Version:1.0 User Manual Blood Pressure Monitor LS810-B Wrist Type MEM FCC ID: OU9LS810-B01 GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD Zone A, 5/F., Investment Building, No. 12, Huizhan East Rd., Torch Development District, Zhongshan, Guangdong, 528437, China EC REP SET Thank you very much for selecting TRANSTEK Blood Pressure Monitor LS810-B.
Table of Contents Table of Contents INTRODUCTION ............................................................. 2 General Description Measurement Principle Safety Information Indications for Use LCD Display Signal Monitor Components BEFORE YOU START ........................................................6 Power Supply and Charge Power Setting Date and Time MEASUREMENT .............................................................
INTRODUCTION INTRODUCTION General Description Thank you for selecting TRANSTEK blood pressure Monitor (LS810-B). The monitor features blood pressure measurement, pulse rate measurement and auto-save the result. The design provides you with two years of reliable service. Reading taken by the LS810-B are equivalent to those obtained by a trained observer using the cuff and stethoscope auscultation method.
INTRODUCTION INTRODUCTION LCD Display Signal Monitor Components SYSTOLIC DIASTOLIC PULSE RATE TIME MEM/UP BUTTON MEM SET START/OFF BUTTON SET/DOWN BUTTON Systolic Blood Pressure High blood pressure Diastolic Blood Pressure Low blood pressure Pulse beat/minute Low Battery Low battery and please charge the power.
BEFORE YOU START BEFORE YOU START Power Supply and Charge Power 1. The battery of LS810-B is built-in rechargeable lithium-ion battery, the battery current is 420 mAh. 2. Please use the AC adaptor and USB cable to charge the battery, just like the following picture: Setting Date and Time Please proceed to time setting before your initial use so as to ensure each piece of record are labled with a time stamp. (Year Range: 2012-2052; Time Format: 12 Hours) 1.
BEFORE YOU START MEASUREMENT Positioning the Cuff 4.Repeat step 2 and 3 to confirm [MINUTE]. 1.Remove all accessories (watch, bracelet, etc) from your left wrist. If your physician has diagnosed you with poor circulation in your left wrist, use your right wrist. 2.Roll or push up your sleeve to expose the skin. 3.Apply the cuff to your left wrist with your palm facing up. 4. Position the edge of the cuff about 1-2 cm. 5.
MEASUREMENT MEASUREMENT Pair-up the Blood Pressure Monitor Start Measurement with Your Device 1.Turn on Bluetooth and the app. Make sure both are ON when pair-up is proceeding. 2.When the monitor is OFF, press and hold the START button to start pair-up. The symbol and the symbol will be shown on the LCD alternatively, indicating pair-up is proceeding. If SUCCEED, symbol be shown on the LCD. If FAIL, symbol shown on the LCD. 1.
MEASUREMENT DATA MANAGEMENT 2.This device will proceed to data transmission automatically after measurement. The Bluetooth symbol blinks on the LCD indicates data is transmitting. Recall the Records 1.Press “MEM” button to access the memory. The monitor will display the calculated average of the last three readings first. 3.If the data is successfully transmitted, the LCD will then display “dONE”. 2. Press “MEM/UP” button or “SET/DOWN” button to rotate the history records.
INFORMATION FOR USER DATA MANAGEMENT Delete the Records Tips for Measurement When you did not obtain the accurate measurement, you can clear all the measuring results by following below steps. It can cause inaccuracy if the measurement is taken in the following circumstances. 1.Under Memory Recalling Mode, press and hold both the “MEM” button and the “SET” button for 3 seconds.
INFORMATION FOR USER ABOUT BLOOD PRESSURE Maintenance What are systolic pressure and diastolic pressure? To obtain the best performance, please follow below instructions. ME M MEM SET SET Put in a dry place and avoid the sunshine Avoid immersing it in the water. Clean it with a dry cloth in case. When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure.
ABOUT BLOOD PRESSURE TROUBLESHOOTING This section includes a list of error messages and frequently asked questions for problems you may encounter with your blood pressure monitor. If the products not operating as you think it should, check here before arranging for servicing. Why my blood pressure is varies even in one day? 1.
CONTACT INFORMATION SPECIFICATIONS Power supply 3.7V 420mAH Built-in rechargeable lithium-ion battery, 5V / 1A USB AC Adaptor Display moder Digital LCD V.A.46.5x36.5mm Measurement mode Oscillographic testing mode Measurement range Pressure: 0kpa-40kpa（0mmHg-300mmHg） pulse value:(40-199)beat/minute Pressure: 5℃-40℃within±0.4kpa(3mmHg) Accuracy 0℃-45℃(out of 5℃-40℃) within±0.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Table 2 Guidance and manufacturer’s declaration – electromagnetic immunity – for all ME EQUIPMENT and ME SYSTEMS Guidance and manufacture’s declaration – electromagnetic immunity The LS810-B is intended for use in the electromagnetic environment specified below.
NOTE 1 NOTE 2 a b At 80 MHz and 800 MHz, the higher frequency range applies. These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. Field strengths from fixed transmitters, such as base stations for radio (cellular / cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast cannot be predicted theoretically with accuracy.
