Installation Instructions

fingerprint reader
Touch Keypad
Base plate
latch
CORRECT
INCORRECT 2
3
4
(70mm)
2
3
8
(60mm)
Adjust the backset, it is and
2
3
4
(70mm)
2
3
8
(60mm)
2，Restore factory settings
a,Press and hold the reset button for a long time, and two "drops" will be heard. The lock will be restored to the factory settings. After the
system is cleared, all the passwords added before and the phone administrator will be invalid
b,When app is added to the lock, you can delete the administrat of this lock in APP (click Settings - click delete). Note: after deleting the
administrator on the app, the lock will be restored to the factory settings, and all previously added passwords and mobile administrator will
be invalid;
Ⅲ:Operation instructions
1,Feature:
a,Password length 6-12 bits;
b, the factory status code 123456# can open the door
c,Password anti peeping function: you can add some irrelevant codes before and after the password, and then press
#
confirm (the maximum length
is 15 digits). you can enter the password as follows: XXX password XXX #
d,Low voltage prompt function: touch and light the panel when the battery voltage is lower than 4.8V, and the backlight on the screen flashes
quickly 1 second. password is unlocked, the backlight on the screen will flash quickly for 1 second, and then unlock again
e，When using APP to operate the door lock, most of the function operations need to be operated beside the door lock .
f，The registered user for password, fingerprint on the door lock need to use the upload function in the app to see and edit them in the
app
g,Password input error protection function: the system will lock the password keyboard when the unlock password is input wrong 5 times in a row,
and automatically unlock it after 5 minutes. During locking, app can unlock the keyboard.
3，Add administrator password (administrator can only be password, fingerprint and card cannot be added as administrator)
a,When the lock is in the factory state and the app is not registered:
b,After the lock is restored to the factory settings, the system will automatically generate an administrator password after the mobile app
adds the lock, which can be revised in the app
4，Add user fingerprint, password
(Can be added continuously)
,users who are not added through the app need to use the upload function in the
app to display）
a,
b,If the lock is registered in the app, just Add fingerprint, password in the app
5,Change administrator password
a,
b,On the app, select this lock name - > Settings - > administrator unlock password - > enter the new administrator password.

7，Delete (the door lock operation cannot delete a single user alone, and the app can delete a single user)
a,Delete all passwords (except administrator):
：
b,Delete all fingerprints:
c,Add an app to delete a single user in the app

Ⅳ：Note !
1，Although the door lock is treated with simple waterproof treatment, it cannot be installed outdoors that can get wet, so as to avoid damage
caused by water entering into the line
2, The door lock does not have fire protection function and is not suitable to be installed on the fire door
3，Do not use inferior batteries to avoid battery leakage damaging the power supply system
4，Please pay attention to the positive and negative poles of the battery when installing the battery
5，Do not use sharp hard objects to scratch the surface of the touch key screen
6，Do not wipe the lock surface with corrosive liquid to avoid damaging the electroplated layer
7，If the administrator password is forgotten, the lock can be reset to the factory status
8，After the door lock has been used for a long time, in order to ensure the flexibility of handle rotation, please remove the door lock and add
lubricating oil to the rotating part inside the handle
Ⅴ：Common problem
1，No electricity
a,Check whether the connectors of the connecting wires of the front and rear plates are connected properly
b,Is the battery installed? Is the battery installed reversely
2，The lock can’t be opened：
a,Whether the password is correct, and whether the card or password or fingerprint has been deleted
b,The door shall be opened within 5 seconds after entering the password and other door opening modes. If the door is not opened, it will return
to the free state
c,Touch the screen to see whether the screen can activate the light
Ⅵ：Specification parameter
-20°C-70
°C
20%
-
93%
33mm-52mm
fingerprint，Password
，APP
APP
带
fingerprint quantity 100
150
*12#
123456
#
new administrator password
#
new administrator password again
#
*85#
administrator password
#
new user password again
#
new user password
#
*12#
old administrator password
#
new administrator password again
#
new administrator password
#
*85#
administrator password
#
Press your finger four times
*85#
administrator password
#
Put the card on the card reading arean
6,
Change the user password (users not added through the app need to use the upload function in the app to display in the app)
a,
b,When the lock is registered in the app, click the password management to open the password to be modified and directly modify it
*10#
old user password
#
new user password again
#
new user password
#
*71#
administrator password
#
*70#
administrator password
#
Power supply
4.5V-6.5V（4 AA battery ）
Quiescent current Less than 40 UA
Dynamic current Less than 250mA
working temperature
relative humidity
Doorthickness
Unlocking method
Password quantity
3，
Fast power consumption
Check whether the battery is of poor quality. Normally, the battery can be used about one year
download the APP
8， Add App for Digital Lock
a，Factory State :When the screen light is off ,User touch the Keypad to wake the Lock and add Bluetooth Administrator before Long Sound “DI”.
b,Adding New Administrator:Although the lock has set an Administrator password or added an APP ,allow other App user to add this lock and become
the new administrator.Let the lock enter the mode where you can add the phone Administrator.
*83#
administrator password
#
USB Charge