User's Manual

11#
USER MANUAL
AGE 8+
ABOUT THE RC CAR
The RC car adopts 2.4G variable speed control technology to control functions such for forward, backward,
left and right turning and multiplayer competition without interference. Pull the Trigger to control the speed.
The harder, the faster, and the slighter, the slower.The design such as powerful motor and antiskid tyres
makes stable driving of the car possible, bringing you an ultimate experience full of speed and thrill!
PREPARATIONS
Charge the Battery for RC Car
STEPS
1. Unscrew the screws on the battery compartment in the car with a screwdriver,take out the battery for charging.
2.Connect one end of the USB charging cable to the battery connector and ensure it is correctly connected. Then
insert the other end of the USB charging cable into safe power supplies with USB socket, such as PC, laptop, mobile
power, or USB power socket etc.The red light turns solid on during charging and goes out when charging completes.
Full charging takes around 3 to 5 hours.
3.After charging, connect the battery with the battery connector and ensure it is correctly connected.
4.
Insert the battery into the battery compartment, refit the battery cover, and finally tighten the screws with a screwdriver.
Juveniles shall be accompanied and guided by their guardians to charge the product.
It is recommended to fully charge the battery to ensure sufficient power before the first use. Please understand
that the running time will be relatively shortened without prior charging for the first use due to insufficient power
of the battery, which is caused by the auto discharge during transportation.
Do not charge batteries that are inflated, leaked or damaged. Do not overcharge the battery.
Please use the original USB charging cable from the factory. Do not use charging cables that are damaged or non-original ones.
Keep it away from flammable materials and do not put it on the surface of conductive objects(such as carpet,
wooden floor or furniture, etc.) during charging.
Please be careful to avoid electric shock while using the electrical products.
NOTICE:
ON/OFF Switch
Forward/ Backward Trigger
Steering Wheel
Indicator Light
ON/OFF Switch
Battery Compartment
Battery Compartment Screw
Rechargeable Battery
Battery Connector
Direction Fine-tuning
BATTERY
RC Car x 1 Remote Controller x 1 Rechargeable Battery x 1 USB Charging Cable x 1
User Manual x1
ACCESSORIES
3.3 Drive in Suitable Environment.
Suitable Driving Environment Unsuitable Driving Environment
Asphalt Pavement/
Cement Pavement/ Hardwood
Gravel / Hill / Snowfield / Desert
5.Turn Left: Rotate the steer wheel
backward to let the RC car turn left.
6. Turn Right: Rotate the steering wheel
forward to let the RC car turn right.
7.Fine-tuning: If the RC car fails to drive in a straight line, toggle fine-
tuning switch to trim the directions from side to side accordingly as to
let the front wheel move forward horizontally.
STEPS
DRIVE VIA REMOTE CONTROL
1.Power on: Turn on the switches
of the RC car and the remote
controller to power them on.
2.Pairing: Turn the Power Switch ON to pair
with the car. The Indicator Light goes off when
pairing is done and the car is ready to run.
Please don’t operate the trigger and hand wheel
of controller until the binding is successful.
3.Forward: Pull the trigger of the
remote controller backward to let
the RC car drive forward.
4.Backward: Push the trigger of the
remote controller forward to let the
RC car drive backward.
MAINTENANCE
1.Keep the RC car in a cool place
after usage and do not touch the
motor until it cools down.
2.Wipe out the sand, muds and
dust on the RC car after usage.
3.Take out the batteries from the RC
car and the remote controller and keep
them in separate places when the RC
car is not in use.
4.Anti-rust oil (not included) can
be applied to protect the exterior
metal against rust.
2.Fail to activate fine-tuning function.
TROUBLE SHOOTING
Problems
RC car fails to drive
in a straight line.
RC car/ remote
controller out of
control/ not
responsive
Close control range.
1.Switch not turned on. 1.Turn on the switch.
2.Ensure the positive and negative terminals are correctly aligned.
3.Replace the batteries of the remote controller/ Recharge the batteries for the RC car.
2.Batteries improperly installed.
3.Low battery voltage.
4.Out of control range.
5.RC car not pair with the remote controller.
Causes Solutions
4.Control it with in 45 meters.
5.Power off the RC car and the remote controller and then turn on again and pair again.
1.Signal interference around.
2.Low battery voltage for RC car/ remote controller.
1.Try to drive in another place.
2.Replace the batteries of the remote controller/ Recharge the batteries for the RC car.
1.Excessive surface friction or extremely smooth surface. 1.Try to drive in another place.
2.Toggle fine-tuning switch to trim the directions.
NOTICE:
Do not use it in conditions like rains and snowstorms etc. to avoid
accidents.
Do not use it on public roads to avoid impacts on the traffic.
Do not use it near crowded places, people or animals to avoid
environmental damage or body injury.
Do not use it in the rain or let the car run over the puddle to avoid
malfunction.
Do not use it near rivers, ponds or lakes to prevent the car from
falling into the water.
STEPS
3.2 Install the Battery for Remote Controller
1.Use a screwdriver to unscrew the screws on the battery
compartment of the remote controller and open the battery cover.
2.Install three new 1.5V AA batteries (not included) into the
battery compartment and make sure the “+” and “-”of the
batteries match with those indicated inside the compartment.
3.Refit the battery cover and tighten the screws.
NOTICE:
Please ensure the “+” and “-” electrodes have
been correctly aligned.
Do not mix old and new batteries.
Do not mix different types of batteries.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
NOTE
7.0