User's Manual

R/C Introduction Manual
20
2.20 SOUND
This function can open or close the buzzer sounding.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the SOUND function and press ENTER.
3.Use the +/- Keys to select INH or ACT.
4.Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return to
the Main Screen
S O U N D 1 0 . 2 V S O U N D 1 0 . 2 V
S O U N D : I N H S O U N D : I N H
S Y S T E M
R e s e t S y s t e m ?
2.21 RESET
--All the setting in the system will be reset to the
default values by this reset function. It takes about 30
seconds.
1.Press “ENTER” to see FUNCTION MENU.
2.Use the +/- Keys to select the RESET function and
press ENTER.
3.Press ENTER to reset the N-4Q memory.
4.Press“ EXIT”twic e to save and retur n to
FUNCTION MENU, press EXIT again to return to the Main
Screen.
2.22 MODEL RESET
M _ R E S 1 0 . 2 V
R e s e t D A T A ?
N O Y E S
R E A D Y
This function will reset the data of the current model memory to default values.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the M_RES function and press ENTER.
3.Use the +/- Keys to select YES
4.Press ENTER to reset the data
5.Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return
to the Main Screen
R/C Introduction Manual
2.18 F/S
19
This function does not work in PPM mode. If the RF signal loss ,it should occur the
receiver adjust the Steering or Throttle or both to a preset value. The servo value of
Steering channel and Throttle channel in the fail status can be set through fail safe
function.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the F/S function and press ENTER.
3.Press ENTER to select a item.
4.Use the +/- Key to change the value.
5.Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return
to the Main Screen.
TERMS:
ST -- To set the servo value of Steering channel. Range -120% to +120%. Default: 0%.
INH disable this channel Fail Save function. ACT---enable.
F / S 1 0 . 2 V
S T : 0 %
T H : 0 % I N H
E N : O N O F F
A C T
2.19 NEUTRAL
This function can calibrate the neutral of the STEERING wheel or THROTTLE trigger.
1.Press “ENTER” to see FUNCTION MENU
2.Use the +/- Keys to select the NEUTRAL function and press ENTER.
3.Use the +/- Keys to select YES.
4.Press ENTER to calibrate the neutral.
5.Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return to
the Main Screen
Note: Don't movement the STEERING wheel or THROTTLE trigger in the calibrate
procedure.
N e u t r a l 1 0 . 2 V
N O Y E S
R E A D Y
S e t N e u t r a l ?
F u n c t i o n 1 0 . 2 V
1 3 : M I X
1 4 : T H H O L D
1 6 : N E U T R A L
1 5 : F / S
F / S 1 0 . 2 V
S T : 0% A C T
T H : 2 0 %
E N : ON O F F
I N H
F u n c t i o n 1 0 . 2 V
1 3 : M I X
1 4 : T H H O L D
1 5 : F / S
1 6 : N E U T R A L
N e u t r a l 1 0 . 2 V
N O
O K
Y E S
S e t N e u t r a l ?
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
1 7 : S O U N D
1 8 : R E S E T
1 9 : M _ R E S
2 0 : T I M E R
S O U N D 1 0 . 2 V S O U N D 1 0 . 2 V
S O U N D : A C T S O U N D : A C T
F u n c t i o n 1 0 . 2 V
1 7 : S O U N D
1 8 : R E S E T
2 0 : T I M E R
1 9 : M _ R E S
M _ R E S 1 0 . 2 V
R e s e t D A T A ?
N O
O K
Y E S