& Bela aed FETCHER nae 2) thy bile in tre wearer servomechanisms Esther un effusion ® Battery repairing function Thank you for purchasing the balance charger. This Is a rapt charger/discharger with builtin balance, computerized with microprocessor and can support scan QR code charging and phone APP control. Please read the entire operating manual completely and attentively before using.
[Optimized operating software] “This unk can automatically asst current according ta the change of the charging rive and battery voltage when charging or discharging. t can avoid battery explosion due to user's inappropriate. operation especially when charging LUX batteries This charger provide balance port for thrum batteries slut for 2-6 cells. [High Ewer and High Performance Reuters] “This charger’s maximum output power Is 300W, maximum charging current is 124, maximum discharging current Is 3A.
Temperature limit: The Inner temperature will rise when charging When set « mad mum ‘temperature the charging program wil be forced to end when charging temperature exceed the setting value This function nee! to connect exterior temperature sensor. Charge time limit: You can through restrain the charge time to prevent any possible aver charge/discharge. Input voltage checking: To protect battery, program will automatically shut down the charging current when the voltage decreased to the lowest.
+ Never leave the charger unsupervised when Its connected to power any malfunction happens, terminate the program Immediately and refer to the operation manual for the right operation. + Keep the unit away from dust, damp, rain, heat, direct sunshine and ration. Do not drop it. “Th unit cuttings designed by 11-26V for DC Disputant 100-240V for AC Input only.
Yau have to know the battery allowable maximum charging current before: charglg. Charging current exceeds the allowable mods an charging current may cause damage to battery and tis possible to lead afire and explosion of battery when charging. ‘We usually use C value to mark battery charging/discharging capability The battery allowable maximum charging current is calculated by multiply C value by bear cap achy.
7.1 Lithium battery balance charge meed This I for balancing the voltages of Lithium bagatelles of the battery pack ta be fully charged. Ines system will monitor each cel voltage and restraint each clefs current to fulfill Balance changing. You need to connect the battery to the charger’s output plug as wel as the balance port when charging. ‘The second ine eft side to set charge current value, right dido sat the battery pack voltage value.
“The second line left side to set discharge current value, right side to set the battery pack voltage value. Afr done, press. and hold Start/Enter for 3 seconds to start the program. {discharge ell voltage: 1~calls) it shows the current discharging status, Press Bats type/Stop to stop discharge. 7.
7.5 Li Po FE.DIS mode You have to use this mode under DC working status and Input port connected to battery, ‘otherwise wil report an retro. BF-DIS working principle Is transmit the standby discharging battery capacity to Input battery through the charges and achieved the discharge effect.
It shows the current charging status, press Bart type/Stop to stop charge. Its haws each battery pack single cell voltage. Its designed for charging and discharging NIGH or Nice battery that commonly used for RIC model. The screen tums bright when press Start/Enter, then you can press DEC/INC to change the parameter va pressures Stan/Enter to store ww} = omen 2.1 Charge Nicodemus battery The second Ine let side to set charge current value, it shew to settee battery pack voltage value.
£3 NIGH /NKd battery charge and discharge cycling mess Set the sequence on the left and the number of cycle {1-5) on the Eight You can use this function to balance and refresh or cut off battery.To avoid battery temperature rising, there Will se a brief cackling process after each charge and discharge cycle. In this process, press “Bart type /stop" to stop the program. Press Testamentary for 2 seconds fo start the program.
discharge. For your safety, the discharge cutest value displayed on the screen should not cede the mad mum discharge current speckled by the battery manufacturer, and the rated voltage should not be lower than the voltage level recommended by the battery manufacturer to avoid deep discharge, Select discharge battery types and voltage correctly. Seth charge current value on the second Ine eft side, sex the battery pack voltage on the right ski.
Set discharge current on the left side and nominal voltage on the right. Press Start /Enter for 3 seconds to start the discharging process. battery voltage: 1-107) 2.2 Ph battery DIS BF-DIS can ony be operated when the better is connected to the input interface under DC. made, otherwise wil report err. The FADDISH mode k to transfer the capacity of the battery robe discharged to the input battery through the charger to achieve the purpose of discharge.
CIPRO Charger Is the Intelligent functionalism charger. ft can charge many different battery types and can alas charge DJ batteries. a: wr} dr 10.1 DJ Phantom 5 battery charge program “The battery's capacity of Phantom 3 professional and Phantom 3 5 4480mAh and the standard voltage s 15.2Y, 1t15 asy to operate the charger ta charge the DJl batteries. Connect the battery and press Start/Enter aver 3 seconds fo start the program and press Bart type/Stop to stop the charge.
Press STATUS key to show the highest/lowest voltage of the single cell and the total voltage of the battery pack. Enliven battery infernal resistance is ane of the important index of battery discharge ‘capability and efficiency. We can knew battery performance and the matching of each battery by getting the battery IR value. The value more smaller the higher matching degree between the batteries. The charger detected battery IR value Is Is relative value not ‘absolute value.
Bm ben We've added some extra functions for Hero, such as motor-run, digital power, tre warmer, PWM test ste. 13.1 Motor run introduction This program alms to test the quality of DC two-phase motor and check the quality of motor. Set the motors Input parer, check its output current and power, tasted with certain test ‘equipment te Judge the motor using status and quality.
Short press Star/Enter to star the program, through press INCIDENCE to set heating temperature, heating ime, heating rs power. Ter Heating temperature heating time 1-120 minutes, wre amo heating power 10-106W, After fished, long press ENTER to test Interface. [need re-set parameters short press STOP back to set interface. 13.4 PWM IN introduction “This program can be used 10 test the pulse width value of ‘other equipment.
“This charger can save setting data of each program, It can save 5 groups data for each kind of battery, Including the ces of the battery, setting charge current and so on. Users da not need to set the data again when they use the batteries which have been memory. tis Easter and more convenient ta use, ‘Select memory mode, press Start to start set. Press STATUS to choose the number. Press START 2 choose battery type.
EH my | SNEERING. Sn wed Lip Git off voltage rang Is we'd suggest uses set cut off voltage to 4.2, to avoid exceed battery maxima charging voltage causing damage t battery and your property. Lib cut off voltage range is we'd suggest user se cut off voltage to 435V, to avoid exceed battery maximum charging voltage causing damage to bestiary and your Progeny.
charging after the fast charging Is over to avoid battery overheating. If you tum an safety timer when charging, safety timer wil Start timing tom system fault of system can't plenty battery ‘capacity already ful, this safety time set can stop battery any being over charged The safety the should not shorter than the battery fully charged time. Cap achy cut-off program set the maximum charging ‘pate.
“This unit with builtin high speed Bluetooth module.you can connect ape through Bluetooth ‘and set nonchargeable parameters an app, such as safety time, temperature protection, lama sound ono, capacity protection, low voltage protection and fin ware upgrade etc. it also support scan QR aced to charge.
It combines a varlet of protection functions and wondering systems to identify ts electronic functions and status, Screen will automatically display the nor reason with a prompt tone Hf any error happens. 1. REVERSE POLARITY *} Battery output Polarity connection Wong; 2.0 CONNECTION BREAK} Interruption of battery and output, or the charger wire Is not connected well when ‘operate the charge or discouragement. 3.07 OUTPUT SHORT CIRCUIT") Short-circuit of the output terminal. Ease: check the charger wire 4.
