GT 970 INSTALLATION AND USER MANUAL Getronic S.r.l. Via Calcinate No. 12 21026 Gavirate (VA) Italy Tel. +39 0332 756011 Fax + 39 0332 731162 www.gtalarm.it InstManGT970-UKRev07.
SUMMARY 1.0 - GENERAL DESCRIPTION 2.0 - INSTALLATION AND CONNECTIONS 3.0 - CONNECTION DIAGRAM 4.0 - ALARM POSITIONING 5.0 - SET FUNCTIONS 6.0 - USER MANUAL 7.0 - MAINTENANCE AND WARNINGS 8.0 - COMPLIANCE DECLARATION 9.0 - TECHNICAL DATA 10.0 - WARRANTY CONDITIONS Page Page Page Page Page Page Page Page Page Page 2 2 3 4 4 7 10 11 11 12 1.
- Connect the BROWN wire (power supply negative) to the negative terminal of the vehicle’s battery - Connect the RED wire (12V positive power supply) to the positive terminal of the vehicle’s battery using the 3A fuse. - Connect the RED/WHITE wire (indicators 12V positive) to the positive terminal of the vehicle’s battery using the 15A fuse. - Connect the wire GREEN wire to the motor vehicle seat/bonnet/sidestand switch.
.0 - ALARM POSITIONING The system is equipped with a “SENSOR” which allows to detect possible motor vehicle shocks/ movement. For an optimum operation pay attention to the fixing positions indicated below. WARNING: - Before carrying out the definitive fixing it is suggested to place temporary the alarm and check the correct operation of the shocks/movement sensor. YES YES YES YES HORIZONTAL PLANE YES YES YES YES HORIZONTAL PLANE NO NO YES MAX 10° HORIZONTAL PLANE 5.
To come out from the SET FUNCTIONS: Wait the end of the signal and place the GT889 handsets contacts to the receptacle (not during the Function No. 3 - HANDSETS SELF-CODING). The exit is confirmed by the Led switching off and by 5 beeps. In the “FUNCTIONS TABLE” are mentioned the functions which can be selected. SELF-CODING emergency procedure. In case of GT889 handset-electronic key loss it is possible to enter the SET FUNCTIONS: A - With the alarm disarmed disconnect the power supply and wait 1 minute.
- HANDSETS SELF-CODING (Function No.3). With the function No. 3 it is possible to self-code new handsets to the control unit up to a max. of 8. 1 - Select the function and press the “ON” button to be self-coded. 2 - The system confirm the correct handset self-coding by a flash of the GREEN LED and by a beep. WARNING: - When you have entered the function the first handset which is self-coded deletes all the other handsets memorised.
6.0 - USER MANUAL - HANDSET DESCRIPTION. GT889 GT884 (Opzional) LED GT889: 3 buttons with electronic key incorporated. LED ON GT884N: multifunction button (Optional). It integrates a sensor which keeps the “LINK” transmission active. If the sensor doesn’t detect vibrations for more than 2 minutes, it reduces the transmissions and so the battery consumption. Note: avoid falls and shocks to not damage the sensor. -Button: to arm and disarm the alarm system.
- EMERGENCYDISARMING. In case of emergency (i.e. handset low battery) it is possible to disarm the system placing on the RECEPTACLE the electronic key integrated in the GT889 handset. - IN CASE OF ALARM. - Pressing the “OFF” handset button or approach with the handset in AUTOMATIC-TRANSMISSIONLINK mode” to disarm the system. Note: it is possible to stop the alarm without disarming the system pressing the ON GT889 handset button. - PRE-ALARM BY LINK.
5 - Release the "OFF" button and close the remote control handset. 6 - To change the function state repeat the procedure from the point 1 (at each repetition of the procedure the function changes state). - PROTECTIONS. When the system is armed the status check LED switches constant on, after 30 seconds the LED flashes. The ignition key, seat/bonnet/sidestand and wires cut protections are active 5 seconds after the arming, while the shocks/movement sensor is active when the status check LED flashes.
ANOMALIES SIGNALS TABLE ALARMS SIGNALS TABLES Status check LED flashes number Input which has generated the alarm RED PAUSE SHOCKS/MOVEMENT SENSOR PAUSE SEAT or BONNET or SIDESTAND 2 RED 5 Status check LED flashes number Cause which has generated the anomaly RED/GREEN HANDSETS BATTERY SYSTEM STATE TABLE LED Colour RED 6 PAUSE State RED MOTORCYCLE INSTRUMENT PANEL SYSTEM IN PHASE OF ARMING Constant on ROSSO RED 7 PAUSE ARMED SYSTEM WIRES CUT Slow flash LEGEND: COLOUR N N = Flashe
- HOW TO REPLACE THE HANDSETS BATTERY. \ WARNING: the batteries selling off has to always occur in appropriate way and it has to be in compliance with the local rules in force. - With care lever the front case for the printed circuit LED Li Li WARNING! - The battery negative terminal has to be pointed upwards (with components) and the positive downwards (handset bottom). Replace with a Lithium battery Mod. CR2032 (3V) for GT889 Mod.
This Certificate should be kept in a safe place and produced for verification should technical assistance be required. Inability to produce this Certificate may affect your warranty rights. Warranty period bengins from date of purchase and is valid for 24 months. Should technical assistance be required during the warranty period, you should take your vehicle and this Certificate to either the original installer or the nearest GT Auto Alarm Service Centre for inspection.