS Display #3 DC input port £3 Select key u £3 Upgrade port €3 AC Input port {3 Battery Interface €} Balance lead socks Select key Long press: Enter Ina system setting/ terminate the current teak Short press: Enter into system setting/ confirm the current setting Scroll uo and down; Select menu
ERT CE [iT Never leave the charger unsupervised when it is connected to a paws ‘source, or during charging. If any nor or malfunction is observed at any point Immediately terminate the process and refer to this Instruction manual Keep the charger away from dust, dampener, heat, direct sunlight and vibration. Do not drop it. The power is designed to be powered by a 100-240V AC supply or 10-24 DC supply only.
compact final discharge voltage The final discharge voltage should not lower than lithium battery's minimum voltage, this will cause battery capacity lows or permanent damage the battery Generally, vou do not need to discharge thallium battery voluntary.
4. How to Confirm Cal Current It Is necessary to know the max. Charging current before charge due to excessive current could shorten the life span of the battery, even do permanent damage ta the battery. Excessive charging current may possible cause fire or explosion during charging. The charging and discharging capacity of the battery is usually marked by C Value, C value multiply the battery capacity is the maximum battery charging current.
The working mode of the charger Is series charging, It must connect to the battery output cable when connect ta the battery. For the Lithium battery, you should connect the balance port ta enter the balance charging mode. Through this can monitor the voltage of sate call and balance the ans which voltage Is Inconsistency.
charging The inner system will monitor each cell's voltage an control the current of each cell then to balance the individual cell voltage. You need connect the battery to the output cord as well as the balance port when charging Battery fast charge mods The charge current will get smaller and smaller till charge finished. The fast charge program will finish charge In advance and decrease the CV and balance process.
voltage of the battery should not lower than Tts lowest voltage dus to It will cause capacity rapid loss Normally, there Is no necessary to discharges Illumine battery. For safety reason, discharge current displayed on screen should not exceed the rated max. discharge current, and the rated voltage can not lawyer than the voltage level recommended by cell manufacturer to avoid over discharging.
Connect the charger to the power supply and wait for the charger to finish eff testing. Connect the battery to the charger under standby Interface, and shirty press the & Cell count 2s select key to show the program &) Curt sating O1A setting menu as below; Start mode € Back Proliferate lion. LIF DOMINIC. PD ‘Balance Charge. Dame. Fast Charge: Discharge: Stores: Re par: Goddammit | Li Xx battery | Boris, NIMH/ANIGD 1: abseils PB 121 unis Charge current © 1744 Discharge currant 0 1.
Scroll select key up and down to switch screen information, in order of ens cell's voltage and working parameters Fast balance chars status: Working status Balance Charging Input Volley/ Power <= 11 SAFAVID fr 1 79th = > Tosloupxteneny oes power Output VotisgelPowsr 59 BY/OORLY 1 Opes o> Fried chagrin es ae power Working temperature «= (8) 70°C fps = Ped dud kg Ines 2
LE XX battery IR Test: The charger have the IR teasing function and tt wil Just work when balance charging It wil test and calculates the IR value after charging 2 minutes later. ft cannot be realized to measure the absolute value as professional internal resistance tester does. Therefore, the internal resistance value can ably ba strafed to when conducting horizontal comparisons, such as Judging the consistency of the cells’ performance or making comparisons af the performance of die rent cells.
tums Into Blue. The charger should continue to cray out accurate balancing of the battery after the light turns Blue. After the charging finished, it is normal far voltage decline to occur dus to different performances. As the number of the charge cycle grows, the performance decreases, and the voltage decline phenomenon becomes obvious. To charge tha battery with e larger current would also cuss a more obvious voltage decline after the charging fished.
IRE ETE TERR Long press select key under system stand by status to set the menu. Mae. inp Power so pain MI input Vortexes: 1020V Back Sheathes High, madding, low and alight Volume High, medium, low and tum off 2 kinda: once ard repeatedly. 7 agelessness, Including English, Chines sic Checking the system Information ‘System serif checking Without connecting to battery Hank to ast Men Mex. Input power limitations ‘When the input power failed to reach the max. working PowerPoint.
used as the input power source, the value of the fem should ba 21V to protect the battery from excessive discharge Buzzer volume When it setting to OFF, the operation sound would be OFF, but the sound of error warning will keep ta ON REE ib hone £1 Min Input Voltage 100Y.
TT It combines with various protective functions and mentor systems to verify ts electronics functions and status. The screen will display the smog Instructions: with & waning sound If anything works wrong. 1. Battery type select error! Battery type select emir. Charger will select the battery type as the same 88 the real battery type again 2{ Battery not connected | 7} Battery do not connected charger pie ass check the connection cables. 3.