User's Manual
SENSE INPUT
SENSE POWER
M1–+ M2
Closed Open
GND
SENSE
Gate Edge
Controller
DC Operator
LEARN 1 LEARN 2
3.3V
GND
The pushbutton labeled LEARN 2 is used to program transmitters to channel two. Momentarily press the receiver’s program button. The
red programming LED will light. The LED slowly blinks
for about 60 seconds. A transmitter must be entered
while the LED is on. Press the desired learn button. The
LED will flicker indicating that the receiver has accepted
the transmitter and channel relay will toggle.
NOTE: Be sure to press the receiver program button
for less than 2 seconds.
Be sure gate area is clear. Test the units by activating the gate and touching the
edge sensor to ensure the gate obstructs.
Transmitters may be erased from the receiver’s memory by pressing and holding
the receiver’s program button until the LED blinks one time as the receiver’s
memory is erased. Then release the program button.
This Linear PRO Access (LPA) product is warranted against defects in material
and workmanship for twelve (12) months. The Warranty Expiration Date is labeled
on the product. This warranty extends only to wholesale customers who buy direct
from LPA or through LPA’s normal distribution channels. LPA does not warrant
this product to consumers. Consumers should inquire from their selling dealer as
to the nature of the dealer’s warranty, if any. There are no obligations or liabilities
on the part of LPA for consequential damages arising out of or in connection with
use or performance of this product or other indirect damages with respect to loss
of property, revenue, or profit, or cost of removal, installation, or re-installation.
All implied warranties, including implied warranties for merchantability and implied
warranties for fitness, are valid only until Warranty Expiration Date as labeled on
the product. This LPA Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact LPA Technical Services at 1-800-543-1236 for an
RPA# and other important details
Linear PRO Access radio controls provide a reliable communications link and fill an
important need in portable wireless signaling. However, there are some limitations
which must be observed.
PRINTERS INSTRUCTIONS
INSTR,INSTL,SGER SERIES - GTO P/N: 10016916 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 2 of 2
LEARN 1 LEARN 2
CHANNEL TWO
PUSHBUTTON
USE THIS
PUSHBUTTON
TO ENTER A
TRANSMITTER
INTO CHANNEL
TWO
LEARN 2
LEARN 1
S2
PRESS THE TRANSITTER
BUTTON ON THE CONTROL
BOARD
PRESS THE LEARN
BUTTON FOR THE
DESIRED CHANNEL
(LEARN 1 or LEARN 2)
THE LED WILL
LIGHT AND REMAIN
ON ABOUT FIVE
SECONDS
RECEIVER LED WILL FLICKER
AS TRANSMITTER IS ENTERED
INTO MEMORY
LEARN 1
LEARN 2
LED WILL FLASH, COUNTING
THE TOTAL NUMBER OF
TRANSMITTERS PROGRAMMED.
THEN IT WILL BLINK ONCE
(CHANNEL ONE) OR TWICE
(CHANNEL TWO) AS THE
TRANSMITTERS ARE ERASED.
PRESS PROGRAM BUTTON FOR
FIVE SECONDS OR MORE
STEP 6b Connect antenna STEP 7 Program the receiver
STEP 8 Test receiver INFO 1 Erasing receiver memory Troubleshooting
LIMITED WARRANTY IMPORTANT
TOUCH THE EDGE
SENSOR TO ENSURE
THE GATE OBSTRUCTS
WARNING: BE SURE GATE AREA IS
CLEAR OF OBSTRUCTIONS
Copyright
©
2017 GTO Access Systems, LLC
Document Number: 10016916 REV A (05-15-17)
SGER Alarm Fault? Condition
Code
Low Batt 1 NO Low Battery
Open 2 YES No resistance across TB1 and TB2 of SGET
No Ack 3 YES SGET not able to send message
(dead or too far away)
Edge 4 YES Edge shorted
DC Operator Wiring
NOTE: For AC Operator install an AC
Sensor, and refer to the AC Sense
instructions book.
WARNING: Changes, modications or adjustments not expressly approved by GTO
Access Systems, LLC could void the user’s authority to operate this equipment.
There Are No User Serviceable Parts.
NOTICE: This device complies with part 15 of the FCC rules and with Industry
Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation
of the device
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.