version:1.0 User Manual Blood Pressure Monitor TMB-1597-BN Arm Type Guangdong Transtek Medical Electronics Co., Ltd. Zone B, No.105 ,Dongli Road, Torch Development District, Zhongshan,528437,Guangdong,China Thank you very much for selecting TRANSTEK Blood Pressure Monitor TMB-1597-BN. Please do read the user manual carefully and thoroughtly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems.
CATALOGUE CATALOGUE Table of Contents INTRODUCTION..................................................................................................................2 General Description Indications for Use Contraindications Measurement Principle Safety Information LCD Display Signal Monitor Components List BEFORE YOU START..........................................................................................................
INTRODUCTION General Description Thank you for selecting TRANSTEK arm type blood pressure monitor (TMB-1597-BN). The monitor features blood pressure measurement, pulse rate measurement and the result storage. The design provides you with two years of reliable service. Readings taken by the TMB-1597-BN are equivalent to those obtained by a trained observer using the cuff and stethoscope auscultation method.
INTRODUCTION INTRODUCTION CAUTION CAUTION * This device is intended for adult use only. It is not intended for use with neonatal patients, pregnant or pre-eclamptic patients. * The device is not intended for patient transport outside a healthcare facility. * The device is not intended for public use. * This device is intended for no-invasive measuring and monitoring of arterial blood pressure.
INTRODUCTION INTRODUCTION LCD display signal Monitor Components Component list of pressure measuring system 1 Cuff 2 Air pipe 3 PCBA 4 Pump 5 Valve CUFF AIR HOSE MEM BUTTON AIR CONNECTOR PLUG SYMBOL DESCRIPTION SET BUTTON EXPLANATION START/STOP Systolic blood pressure High blood pressure Diastolic blood pressure Low blood pressure Pulse in beats per minute Pulse display Deflation symbol Memory kPa mmHg Low battery Batteries are low and need to be replaced Blood pressure monitor is detecting an
BEFORE YOU START BEFORE YOU START The Choice of Power Supply Setting Date, Time and Measurement Unit 1.Battery powered mode: It is important to set the clock before using your blood pressure monitor, so that a time stamp can be assigned to each record that is stored in the memory. (The setting range of the year :2016—2056; Time format:24H) 6VDC 4×AA alkaline batteries 2.AC adaptor powered mode: 6V 1A (Please only use the recommended AC adaptor model).
BEFORE YOU START 3. When you get the right year, press “ BEFORE YOU START ” button to set down and turn to next step. 5 .Repeat steps 2 and 3 to set the [HOUR] and [MINUTE]. 6.Repeat steps 2 and 3 to set the [UNIT]. 4.Repeat steps 2 and 3 to set the [MONTH] and [DAY]. 7. After the unit is set,the LCD will display “done” first, then display all the settings you have done and then turn off.
BEFORE YOU START BEFORE YOU START Select the User 1. When the monitor is off, press and hold “ user setting mode. The user ID will blink. ”button to enter Pair - up the Blood Pressure Monitor with Your Device Before you start pairing, please download the MedM Health app from APP Store or Google Play in your device which supports Bluetooth 4.0 technology first. 1. Turn on Bluetooth and the app. Make sure both are ON when pair-up is proceeding.
BEFORE YOU START MEASUREMENT Tie the cuff 4.The monitor will shut off after Pair-up process is complete. Bluetooth Module No.: AW51822 RF Frequency Range: 2402 MHz to 2480 MHz Output Power Range: 4 dBm Supply Voltage: 1.8V-3.6 V Transmitting Distance: 10 meters List of compatible devices: For iOS devices: The operating system must be iOS 8 or more, such as iPhone 4S, iPhone 5/5C/5S, iPhone 6/6 Plus and so on. For Android devices: The operating system must be 4.3 or more.
MEASUREMENT MEASUREMENT Start the Measurement 1. When the monitor is off, press “ will finish the whole measurement. (Take user 1 for example.) LCD display ” button to turn on the monitor, and it 2.This device will proceed to data transmission after measurement. The Bluetooth symbol blinks on the LCD indicates data is transmitting. Adjust the zero. Transmitting Inflating and measuring. Display and save the measurement results. The year, date and time will display alternately. Complete 3.
DATA MANAGEMENT DATA MANAGEMENT Recall the Records 1. When the monitor is off, please press “ value of the latest three records. (Take user 1 for example.) 2. Press “ ” button or “ ” button to show the average 3. If you want to check another user’s records, press “ ” button to turn off the monitor when the blood pressure monitor is in the memory inquiry mode.
INFORMATION FOR USER DATA MANAGEMENT Delete the Records If you did not get the correct measurement, you can delete all results for the selected user by following steps. (Take User 1 for example.) 1. Hold pressing “ ” button about 3 seconds when the monitor is in the memory recall mode, the flash display “ dEL ALL”+ User ID will show. Note: To exit out of delete mode without deleting any records, press “ ” button before pressing " " button to confirm any delete commands.
ABOUT BLOOD PRESSURE INFORMATION FOR USER What are systolic pressure and diastolic pressure? Maintenance In order to get the best performance, please follow the instructions below. When ventricles contract and pump blood out of the heart, the blood pressure reaches its maximum value in the cycle, which is called systolic pressure. When the ventricles relax, the blood pressure reaches its minimum value in the cycle, which is called diastolic pressure.
TROUBLESHOOTING ABOUT BLOOD PRESSURE Why does my blood pressure fluctuate throughout the day? 1. Individual blood pressure varies multiple times everyday. It is also affected by the way you tie your cuff and your measurement position, so please take the measurement under the same conditions. 2.If the person takes medicine, the pressure will vary more. 3.Wait at least 3 minutes for another measurement.
SPECIFICATIONS Power supply Display mode Measurement mode Measurement range Accuracy Normal working condition Storage & transportation condition Measurement perimeter of the upper arm Weight External dimensions Attachment Mode of operation AUTHORIZED COMPONENT Battery powered mode: 6VDC 4×AA alkaline batteries AC adaptor powered mode: 6V 1A (Please only use the recommended AC adaptor model). Blue LCD display with white backlight V.A.
COMPLIED STANDARDS LIST FCC STATEMENT Complied Standards List FCC ID: OU9TMB1597BN Labeling ISO 15223-1:2012 Medical devices - Symbols to be used with medical device labels, labelling and information to be supplied - Part 1 General requirements User manual EN 1041:2008 Information supplied by the manufacturer of medical devices This device complies with Part 15 of the FCC Rules.
EMC GUIDANCE EMC GUIDANCE Table 2 Guidance and MANUFACTURER’s declaration – electromagnetic IMMUNITY – for all ME EQUIPMENT and ME SYSTEMS EMC Guidance 1)This product needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided, and this unit can be affected by portable and mobile RF communications equipment. 2)* Do not use a mobile phone or other devices that emit electromagnetic fields, near the unit.
EMC GUIDANCE EMC GUIDANCE Table 4 Guidance and MANUFACTURER’s declaration – electromagnetic IMMUNITY – for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING Guidance and manufacturer’s declaration – electromagnetic immunity The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment.