Lydsto Self Cleaning Sweeping Robot W� Operating Manual Please read this manual carefully before using the product and keep it properly
Catalog Safety precautions Warning Attention Product introduction � � Main machine � Multi-functional cleaning base station � Dust Box Usage of product Application installation and use � � App connection � Description of cleaning base station display � Operating instructions for switching on and off and cleaning Indicator on Clean the base station status Product cleaning � � Main brush disassembly and installation �� Dust box and filter Removal and installation �� Side brush disassembl
Product parameter �� Warranty Statement �� Product Hazardous Substances Declaration Warranty content Product performance fault set of sweeping and mopping robot Warranty card for sweeping robot products Maintenance records of sweeping robot products �� �� �� �� ��
Safety precautions Please read the manual before use Warning: In order to avoid injury and unnecessary property loss to you and others, please read carefully and follow the following "safety precautions" before use. This section describes security precautions in two aspects: Warning and Caution. "Warning" and "Caution" are important contents for safe use and must be observed.
�. Clean the dust on the plug regularly with dry cloth to avoid fire caused by poor insulation; �. Be sure to insert the plug to the end to avoid electric shock, short circuit and fire; �. In case of abnormal fault, please immediately cut off the power supply and stop using it to avoid smoke, fire and electric shock; �. When the product is being charged or used, there is abnormal heating and deformation of the body , burning smell and abnormal sound in operation.
Product introduction Main machine Cover buckle position Dust box take out button Lidar pressure sensor Wall sensor Panel Reset key Dust box Air outlet Charging contact (�) Infrared receiving sensor function button Bumper Infrared window sensor Infrared receiving sensor Suction inlet Function button Partial cleaning button Press to clean the specific area, and automatically recharge after cleaning Short Press pause while running Long press the switch Short press overall cleaning to automatically r
Multi-functional cleaning base station Function button Start/pause Recall Mop cleaning Automatic dust collection Infrared lens Power port Suction port Head cover Cleaning brush Dust bag Clean water tank Sewage water tank LED display Guide whee (�) Charging clip (�) Sewage extraction port Usage of product Step �: Remove the limiter strips on both sides of the bumper; Infrared lens (�) Cleaning tray Step �: paste the mop in the mop support paste area, the mop support assembly limit into the bott
Step �: Find a suitable place to place the cleaning base station, and ensure that the cleaning base station is placed horizontally; Step �: Take out the clean water tank, remove the cover of the clean water tank, put the clean water tank after water injection (the water amount is lower than MAX line) back to the cleaning base station, and cover the top cover of the cleaning base station; Water injection Longer than �.� m Longer than �.� m Max line Longer than �.
Application installation and use Connect to Lydsto APP Connect to MIJIA APP The product has been connected to MIJIA. It can be controlled by MIJIA APP and interconnected with other products. Scan the QR code, download and install MIJIA APP. Users with MIJIA APP already installed will directly enter device connection page. Or search "MIJIA" in APP store, download and install MIJIA APP.
Operating instructions for switching on and off and cleaning Area one Area two Area four Area three �.Power on/off Power on: Long press the switch button, switch button indicator light up, the robot into standby state; Shutdown: Long press the switch button, the indicator light slowly extinguished and shutdown; �.
Description of Multi-functional cleaning base station display Power on the cleaning base , the display screen is steady on, if there is no operations with the base or �� seconds, and the screen goes off.
Product disassembly and cleaning Please carry out the following cleaning steps in the case of power off! Disassembly and installation of main brush assembly Step �: Main brush disassembly Turn over the machine, hold the release button of the roller brush box and move to the center respectively, remove the outer cover of the main body;Remove the main brush, clean the surface attachment.
Attention �. Please replace the side brush configured by the original factory to ensure the cleaning effect; �. Replace the edge brush with a screwdriver to avoid scratches; �. Due to a sharp blade in clean knife, please keep it our of the touch of children.
Mop disassembly and installation Step �: mop removal Remove the mop module from the chassis and remove the mop cloth from the mop bracket; Step �: mop cleaning Rinse the mop with clean water and dry it to prevent dust clumping and unpleasant smell when it is used again. Attention �. Please replace the mopping cloth configured by the original factory, so that the cleaning effect of the main engine will not be affected because of different products; �.
Multi-functional cleaning base station cleaning Step �: Dust bag replacement When the dust bag is full, replace the dust bag as prompted by the base station display screen.
Multi-functional cleaning base station parts Step �: Clean the sewage tank Open the top cover of the cleaning base station, take out the sewage tank, open the sewage tank to release the buckle, clean the dirt in the water tank with a long cleaning brush, and put it back to the cleaning base station after cleaning. Step �: Clean the tray base Take out the tray base and use a cleaning brush to clean up the dirt, and then install it back to the base station.
Error �: Check whether the main brush is stuck Error �: Check if the side brush is stuck Error �: Check whether the main wheel is stuck Error �: Please return the dust box Error �: Low battery, please charge Error �: The charging fails. Check whether the connection between the robot and the base station is normal Please check whether the main brush is entangled with wool, wires and other sundries.
Error �: Please load the cleaning tray Error ��: Dust bag not in place, please check Error ��: Base station wind pressure is abnormal Error ��:Dust bag is full Error ��: Dust collection is abnormal Check whether the cleaning tray is in place or properly installed, and reinstall the cleaning tray Check whether dust bags are installed If dust bags have been installed, check whether the dust bags are inserted to the bottom Please check that the base station roof is properly closed Please check whether the
Types of problem Solution During the cleaning, the power is insufficient and the cleaning is not continued Ensure that the robot is not in do not disturb mode, which does not continue scanning.
Manufacturer: Guangdong Yimu Technology Co., Ltd. Service number: +86-400-077-8387 Address: Room 201,Building 1,No.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.