User's Manual

R/C Introduction Manual
8
R/C Introduction Manual
7
E P A 1 0 . 2 V E P A 1 0 . 2 V
S T T H A U X
1 2 0 % 1 0 0 %1 0 0 %
2.4 EPA
F
B
! Use this when performing left and right steering
angle adjustments, throttle high side/brake side
operation amount adjustment, and channel 3 servo
up side/down side operation amount adjustment
during linkage.
! EPA adjusting value range: 0~120 %, default is
100%
1.Press “ENTER” in the power on interface and
enter function menu. Press “+” or “-” to
choose “EPA”. And press “ENTER” and enter
EPA adjusting interface.
2.Press “ENTER” to choose each adjusting item,
and then press “+” to increase and “-” to
decrease the value of the corresponding item.
3.Press “EXIT” to save your setting and leave EPA
interface, and back to the function menu interface.
TERMS:
F-FORWARD,B-BACK,ST-STEERIN,
TH-THROTTLE,AUX-AUXILLIARY
SERVO
0
50%
100%
120%
50%
100%
120%
RIGHT
FWD
LEFT
BACK
2.3 Main-Menu Function
1 0 . 2 v
D / R :
7 0
H L D :
O F F
M O D :
H R F
S T .
T H .
Voltage
Model Name
Timer
Steering Trim
Throttle Trim
Modulation
Throttle Hold
Steering
Dual Rate
M 0 0 : m o d 0 0
T _ I : 0 0 : 0 0
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
1 : E P A
2 : D / R
3 : S _ T R I M
4 : R E V
1 0 0 % 1 2 0 % 1 0 0 %
E P A 1 0 . 2 V E P A 1 0 . 2 V
S T T H A U X
1 2 0 % 1 0 0 %8 0 %
F
B
1 0 0 % 1 2 0 % 1 0 0 %
2.6 S_TRIM
S _ T R I M 1 0 . 2 V S _ T R I M 1 0 . 2 V
S T :
T H : 0
0
--Use this function to adjust the neutral position of
the steering and throttle servos.
--SUB TRIM adjusting value range: -100-100
Default is 0
1.Press “ENTER” to see FUNCTION MENU.
2.Press “+” or “-“ to choose TRIM, and press
“ENTER” to enter SUB TRIM adjusting interface.
3.Press “+” to increase and “-” to decrease
SUB TRIM value.
4.Press “EXIT”to save your setting and leave SUB TRIM interface, and back to the
function menu interface.
TERMS: ST-STEERING, TH-THROTTLE
2.5 D/R
--D/R is used to change the action range of steering
servo when turning the steering wheel. Increasing D/R
will make the steering wheel action more sensitive.
--D/R adjusting value range: 0~120%, POS0
default value is 100%,POS1 default value is 70%.
--Press the ST.D/R dial to select POS0 or POS1, and
the value will display in the LCD when it is on the main
screen.
1.Press “ENTER” to see FUNCTION MENU.
2.Press “+” or “-“ to choose D/R, and press
“ENTER” to enter D/R adjusting interface.
3.Press “+” to increase and “-” to decrease D/R
value.
4.Press “EXIT”to save your setting and leave D/R
interface, and back to the function menu interface.
TERMS: POS-POSITION
S T D / R 1 0 . 2 V S T D / R 1 0 . 2 V
P O S 0 :
P O S 1 : 1 0 0 %
7 0 %
SERVO
0
50%
100%
120%
50%
100%
120%
RIGHT
FWD
LEFT
BACK
ST. D/R
F u n c t i o n 1 0 . 2 V F u n c t i o n 1 0 . 2 V
1 : E P A
3 : S _ T R I M
4 : R E V
2 : D / R