User's Manual

R/C Introduction Manual
18
2.17 TH HOLD
4.Firstly main channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L
and R separately correspond to the rate of Left and Right servos of the main channel mix
5.Secondly sub channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L
and R separately correspond to the rate of Left and Right servos selected in the sub
channel.
6.Third Press ENTER to select EN item. Use +/- to select “ON” to enable the function,
and “OFF” to disable the function.
7.Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return
to the Main Screen.
For example: current setting: ST: L 50% R 30%
TH: L 20% R 50%
EN: select “ON”
If throttle servo is 60% on the right and rudder servo is 50% on the right, and then
after setting, throttle servo is: 50*30%+60%*50%=45%. Throttle servo will act along with
the action of STEERING servo.
T H H O L D 1 0 . 2 V T H H O L D 1 0 . 2 V
V A L U E : 0 %
T H . H O L D :
--This function allows the Throttle Servo to be set to
a percentage of the total travel range. This is an
alternative to using the motors choke when starting up
the model.Throttle hold can be performed by pressing
the switch to stop the engine. It can be performed for
accident braking. When pressing the switch, throttle
trigger doesn't work until the switch is pressed again.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the TH HOLD function
and press ENTER.
3.Use the +/- Key to change the value.
4.Press EXIT twice to save and return to FUNCTION
MENU, press EXIT again to return to the Main Screen.
TERMS:
VALUE -- Throttle hold position. Range: -120% to
+120%.. Default value: 0%.
SERVO
0
50%
100%
120%
50%
100%
120%
RIGHT
FWD
LEFT
BACK
TH.HOLD
2.16 MIX
M I X 1 0 . 2 V M I X 1 0 . 2 V
: L 5 0 R 5 0
S T : L 5 0 R 5 0
E N : ON OF F
S T
R/C Introduction Manual
17
B K - M I X 1 0 . 2 V
2.15 BK-MIX
: 1 0 0 %
E N : O N O F F
R A T E
BR_MIX --BRAKE MIXING
When using a secondary brake system set the BRAKE MIX value to a percentage of the
Throttle Brake.
This mixing uses the 2nd channel to control the rear brakes and the 3rd channel to
control the front brakes. This function can be used in conjunction with the TH TRIM and TH
EPA to fine tune the power and balance of the overall braking system.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the BR_MIX function and press ENTER.
3.Press ENTER to select a item.
4.Use the +/- Key to change the value.
5.Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return
to the Main Screen.
TERMS:
RATE -- the rate of brake between 3rd channel and 2nd channel. Default value: 0
120%.
EN -- the start or close switch of this function. Select “ON” to start the function,
and “OFF” to close the function
This function allow customer to apply mixing between the steering, throttle, and
channel 3channels.There are main channel and sub-channel in the MIX selection. The
servo travel value of the sub channel is changed along with the change of the main channel
according to the setting rate.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the BR_MIX function and press ENTER.
3.Press ENTER to select a item.
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
9 : S P E E D
1 0 : A T S
1 1 : M O D U L A T E
1 2 : B R _ M I X
B K - M I X 1 0 . 2 V
: 8 0 %
E N : O N O F F
R A T E
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
1 3 : M I X
1 4 : T H H O L D
1 5 : F / S
1 6 : N E U T R A L
M I X 1 0 . 2 V M I X 1 0 . 2 V
S T : L 5 0 R 5 0
: L 6 0 R 5 0
E N : ON OF F
T H
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
1 3 : M I X
1 5 : F / S
1 6 : N E U T R A L
1 4 : T H H O L D