User's Manual

6 7
8
9 10
Reset the Device
You can follow one of the methods below to
reset the device.
Video recording playback:
Tap " " on the APP to playback the video
recordings stored in the TF card.
Snapshot and video recording:
Tap " " or " " on the APP to take a picture
or take a video recording. The pictures or videos
will be saved into the Gallery of your mobile phone.
Basic functions settings:
1. Set the status indicator LED
2. Flip image setting
3. Set the intercom way(simplex/duplex)
Troubleshooting
3. False motion detection alarm keeps
going off.
Check if the PIR is exposed to direct sunlight.
Adjust the sensitivity via the APP. By default, the
sensitivity is set to "Medium".
Visual intercom:
You can monitor the doorbell, intercom with the
visitor, or answer the visitor's call remotely.
Share the device:
1) Enter to the Monitoring page.
2) Tap " " at the upper right.
3) Tap "Share Device", and follow the instructions
to complete.
Method 1: When the device is in Online status,
remove it from the Tuya account and then the
device will enter the RESET status.
Method 2: Open the back cover of the device, long
press the RESET button for about 3 seconds, it will
reset.
NOTE: If using Method 2 to reset the device, only
the Tuya account previously added the device can
add it again. If other Tuya accounts attempt to add,
it will prompt that the device is bound.
1. Device offline
Check if the router is able to connect to the
Internet. If yes, long press the RESET button to
reset the device and add it again.
2. Batteries drain fast
Open the cover and replace the batteries.
4. When connecting the solar panel,
batteries are always low voltage.
Adjust the location of the solar panel, make sure
it will get as much direct sunlight to fall upon it as
possible.
4
3
1
2
3. Add the Device
Tap "+" at the upper right, then tap "Video
Surveillance" and select "Smart Camera".
Check "Make sure the indicator is flashing quickly
or a prompt tone is heard" and then tap "NEXT".
4. Network Configuration
1
2
3
1
5
-
20
c
m
B. By AP mode
4
A. By scanning the QR code
1) Tap "QR Code" at the upper right, then from the
drop-down menu, select "QR Code".
2) Enter the password of your 2.4GHz WiFi, then
tap "NEXT".
3) Point your mobile phone displaying the QR code
to the camera. The distance between your mobile
phone and the camera should be 15– 20cm.
4) When your mobile phone shows the "Security
Camera" page as below, tap "Done" to complete.
Now, the device has been added successfully.
APP Operation
1) From the drop-down menu, select "AP Mode"
and then tap "Next".
2) Enter the password of your 2.4GHz WiFi, then
tap "NEXT". On the next page, tap "Go to
Connect" to complete the hotspot connection.
When motion detection function is enabled and
when it detects a visitor, the doorbell will be awake
from standby mode and enters to recording mode.
2
1
Once you add the device successfully, it will be
bound to your Tuya account and other people are
not able to add it. In this situation, you can share
the device to other people. Only when you remove
the device from your Tuya account, other people
can use their Tuya account to add it.
When monitoring or talking, tap " " to unlock.
3) After connecting the hotspot, return to the APP
to add the device. When your mobile phone shows
the "Security Camera" page as below, tap "Done"
to complete. Now, the device has been added
successfully.
NOTE:
Motion Detection :
Unlock:
Make sure your mobile phone has been connected
to the 2.4GHz WiFi, then open the "TuyaSmart"
APP (Note that 5GHz WiFi is not supported).
1. Connect to the WiFi
2. Register a TuyaSmart account
Follow the instructions on the APP to complete the
account registration. Once done, it will show the
"Welcome Home" page as below.
Add the Device
Batteries built-in device can EXPLODE, CATCH FIRE,
and/or CAUSE BURNS if disassembled, punctured, cut,
crushed, short-circuited, incinerated, recharged, or
exposed to water, fire, or high temperatures. To ensure
optimal safely and performance.
Use only batteries that contain built-in fault and heat
protection. DO NOT use counterfeit or inferior-quality
batteries in Wire-Free cameras. Use only the batteries
supplied by official, or high-quality batteries from,
established, well-known manufacturers, such as
Panasonic®，Energizer®, or Duracell®.DO NOT use
rechargeable batteries. DO NOT place loose batteries in
a pocket, purse, or other receptacle containing metal
objects.
DO NOT store batteries with hazardous or combustible
material; store in cool, dry, ventilated area. While your
CAM2 Wire-Free camera is weatherproof and safe to use
outside. DO NOT allow the batteries or battery
compartment to get wet prior to or during installation.
ALWAYS keep batteries away from children. REPLACE
ALL batteries at the same time with batteries of the same
type purchased at the same time from the same
manufacture and DO NOT load batteries backwards.
MAKE SURE the battery compartment is empty and free
of any loose debris before inserting batteries.
Follow the directions in the quick start guide and/or
written on the Wire-Free camera.
Follow local guidelines to dispose of used batteries. To
the extent permissible by applicable law, failure to follow
these warnings and/or directions could result in damage
to your CAM2 Wire-Free cameras that will not be covered
by our warranty.
In this case, you need to remove the device from
the bound Tuya account first. Before removing,
make sure the device is in online status. After
removing, it will be reset and you should be able
to pair the device.
5. Unable to pair the device due to
bound to one Tuya account.
WARNINGS
6. Unable to unlock
Check if the wiring is correct. Too long or too thin
wires may cause unlocking failure.
Warning: Changes or modifications to this unit not expressly
approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two
conditions: (1) this device may not cause harmful interference,
and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
Shielded cables must be used with this unit to ensure compliance
with the Class B FCC
limits.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide
reasonable protection against harmful interference in a residential
installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver
is connected.
- Consult the dealer or an ex erienced radio/TV technician for hel
p
.
FCC Warnings
RF Exposure
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and operated with
minimum distance 20cm between the radiator your body.